00 AT&T LTE 10:15 AM e* 49% a bbl-app.learn.fresnostate.edu 1 of 2 A concrete wall footing with a width of 0.9m and a depth of 0.6m supports a centrally placed 0.6-m-thick wall. The ultimate bearing stress for the soil under the footing is 475 kN/m?. What is the height of the wall if a factor of safety of 5.0 is used? Concrete weighs 23.5 kN/m3.

00 AT&T LTE 10:15 AM e* 49% a bbl-app.learn.fresnostate.edu 1 of 2 A concrete wall footing with a width of 0.9m and a depth of 0.6m supports a centrally placed 0.6-m-thick wall. The ultimate bearing stress for the soil under the footing is 475 kN/m?. What is the height of the wall if a factor of safety of 5.0 is used? Concrete weighs 23.5 kN/m3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What sho..ld be tre minimum wall crickness of a ocol witn 1.20 m ard Axbm wal s or the grounc when water is f lled anc C30 concrete is used for the wal s to show Strength? Projoct tre pool
Design a RC square footing by Ultimate Strength ACI Column dimensions: 14''x14'' LL= 100 k DL = 71 k qall= 4 ksf f'c = 3 ksi fy = 60 ksi
The layout of a 200 mm thick unrestrained slab over a proposed single garage has internaldimensions of 6000 x 3000 mm and supports a live load of 1.5 kN/m2. It is supported by 230mm thick walls. The environmental conditions are mild, and 1 hr fire rating is required.Determine the suitable reinforcement and check the code requirements for shear, minimumarea of reinforcement and bar spacing.Assume deflection is ok (no need to check), fcu= 30 MPa, fy = 450 MPa and Ø 12 mmreinforcement bars for effective dep
The layout of a 200 mm thick unrestrained slab over a proposed single garage has internal dimensions of 6000 x 3000 mm and supports a live load of 1.5 kN/m². It is supported by 230 mm thick walls. The environmental conditions are mild, and 1 hr fire rating is required. Determine the suitable reinforcement and check the code requirements for shear, minimum area of reinforcement and bar spacing. Assume deflection is ok (no need to check), feu= 30 MPa, fy= 450 MPa and Ø 12 mm reinforcement bars for effective depth.
A square column with side dimension of 70 mm rests on top of a timber footing. It is determined that the column carries an axial load of 752 kN. If the punching strength of concrete is 14.69 MPa, determine the minimum thickness (mm) of the footing. Hiiiiiii need helppp thank u so much urgenttt
Design a square reinforced concrete footing to support a 20-inch square tied concrete column at the edge of the building as shown below. Also check development length and force transfer in the column and at the footing. Draw the reinforcement pattern. Use a footing thickness of 24". Assume the following design conditions: -service dead load= 270 kips -service live load= 135 kips -allowable soil pressure (q)= 5000 psf -f. for the column= 5000 psi -f. for the footing= 3000 psi -fy= 60000 psi -longitudinal column steel consists of #8 bars reinf cement is uncoated -unit weight of the soil is 125 lb/ft3 -normal weight concrete Finished ground line 20" square column Y = 125 lb/ft³ 5'
Foundation: Direct Shear Test
A footing supports a 200mm thick concrete wall. Wall loads: = 175 Dead Load kN/m = 89 Live Load kN/m = 20.6 Concrete, f'c MPа = 415 Steel, fy MPа %3D Unit weight = 23.6 of concrete kN/m3 Factored :1.2D %D load + 1.6L combination Thickness %3D of footing 350mm Steel Cover ( bottom of footing to centroid of 90mm bars) The gross allowable soil pressure is 100 kPa and width of the wall is 200mm. Assume that the top of the footing is at the ground level. A) What should be the width (m) of the footing so that the allowable soil pressure will not be exceeded? (Dimensions in multiples of 50mm) B) Check the adequacy of the footing for Beam Shear considering 1m strip C) Calculate the required spacing reinforcements for diameter 16mm main bars and 10mm shrinkage and temperature bars.
4. A 2.10m x 2.10m footing carries concentrically a square column 0.40m x 0.40m. Design data: Column factored loads: DL = 570KN = 460KN %3D Concrete cover to the centroid of footing reinforcement = 110mm Concrete f'c - 21MPA Steel fy= 415MPA %3D %3D Allowable stresses at ultimate loads: For diagonal tension or two-way action shear = 1.52MPA For wide-beam shear 0.78MPA Maximum steel ratio for moment = 0.016 a. What is the minimum thickness (mm) of footing required for punching shear? b. Determine the minimum thickness (mm) of footing required for wide beam shear. Determine the minimum thickness (mm) of footing required for maximum moment. C.
(Please Answer PROBLEM 102) PROBLEM 101:A continuous strip footing is to be located concentrically under a 300 mm wall that delivers service loadsD = 360 kN/m and L= 220 kN/m to the top of the footing. The bottom of the footing will be 1.2 m below the finalground surface. The soil has a density of 20Kn/m3and allowable bearing capacity of 280 Kn/m2. Materialsstrengths are fc’ =21 MPa and fy = 276 MPa. Find:a. The required width of footing,b. The required effective and total depths, based on shear,c. The required flexural steel area.d. Give an on-scale schematic structural detail.***Use 20 mm ØPROBLEM 102:Referring to problem 101, design the footing considering the moments induce by the following loads given belowin addition to the service loads:MD = 50 Kn-m Use the following load combinations:ML = 60 Kn-m U= 1.2D + 1.6 LME = 36 Kn-M U = 1.2DL + 1.0L + 1.0Ea. The required width of footing,b. The required effective and total depths, based on shear,c. The required flexural steel area.d.…
Square column size 16" 280 kips, PLL = 180 kips L = 1.5B, fy = 60 ksi, f'c = 4000 psi fa 4 ksf, Footing base = 4'-6" Df PDL find 26", soil weight = 100 pcf, Reinforcement - #8 bars 1) Design for load transfer 2) Development length for the dowels 3) Design bars for footing at both directions 4) Bars fit the footing based on development length 5) Two way footing spacing diagram. 4'-6" 26 B VỈ L Ildi [ld₂ Dowel Configuration B 1.5
Given: Footing Column Required: Steel Works by Direct Count Method 0.35x0.35x4.00 Column with 6-D20mm Column RSB D10mm Lateral Ties @ 0.15m O.C. -1.50x1.50x0.50m Footing with D20mm @ 0.10m O.C. BW