0.2 m 0.7 m 0.6 m 0.9 m 0.4 m 0.3 m C 0.9 m B 0.6 m 0.35 m 0.4 m 0.6 m Fig. P3.59 and P3.60 3.60 The triangular plate ABC is supported by ball-and-socket joints at B and D and is held in the position shown by cables AE and CF. If the force exerted by cable CF at C is 33 N, determine the moment of that force about the line joining points D and B.

0.2 m 0.7 m 0.6 m 0.9 m 0.4 m 0.3 m C 0.9 m B 0.6 m 0.35 m 0.4 m 0.6 m Fig. P3.59 and P3.60 3.60 The triangular plate ABC is supported by ball-and-socket joints at B and D and is held in the position shown by cables AE and CF. If the force exerted by cable CF at C is 33 N, determine the moment of that force about the line joining points D and B.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.10P: Draw the FBD of the entire frame, assuming that friction and the weights of the members are...

See similar textbooks

Similar questions

Draw the FBD of the entire frame, assuming that friction and the weights of the members are negligible. How many unknowns appear on this FBD?
A horizontal board weighing Wb = 600 N is hinged to a vertical wall. A personweighing Wp = 400 N stands at the end of the board 5 m from the wall. A rope is attached to theboard at a point 3 m from the wall and makes an angle of θ = 40° with theboard. Determine the tension (T) in the rope
Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
The simplest truss consists of two rods and is loaded by the force F. Given: F = 5,1 kN. Angle α = 69 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 2,2 kN. Angle α = 39 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N2 in the rod 2, considering that N2>0 for tension and N2<0 for compression.
The truss is supported by short links at A, B, and C. Suppose that F={450j}lb
A turbine is connected to a generator by means of flange coupling that has a bolt circle diameter of 20 in. The generator output is 40 Hp, 3600 rpm and 90% efficiency. If there are 10 bolts, determine the force acting on each bolt in kN.
A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 13.0 m long, and pivots about a hinge at its lower end. A cable is connected 3.80 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. a) What is the tension in the cable? b) Find the magnitude of the force the hinge exerts on the bridge. Find the direction of the force the hinge exerts on the bridge. c) If the cable suddenly breaks, what is the initial angular acceleration of the bridge?
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar
One end of a post weighing 400 Nand with height h rests on a roughhorizontal surface with ms = 0.30.The upper end is held by a ropefastened to the surface and makingan angle of 36.9° with the post. A horizontal force F isexerted on the post as shown. (a) Ifthe force F S is applied at the midpointof the post, what is the largest value it can have without causing the postto slip? (b) How large can the force be without causing the post to slip ifits point of application is 6/10 of the way from the ground to the top of thepost? (c) Show that if the point of application of the force is too high,the post cannot be made to slip, no matter how great the force. Find thecritical height for the point of application.
Ancient pyramid builders are balancinga uniform rectangular stoneslab of weight w, tipped at anangle u above the horizontal, usinga rope (Fig.). The rope isheld by five workers who share theforce equally. (a) If u = 20.0°, whatforce does each worker exert on therope? (b) As u increases, does eachworker have to exert more or lessforce than in part (a), assuming theydo not change the angle of the rope? Why? (c) At what angle do theworkers need to exert no force to balance the slab? What happens if uexceeds this value?
The structure shown in Fig. (a) is supported by ball-and-socket joints at O and D, and by a slider bearing at C. The two members OABC and AD, connected by a ball-and-socket joint at A, each weigh 20 N/m. (1) Draw the FBD for the entire structure, and count the unknowns. (2) Draw the FBD for each of the members, and count the total number of unknowns.