04/ For the network in Fig.4 1. Write the equations necessary to solve for the branch currents. 2. By substitution of Kirchhoff's current law, reduce the set to three equations. 3. Rewrite the equations in a format that can be solved using third-order determinants. 4. Solve for the branch current through the resistor R3. R₁ R₂ R₂ 1₂ www W www 40 20 30 E₁30V &50₂6v R₂ 80

04/ For the network in Fig.4 1. Write the equations necessary to solve for the branch currents. 2. By substitution of Kirchhoff's current law, reduce the set to three equations. 3. Rewrite the equations in a format that can be solved using third-order determinants. 4. Solve for the branch current through the resistor R3. R₁ R₂ R₂ 1₂ www W www 40 20 30 E₁30V &50₂6v R₂ 80

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter22: Magnetism

Section: Chapter Questions

Problem 15CQ: Draw a sketch of the situation in Figure 22.30 showing the direction of electrons carrying the...

See similar textbooks

Similar questions

Verify than the direction of the line force in an MHD drive, such as that in Figure 22.32, does not depend on the sign of the charges carrying the current across the fluid.
Draw a sketch of the situation in Figure 22.30 showing the direction of electrons carrying the current, and use RHR-l to verify the direction of the force on the wire.
Integrated Concepts (a) An aluminum power transmission line has a resistance of 0.0580/km. What is its mass per kilometer? (b) What is the mass per kilometer of a copper line having the same resistance? A lower resistance would shorten the heating time. Discuss the practical limits to speeding the heating by lowering the resistance.
A velocity selector in a mass spectrometer uses a 0.100T magnetic field. (a) What electric field strength is needed to select a speed of 4.00106m/s ? (b) What is the voltage between the plates if they are separated by 1.00 cm?
Integrated Concepts One long straight wire is to be held directly above another by repulsion between 1heir currents. The lower wire carries 100 A and the wire 7.50 cm above it is 10gauge (2.588 mm diameter) copper wire. (a) What current must flow in the upper wire, neglecting the Earth’s field? (b) What is the smallest current if the Earth’s 3.00105T field is parallel to the ground and is not neglected? (c) Is the supported wire in a stable or unstable equilibrium if displaced vertically? If displaced horizontally?
. The generator at a large power plant has an output of 1,000,000 kW at 24,000 V. (a) If it were a DC generator, what would he the current in it? (b) What is its energy output each day—in joules and in kilowatt—hours? (c) If this energy is sold at a price of 10 cents per kilowatt-hour, how much revenue does the power plant generate each day?
An x-ray tube used for cancer therapy operates at 4.0 MV, with a beam current of 25 mA striking the metal target. Nearly all the power in the beam is transferred to a stream of water flowing through holes drilled in the target. What rate of flow, in kilograms per second, is needed if the rise in temperature (T) of the water is not to exceed 50.C?
Integrated Concepts A light-rail commuter train draws 630 A of 650-V DC electricity when accelerating, (a) What is its power consumption rate in kilowatts? (b) How long does it take to reach 20.0 m/s stalling from rest if its loaded mass is 5.30 1()4 kg, assuming 95.0% efficiency and constant power? (c) Find its average acceleration. (d) Discuss how the acceleration you found for the light-rail train compares to what might be typical for an automobile.
A hypothetical current flowing in the z-direction creates the field B=C[(x/y2)i+(1/y)j] in the rectangular region of the xy-plane shown in the accompanying figure. Use Ampere’s law to find the current through the rectangle.
Unreasonable Results (a) What current is needed to transmit 1.00 102MW of power at 480 V? (b) What power is dissipated by the transmission lines if they have a 1.00 -resistance? (c) What is unreasonable about this result? (d) Which assumptions are unreasonable, or which premises are inconsistent?
A GFI may trip just because the live/hot and neutral wires connected to it are significantly different in length. Explain why.
A motor operating on 240 V electricity has a 180 V back emf at operating speed and draws a 12.0 A current. (a) What is its resistance? (b) What current does it draw when it is first started?