01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter [Est =30,000 ksi, Eat=10,000 ksi]. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assembly. (3) the normal strain in the steel tube (1).

01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter [Est =30,000 ksi, Eat=10,000 ksi]. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assembly. (3) the normal strain in the steel tube (1).

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter4: Mechanical Processes

Section: Chapter Questions

Problem 4.21P

See similar textbooks

Similar questions

1. A pressure gauge at elevation A at the side of a tank containing a liquid reads 80 KPa. Another gaugeat elevation B reads 130 KPa, Compute the ff;a. Specific Weightb. Densityc. Specific Gravity let elevation A= 15m, and elevation B= 5m.
Part 2Two pipes are connected by a manometer as shown. Determine the pressure difference, between the pipes in kPa.
A square plastic bar (length Lp, side dimensions p = 193 mm) is inserted inside a hollow,square, cast iron tube (length Lc = 400 mm, sidesc = 200 mm, and thickness tc = 3 mm). (a) What is the required initial length Lp of theplastic bar so that, when it is compressed bysome force P, the final length of bar and tube areequal to length Lc and, at the same time, the gapbetween plastic bar and cast iron tube is closed?(b) Compare initial and final volumes for theplastic bar.Assume that Ec =170 GPa, Ep = 2.1 GPa, vc = 0.3,and vp = 0.4.
If the specific weight of glycerin is 79.2 ft/lb³, what suction pressured is required to raise the glycerin 9 in vertically in a ½ diameter tube? The answer was already given, please show the solution. Answer: -0.412 psi
A cylindrical steel tank is manufactured based on the following data:internal pressure: 2460 psifactor of safety with respect to YP: 2.0yield stress in tension (circumferential): 56 000 psiyield stress in shear (longitudinal): 22 000 psi(a) Determine the minimum wall thickness if the diameter of the cylindrical steel tank is 7 inches.(b) Determine the maximum acceptable internal pressure if the wall thickness is 0.50 inches.Use 2 decimal places in every solved values. (25 pts)
For the same condition as the previous problem (After a solid block is put on a scale in the water tank as shown in the picture, the total water volume level increases from 5.0 m3 to 6.0 m3. The reading from the upper spring scale is 36.9 kN, and the reading from the scale in the water is 30 kN. The specific weight of water is γw=9.81kN/m3. ), select the correct value for the specific weight of the object γobject :________ A. 46.71 B. 16.71 kN C. 76.71 kN/m3 D. 65.91 kN/m3
A square plastic bar (length Lp, side dimension sp = 193 mm) is inserted inside a hollow, square, cast iron tube (length Lc = 400 mm, side sc = 200 mm, and thickness tc = 3mm). (a) What is the required initial length Lp of the plastic bar so that, when it is compressed by some force P, the final length of bar and tube are equal to legnth Lc, and, at the same time, the gap between plastic bar and cast iron tube is closed? (b) Compare initial and final volumes for the plastic bar. Assume that Ec = 170 GPa, Ep = 2.1 GPa, vc = 0.3, and vp = 0.4.
Qs.The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft. Calculate the maximum diameter of the cylindrical tank if the internal pressure is 110 psi. Also discuss the joint strength and diameter of tank requirement for the given conditions .If you dont know the answer please skip and let others do , dont post wrong answer, dont waste qsn
Note: Please state what formula you are using. And please be clear and detailed with your solution. Atleast explain. It will help me, thanks. Problem: An open tank in the shape of a frustum of a cone is bound by two hoops, one at the top and the other at the bottom. The diameters at the top and bottom are 2m and 3m, respectively. If the total bursting force is to be taken care of by the hoops, find tension in each hoop if water stands 2 m in the tank. Height of tank is 3.0 m.
A fluid is placed between two parallel plates with area of 2 m2. The lower plate is pulled with 0.4 N with velocity of 0.4 m/s (in x direction), while the upper plate is pulled in other direction (in –x direction) with 0.75 N with velocity of V2 m/s. If the distance between the plates is 1 cm, the viscosity of fluid is 0.01 kg/m.s, find V2.1. Calculate ryx (from the eqn. ryx = ∑ F), consider directions when summing up the forces!2. Use Newton’s law of viscosity to calculate V2
A commercial steel pipe—with a diameter, D, of 200 mm and length, L, of 30 m—is used to drain oil (S.G.=0.8)tank. Determine the discharge, in liters per second, when the oil level in the tank is 3 m above the exit of the pipe.Neglect component or minor losses and quantify the friction losses using the Darcy-Weisbach equation shownbelow, use friction factor, f, of 0.12.
A copper tube 80 mm diameter and 2.5 mm thick is plugged at its ends and filled with water without applying any external pressure . It is observed that when an axial push is applied at ends , the water pressure rises to 0.12 N / mm² . Find value of axial push . Take Ecu = 102 GPa , Kwater = 2.2 GPa and μ = 0.32 .