013: Choose the correct answer:1. In a symmetrical three phase system the total instantaneous three phase power is:a. Pulsating sinusoidally with frequency o.b. Pulsating sinusoidally with frequency 30.c. Constant.2. It is impossible to obtain analytical solutions for the power flow equations,because:a. The number of equations is large.b. The equations are nonlinear.c. The number of unknown variables in the equations is large.3. Stability requirements limit the power-handling capability of:a. Long lines.b. Short lines.c. Medium4. Bundling of conductors in a transmission line reduces the risk for corona. Also,it:a. Reduces the sag of the line.b. Increases the resistance of the line.c. Increases the transmission capacity.5. A 50 Hz, turbo generator supplying 40% of its maximum power capability to 0.8pu load. The operating power (torque) angle 8° is:a. 6°=36 elec. deg.b. 8°= 23.57 elec. deg.c. 8°-40 elec. deg.

013: Choose the correct answer: 1. In a symmetrical three phase system the total instantaneous three phase power is: a. Pulsating sinusoidally with frequency o. b. Pulsating sinusoidally with frequency 30. c. Constant.

013: Choose the correct answer: 1. In a symmetrical three phase system the total instantaneous three phase power is: a. Pulsating sinusoidally with frequency o. b. Pulsating sinusoidally with frequency 30. c. Constant.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Related questions

Q: Si R 1.5 kn VR E 30 V FIG. 2.154 Problem 4.

Q: totype AI robot for industry that will be supplied by a 12V dc. This AI robot as they envision has a...

A: Solution- The model can be designed as- From the question, load resistance will be varies as 250 oh...

Q: A base biased transistor circuit with the following element values is given VBB = 10V, VCC = 10V, R...

A: Given RB1= 446.5 kohm RB2= 493.5 kohm Rc= 829 ohm Find IBmax and Ibmin

Q: + ix 10Ω 8 A VB VA Vc 1 )1A )1 A Figure 1 For the circuit shown, write out the equations needed to s...

Q: 3. Design an astable M/V assuming R1 = 150k, R2 = 100k to produce 1 kHz output. %3D %3D Calculate th...

A: Astable multivibrator contain an op Amp and positive feedback circuit which generates an oscillating...

Q: Explain the successive approximation type ADC with neat schematic diagram

A: We need to explain about succesive approximation type of ADC with a block diagram

Q: 3. Consider a three-wire Y-Y circuit. The voltages of the source are Van V3 o Vrms, Vin V3 <- 208 12...

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you ar...

Q: From Figure 3, write node-voltage equations: one for each input terminal of the op amp. o. The expre...

Q: 6) It is required to generate a single pulse waveform (Vtrigg) of 4 Volts amplitude (peak-to peak) a...

Q: Question 1 a) With the aids of a diagram, briefly explain how an N-channel JFET being constructed an...

A: Solution (a) - N-channel JFET - A N-Channel JFET is a type of JFET in which the charge carrier is...

Q: Find Rab in the circuit shown.

Q: PMOS PMOS NMOS NMOS NMOS 9V b. 30

A: The given circuit shows that the sensor which is used is LDR (Light Dependent Resistor ). Its resist...

Q: 13. Find the rms values of the following sinusoidal waveforms: a. v= 10 millivolts sin (377t + 60) b...

Q: T or F, modify the wrong part if False, please underline twice your answer if True or False. Synch...

A: In this question we will write whether synchronous motor runs at constant speed or not at variable l...

Q: A 400V, 3 - phase, 4 wire, star - connected system supplies three resistive loads of 15kW, 20kW and ...

A: In this question, 3 phase 4 wire system is given. If each phase power is given for only resistive ...

Q: Determine the output for the following timing diagram for a 2-bit mux (assume it has been enabled an...

Q: 1.A long shunt compound generator delivers 100A,250V at rated load. The resistances of the various w...

Q: The electrons in the outermost orbital determine the physical and chemical properties of the element...

A: The electrons in an atom are distribute in different orbits. The electrons in the outermost orbit is...

Q: A. Consider the Common-Source (CS) amplifier shown below. Vo He Cc Rsig CG RL Cs Sketch/draw and pro...

Q: The conductors of a 10 km long, single phase, two wire line are separated by a distance of 1.5m. The...

Q: 20x ix 10 2 8 A 12 8Ω VB Vc VA 1 )1A 5Ω. + +

Q: Bulbs A, B, and C are identical and all glow. to. Order, from highest to lowest, the luminosity of t...

