AI200 kN-T43 mm x 43 mm square cross-sectionL….[0,149 mm]2.15 The bar shown below must carry a tensile load of 200 kN. Calculate thediameter of the middle portion if the maximum stress is limited to 200 MPa. Ifthe total extension of the bar under the 200-kN load must not exceed 0,22 mm,calculate the length of the middle portion (take E as 200 GPa).HUAWEI P smart 202148MP QUAD CAMERAFigure 2.20250 mmo 'd'Figure 2.213$ 30 mmIA[35,68 mm; 187,76 mm]2.16 A cable consists of a steel wire, 2,5 mm in diameter, surrounded by six bronzewires of the same size. If the allowable stress in the bronze is 60 MPa, find thesafe load for the cable and the extension under this load on a length of 30 m(Esteel = 200 GPa and Ebronze = 80 GPa).|50 mm45 mm200 KN12.503 kN: 225 mmlW11°C ^

Answered: Image /qna-images/answer/8dac30fd-4231-421d-944b-123492efe487.jpg

[0,149 mm] 2.15 The bar shown below must carry a tensile load of 200 kN. Calculate the diameter of the middle portion if the maximum stress is limited to 200 MPa. If the total extension of the bar under the 200-kN load must not exceed 0,22 mm, calculate the length of the middle portion (take E as 200 GPa). 200 KN 43 mm x 43 mm square cross-section 250 mm o 'd' Figure 2.21 50 mm 45 mm 200 KN [35,68 mm; 187,76 mm]

[0,149 mm] 2.15 The bar shown below must carry a tensile load of 200 kN. Calculate the diameter of the middle portion if the maximum stress is limited to 200 MPa. If the total extension of the bar under the 200-kN load must not exceed 0,22 mm, calculate the length of the middle portion (take E as 200 GPa). 200 KN 43 mm x 43 mm square cross-section 250 mm o 'd' Figure 2.21 50 mm 45 mm 200 KN [35,68 mm; 187,76 mm]

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Similar questions

- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A spherical steel pressure vessel (diameter 500 mm, thickness 10 mm) is coated with brittle lacquer that cracks when the strain reaches 150 X 10~ (see figure). (a) What internal pressure p will cause the lacquer to develop cracks? (Assume E = 205 GPa and v = 0.30.) (b) If the strain is measured at 125 x 10-6, what is the internal pressure at that point?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
With a thick walled cyclinder the inner radius is 0.05m and out radius is 0.2m. The internal pressure is 200 MPa - What is the hoop and radial stress at the inner surface? - What would be a suitaable material for the cyclinder under von mises criterion?
A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200 kPa. If the staves are bound by steel flat bands (10 cm by 2.50 cm), find the spacing of the bands if its allowable stress is 105 MPa.\ Please explain the steps and formulas used.
To support a tensile load of 65 kN, a circular cross section and A metallic rod with a length of 0.32 m will be used. Stress in bar 240 MPa value and maximum elongation is desired to be 0.42 mm. In these conditions,what is the minimum diameter of rod [m]?(Elasticity for metallic bar Take the module as 220 GPa).
Calculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and 118 MPa in steel if a homogeneous 778 000 g bar AB is supported at either end by a cable.
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 mis under tension. If the wire length extension is 2.5 mm, calculate the stress in thewire. Give your answer in N/m2to 2 decimal places.
A very fine fabric 0.020 mm in diameter can support a 20 g object. How does the stress in the fabric compare with the ultimate strength in tension of copper
To support a tensile load of 65 kN, a circular cross section and A metallic rod with a length of 0.32 m will be used. Stress in bar 240 MPa value and maximum elongation is desired to be 0.42 mm. In these conditions, at least What is the (minimum) rod diameter [m]?(Elasticity for metallic bar Take the module as 220 GPa).
A sign of mass 2,500-Kg hangs from the bottom end of a vertical cylindrical aluminum bar (with a diameter of 12-cm). (a) What is the stress within the bar? (b) What is the bar’s strain? (c) If the bar is 10-m long, how much is it lengthened?
A 12-mm thick steel tire has a width of 110 mm and internal diameter of 800 mm. It is heated and trunk onto a steel will 800.50 mm in diameter. The modulus of elasticity of steel is 200 GPa. 1) Which of the following most nearly gives the tensile stress in the tire. a. 145 MPa b. 130 MPa c. 110 MPa d. 125 MPa 2) Which of the following most nearly gives the compressive pressure between the tire and the wheel. a.) 4.35 MPa b.) 3.30 MPa c.) 3.90 MPa d.) 3.75 MPa 3) If the tire has an allowable tensile stress of 124 MPa and is to resist a pressure of 1.50 MPa, which of the following most nearly gives its thickness. a.) 4.84 mm b.) 2.42 mm c.) 2.58 mm d.) 5. 16 mm