08 In ASTM C566-19 or the Standard Test Method for the Total Evaporable Moisture * Content of Aggregate by Drying, the entrapped moisture or water within the voids of the aggregates is also being considered in section 8.1 of the standard. OYes O No From the following sampling procedures that may be employed in the field. which of them can best ensure that the sample will be the best representation of the nature and condition of the materials being sampled? Assume that the material is fine aggregate. You can select more than one. Flowing Aggregate Stream (Bins or Belt Discharge) Transportation Units Conveyor Belt Stockpiles Arrange the following steps in sequence in performing C136/C136M-19. (1) Select sieves with suitable openings. (2) Dry the sample to constant mass. (3) Continue sieving for a sufficient period. (4) Determine the mass of each size increment. (5) Limit the quantity. O 2,1,5,4,3

08 In ASTM C566-19 or the Standard Test Method for the Total Evaporable Moisture * Content of Aggregate by Drying, the entrapped moisture or water within the voids of the aggregates is also being considered in section 8.1 of the standard. OYes O No From the following sampling procedures that may be employed in the field. which of them can best ensure that the sample will be the best representation of the nature and condition of the materials being sampled? Assume that the material is fine aggregate. You can select more than one. Flowing Aggregate Stream (Bins or Belt Discharge) Transportation Units Conveyor Belt Stockpiles Arrange the following steps in sequence in performing C136/C136M-19. (1) Select sieves with suitable openings. (2) Dry the sample to constant mass. (3) Continue sieving for a sufficient period. (4) Determine the mass of each size increment. (5) Limit the quantity. O 2,1,5,4,3

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter8: Landfills

Section: Chapter Questions

Problem 8.9P

See similar textbooks

Similar questions

please explain sampling from a static slurry
A Shelby tube sampler has an outside diameter (O.D.) of 4.00 inches and a thickness of 1/16 in. What is the area ratio? Is it better to push or drive this sampler if sampling disturbance is to be minimized? Please give full answer
Define the types of piston sampler ?
For groundwater sampling in monitoring wells, what procedures for installing the well are necessary to ensure that the depth indicated for the water sample is accurate?
What is a Stausseheibe or S-iype pitot tube and why is it used for stack sampling?
Why was the field sample test method developed? Name the three methods for reducing field sample.
Flocculation is very important in dewatering process. With special reference to the standard operating procedure, show step by step on how to conduct settling tests in a laboratory space.
Geotechnical Engineering (UPVOTE WILL BE GIVEN. PLEASE ANSWER THE QUESTION CORRECLTY. NO LONG EXPLANATION NEEDED. FOLLOW THE INSTRUCTIONS CAREFULLY.) A moist soil weighed 895 g with a volume of 425 cm3. After drying, the sample weighed 775 g. Of the dried soil, 400 g was poured into a vessel loose state. Its volume subsequently determined to be 275 cm3. That same 400 g was then vibrated and tamped to a volume of 212 cm3 with Gs = 2.71. Determine the designation of the granular soil based on its relative density. (3 decimal places - Do not round off unless it's the final answer)
Geotechnical Engineering (UPVOTE WILL BE GIVEN. PLEASE ANSWER THE QUESTION CORRECLTY. NO LONG EXPLANATION NEEDED. FOLLOW THE INSTRUCTIONS CAREFULLY.) A moist soil weighed 895 g with a volume of 425 cm3. After drying, the sample weighed 775 g. Of the dried soil, 400 g was poured into a vessel loose state. Its volume subsequently determined to be 275 cm3. That same 400 g was then vibrated and tamped to a volume of 212 cm3 with Gs = 2.71. a. Determine the relative density of soil in %. b. Determine the designation of the granular soil based on its relative density.
a layer of soil in a tube that is 100mmx 100mm in cross section. Water is supplied to maintain a constant head dierence ot a ocross the sample. The height of each soil sample is 100mm. Knowing that the thiree soll sample were having the sanme length the distane of point B to Ais 300mm. Calculate the eguivalent kin cm/sec from point A to B if k1 k2. and k3 is equal to 1x10 cm/se. 3x10 cm/sec and-4.9x10cm/ser espee
Describe the concept of Gas-driven water samplers.
a) With the aid of relevant equations explain what is meant by "settling ratio" b) Explain the difference between free settling and hindered settling c) Why is sizing helpful for gravity concentrator feed to have a narrow particle size distribution? d) The shaking table is frequently used for final concentration of gold. Describe this unit showing how operating variables can be adjusted to optimise its performance