Q: R1 L1 R2 C1 5000 795.77mH 2000 5.53µF V1 R3 300Vrms 60HZ 0° L2 530.52mH

A: Maximum power theorem: This states that in the circuit load resistance is equal to the source resist...

Q: Problem 2: Class E Amplifier Design A schematic of class E amplifier is shown in the figure 2 given ...

A: We are authorized to answer three sub-parts at a time, since you have not mentioned which part you a...

Q: 122 RL V, SW

A: The solution is given below

Q: Design an excess 3 to binary decoder using the unused combinations of the code as don’t care conditi...

Q: How do you find the transformer rated current when given the current ratios for both the high voltag...

A: Transformer- Transformer is a passive component which transfers electrical energy or electrical sign...

Q: For the coupled coils in (Figure 1), exciting coil 2 from a time-varying current source and leaving ...

A: Two figures are shown coupled coils. We need to derive the equation of coefficient of coupling in te...

Q: For a zener voltage regulator for the given circuit if Vin 30 V constant calculate the range of load...

A: I am answering first question as per the guidelines.

Q: ww Problem 5. Determine the value of Vo 42 ww ww 32 3k2 ASI USS°A

A: The solution is given below

Q: 1. a. Using the characteristics of Fig. 152b, determine Ip, Vp, and Vr for the circuit of Fig. 152a....

Q: 3. Two point charges q, = 2.2nC and q2 = -1.5nC are 13 cm apart. Point A is midway between the charg...

Q: • T or F, modify the wrong part if False, please underline twice your answer if True or False. An ...

A: The given statement. An asynchronous motor is a self-starting machine. Check the given Statment is...

Q: Design a center-tapped full-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate i...

Q: A certain silicon UJT has an intrinsic standoff ratio of 0.58. This UJT is used in an experimental c...

A: Given Vp= 14.09 v x=0.58 Assume cut off voltage Vc= 0.6v Find VBB=?

Q: The primary to secondary turns ratio of a transformer used in a HWR is 20:1. The primary is connecte...

A: The solution is given below

Q: Si 4.7 k2 Ge Si 1.2 k2 +12 Vo -10 Vo GaAs 3.3 kS (a) (b) FIG. 2.159 Problem 9.

Q: Design Half-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate its transformer p...

Q: 3. For a parallel circuit of 20 ohms resistor and a 10 ohms inductor, is connected to a 110/60 cps V...

A: We need to find out current for given circuit

Q: Since the construction of DC generators and Alternators are similar, you can convert a DC generator ...

Q: ELECTRONIC CIRCUIT ANALYSIS AND DEVICES

Q: GENERAL SAFETY RULES FOR ELECTRICITY AND ELECTRONICS Safe practices will protect you and your fellow...

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you ar...

Q: A half wave rectifier develops 10 V dc. What is the value of the ripple voltage? Vr(rms)=Blank 1 V

A: Ripple voltage = sqrt (rms voltage 2- average voltage2). For half wave rectifier average output volt...

Q: 7. Determine the base voltage VB in the circuit. If RE is doubled, what will be the value of VB? +15...

A: As per our company guidelines we are supposed to answer only first question kindly repost other ques...

Q: T or F, modify the wrong part if False, please underline twice your answer if True or False. Th...

A: In this question we will write relation between field flux and current in dc series motor....

Q: A 415V TPN busbar rising main chipped to a surface is to provide a 240V supply to each of 8 individu...

A: Answer - Following is the circuit arrangement showing how each flat must be connected to the rising ...

Q: A compound motor develops a torque of 271 lb-ft when it is operating at 1200 rpm, under which condit...

Q: For a shunt-wound DC motor, all copper losses are considered variable losses

Q: Calculate the current and voltage drop in each resistor.

Q: EX :(10):- A complex low-pass signal has a bandwidth of 1200 kHz. What is the minimum sampling rate ...

Concept explainers

Three Phase Induction Motor

The induction motor is an electric motor that runs on AC (alternating current) and it is of two type single phase motor that work on single-phase power supply and three-phase motor that work on three-phase power supply.

