Solve completely and support your solution with diagrams or figures. 04. A water in a tank is pressurized by air the pressure is measured by a fluid manometer.Determine the gage pressure of air in tank if h:=0.2 m, h2=0.3 m, ha=0.46 m. Densities: oil=850kg/m, mercury=13,600 kg/m.OilAirWaterMercury

Given data h1=0.2m h2=0.3m h2=0.46m ρo=850kg/m3ρm=13600kg/m3

Answered: 04. A water in a tank is pressurized by…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

18 - A cylindrical tank with a diameter of 20 cm and a height of 50 cm was filled with water to a height of 30 cm. If the tank is rotated about the vertical axis of symmetry at a constant speed of 21 rad/s, what will be the pressure difference between the bottom center and bottom edge of the tank? a) 1750 Pa B) 1045 Pa NS) 3327 Pa D) 2205 Pa TO) 1125 Pa
What is the purpose of calibrating the "spirit bubble" or "spirit level"? O It can measure relative atmospheric pressure O It indicates the measurement uncertainty of the analytical balance O It serves as the reference for specific gravity O It is necessary to maintain an even surface when measuring mass
PROBLEM 5: The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown. Determine the gage pressure of air in the tank if h1 = 0.4 m, h2 = 0.6 m, and h3 = 0.8 m. Take the densities of water, oil, and mercury to be 1000, 850 , and 13,600 kg/m^3, respectively.
pressurea are sometimes determined by measuring the height of a column of liquid in a vertical tube, what diameter clean glass tubing is required so that the rise of the water at 20°C in a tube due to capillary action (as opposed to pressure in tube) is less than h=1.0mm
In a user’s manual accompanying an American-madeautomobile, a typical gauge pressure for optimal performance of automobile tires is What is thispressure in grams per square centimeter and kilograms per square meter?
Question 6 Figure 6 shows a U-tube manometer.Fluid A is oil ( s= 0,9) and fluid B is mercury (s= 13,6).Determine the prrssure difference between P and Q.Ignore thr density of air.
A fluid with a vapor pressure of 0.2 Pa and a specific gravity of 12 is used in a barometer. If the fluid's column height is 2 m, what is the atmospheric pressure?
Q1 Determine the minimum size of glass tubing that can be used to measure water level, if the capillary rise in the tube is not to exceed 0.3 mm. Take surface tension of water in contact with air as 0.0735 N/m. A U-tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively. Q2) The tube is held vertical and partially filled liquid of surface tension 0.06 N/m and zero contact angle. If the estimated difference in the level of two menisci is 15 mm, determine the density the liquid. Q10) In measuring the unit energy of a mineral oil (specific gravity = 0.85) by the bubble method, a tube having an internal diameter of 1.5 mm is immersed to depth of 12.5 mm in oil. Air is forced through the tube forming a bubble at the lower end. What magnitude of the unit surface energy will be indicated by a maximum bubble pressure intensity of 150 N/m.
In general term, ______________ is the tendency of one fluid to spread on to a solid surface in the presence of other fluid a. Relative Density b. Porosity c. Permeability d. Viscosity e. Wettabilty
A mercury manometer (? = 13,600 kg/m3) is connected to an air duct to measure the pressure inside. The difference in the manometer levels is 10 mm, and the atmospheric pressure is 100 kPa. (a) Judging from Fig determine if the pressure in the duct is above or below the atmospheric pressure. (b) Determine the absolute pressure in the duct.
Absolute pressure is the actual existing pressure, independent of the environment, while gauge pressure is the pressure relative to the exterior environment, which is usually the atmosphere (with a pressure of 1 atm). Convert an absolute pressure of 7.25 × 105 N/m2 to gauge pressure, in pounds per square inch. Pg= ?
4. In a condenser containing air and water, the air pressure is 22 kpa absolute. What is the gage pressure in kpa at a point 1.5 m below the water surface

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

04. A water in a tank is pressurized by air the pressure is measured by a fluid manometer. Determine the gage pressure of air in tank if h:=0.2 m, h2=0.3 m, h3=0.46 m. Densities: oil=850 kg/m, mercury=13,600 kg/m2.