010 Porter governor has all four arms 200 min long. The upper arms are pivoted on the mus of rolation and the lower arms are attached to a sleeve at a distance of 25 mm from the axs Each ball has a mass of 2 kg and the mass of the load on the sleeve is 20 kg. If the radius of rolation of the balls at a speed of 228 rpm is 100 mm, find the speed of the governor after the sleeve has lifted 50 mm. Also determine the effort, power of the governor and governor sensitivity

010 Porter governor has all four arms 200 min long. The upper arms are pivoted on the mus of rolation and the lower arms are attached to a sleeve at a distance of 25 mm from the axs Each ball has a mass of 2 kg and the mass of the load on the sleeve is 20 kg. If the radius of rolation of the balls at a speed of 228 rpm is 100 mm, find the speed of the governor after the sleeve has lifted 50 mm. Also determine the effort, power of the governor and governor sensitivity

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.16P: The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient...

See similar textbooks

Similar questions

Find the smallest distance d for which the hook will remain at rest when acted on by the force P. Neglect the weight of the hook, and assume that the vertical wall is frictionless.
The 120-kg block A is suspended from a rope that runs around the fixed pegs B and C. The coefficient of static friction between the pegs and the rope is 0.25. Determine the range of the force P for which the system is in equilibrium.
The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient of static friction is 0.2 between the cylinder and the inclined surface, determine whether the cylinder can be at rest in the position shown. Note that the string AB is parallel to the incline.
Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.
Q12 / A Porter governor has links 150 mm long and are attached to pivots at a radial distance of 30 mm from the vertical axis of the governor. The mass of each ball is 1.75 kg and the mass of the sleeve is 25 kg. The governor sleeve ready to rise at 300 rpm when the links are at 30 ° to the vertical. Assuming the friction force to be constant, find the value of the friction force, minimum and maximum speed of rotation when the inclination of the links is 45 ° to the vertical.
The arms of a Porter governor are 300 mm long. The upper arms are pivoted on the axis of rotationand the lower arms are attached to the sleeve at a distance of 35 mm from the axis of rotation. The loadon the sleeve is 54 kg and the mass of each ball is 7 kg. Determine the equilibrium speed when the radius of the balls is 225 mm. What will be the range of speed for this position, if the frictional resistances to the motion of the sleeve are equivalent to a force of 30 N?[Ans. 174.3 r.p.m. ; 8.5 r.p.m.]
The arms of a Hartnell governor are of equal length. At the mid-position of the sleeve, theball arm is vertical and the radius at which the ball rotates is 10 cm when the equilibriumspeed is 400 RPM. On changing the speed by 1% the governor can overcome the frictionat this position. The friction force is assumed to have a constant value of 20 N at thesleeve. The sleeve moves ± 1.5 cm from the mean position. The minimum speed of thegovernor including friction is 450 rpm. The mass of the sleeve is 3.5 kg. Calculate themagnitude of rotating masses and initial compression of
In a governor of the Hartnell type the arms of the bell-crank leversare equal in length, and those carrying the operating masses arevertical when the governor is rotating at its mean speed of 775rev/min, with the masses moving in a circle of 175 mm diameter -The usual central controlling spring is replaced by two paralleltension springs direetly connecting the operating masses. Find(a) the magnitude of each operating mass if a force of 90 N isrequired at the sleeve to maintain it in the mean speed positionwhen the specd is increased from 775 to 800 rev/m in(b) the stiffness, or rate, of each spring if the ratio of sleevemovement to increase of speed is 1 mm to 10 revImin when inthe mean speed position.
In a porter governor the mass of the central load is 18 kgand the mass of each ball is 2kg. the top arms (254) mm while the bottom arms are (304) mm long. The friction of the sleeve is 20 N. If the top arms make 45 deg with the axis of rotation in the equilibrium position, find the range of the speed of the governor in that position
In a porter governor the mass of the central load is 18 kgand the mass of each ball is 2kg. the top arms (250+X) mm while the bottom arms are (300+X) mm long. The friction of the sleeve is 20 N. If the top arms make 45 deg with the axis of rotation in the equilibrium position, find the range of the speed of the governor in that position Note X is the student roll no. for example if the student roll no is A20 then X=20
The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameter of 300 mm and a speed of 1420 rev/min. The coefficient of friction between the belt and the pulley is 0·4 and the angle of lap is 160°. (a) Calculate the tension in each side of the belt at operating speed. (b) Determine the power transmitted when the belt is on the point of slipping. If the pulley system uses a flat belt of CSA 500 mm² and density 1300 kg/m3, determine: (c) The power transmitted, when the mass of the belt is taken into consideration.
A package of mass m is placed inside a drum that rotates in the verticalplane at the constant angular speed ˙ θ = 1.36 rad/s. If the package reaches the position θ = 45◦ before slipping, determine the static coefficient of friction between the package and the drum.