Question

013: Choose the correct answer:
1. In a symmetrical three phase system the total instantaneous three phase power is:
a. Pulsating sinusoidally with frequency o.
b. Pulsating sinusoidally with frequency 30.
c. Constant.
2. It is impossible to obtain analytical solutions for the power flow equations,
because:
a. The number of equations is large.
b. The equations are nonlinear.
c. The number of unknown variables in the equations is large.
3. Stability requirements limit the power-handling capability of:
a. Long lines.
b. Short lines.
c. Medium
4. Bundling of conductors in a transmission line reduces the risk for corona. Also,
it:
a. Reduces the sag of the line.
b. Increases the resistance of the line.
c. Increases the transmission capacity.
5. A 50 Hz, turbo generator supplying 40% of its maximum power capability to 0.8
pu load. The operating power (torque) angle 8° is:
a. 6°=36 elec. deg.
b. 8°= 23.57 elec. deg.
c. 8°-40 elec. deg.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

While the instantaneous electric power delivered by a single-phase generator under balanced steady-state conditions is a function of time havi ng two components of a constant and a double-frequency sinusoid, the total instantaneous electric power delivered by a three-phase generator under balanced steady-state conditions is a constant. (a) True (b) False
The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with a capacitive reactance XC=25. Calculate (a) the instantaneous power absorbed by the resistor, (b) the instantaneous power absorbed by the capacitor. (c) the real power absorbed by the resistor, (d) the reactive power delivered by the capacitor, and (e) the load power factor.
The total instantaneous power absorbed by a three-phase motor (under balanced steady-state conditions) as well as a balanced three-phase impedance load is (a) A constant (b) A function of time
1-Which function we call for three phase short circuit occurs in synchronous generator armature terminals at no load condition a.symshort b.lgfault c.llfault d.symfault 2-The FACTS devices support to control a.susceptance b.reactive power c.real power d.apprant power
Please answer all subparts for like either dislike is ready at least 5 subparts... A 3-phase, 450 V, 2-pole, 50 Hz, wye-connected, synchronous alternator. Xs = 1.62 ohm/phase. Connected to an infinite bus and supplies 120 kW with a power angle of 35 degrees.Neglect losses and find:a. turbine torque supplied to alternator.b. excitation voltage.c. active, reactive power and machine power factor.d. neglecting saturation effects of the field, the excitation voltagee. if the field current is reduced to 80% of its original value in part a.f. the turbine speed for 60 Hz operation.
A Turgo type hydro-electric plant uses a 92% efficiency generator to produce its rated output of 32.5 MW. It was observed during its operation that the mechanical loss is 4.25 MW. Also, from the penstock down to the turbine, 14.3% hydraulic head loss and 8.9% leakage loss occurs which are equally distributed and based on the parameters at the dam. The average elevation from the headrace to the jet centerline is 40 m and from the tailrace to the jet centerline is 4.5 m. compute the following: a. Power by the turbine, kW b. Volume flow rate at the source, m3/s c. Power by the jet, kW d. Mechanical Efficiency, %
Which of the following is more likely to cause problems with motors? a) positive sequence harmonics, b) negative sequence harmonics, c) either a or b, d) neither a nor b in a inductive circuit, does the inductance have any effect on the flow of steady current? a) yes , b) no The rotating part of the revolving-field design alternator is called the rotor. a)true, b) false
A single phase autosequential CFI is fed from a 220 Vde source, R_{L} = 10Omega the thyristor turn off tq time equals to 20 us and frequency is 50 Hz. Determine suitable value of source inductance assuming a maximum current change di/dt of 0.5A per cycle. Neglecting all losses, calculate able the value of operating capacitor C.
For single phase ac voltage controller, R=15ohm, f=50Hz and Vrms=230V and α=0,82 rad. Calculate the rms load voltage (V). In this question, take 2 digits after the comma and take pi = 3,14; enter your answer into the system in terms of the desired unit only as a number.solve the question by using the rules of power electronics
synchronous generator operating under steady conditions supplying a load current I0to the bus at a terminal voltage of V0. E, is the induced emf under loaded condition and Xa is the direct axis synchronous reactance of the machine. Draw the equivalent circuit model of the system.
In a Three-phase alternator, a given field current produces an armature current of 250 A on short-circuit and a generated e.m.f. of 1500 V on open-circuit. Calculate the terminal p.d. when a load of 250 A at 6.6 kV and 0.8 p.f. lagging is switched off. Calculate also the regulation of the alternator at the given load. Subject: Electrical engineering
Consider the following power system model with the following entities:i. A generator generates a sinusoidal waveform with amplitude of 300 V and angular frequency of 5 radians,ii. The transmission line has a resistance of 1Ω, andiii. A capacitive load with a value of 2F presents at the end of the system. Answer the following questions:(a) Draw the relevant diagram and label all entity values of the power system as described above.(b) Replacing the real source in Figure from part (a) with a complex source, find the response of the steady-state capacitor voltage in time-domain.(d) Repeat the sub-question (a) above, now showing calculations in s-domain.