Answered: 1-54 In the dimensionally homogeneous…

1-54 In the dimensionally homogeneous equation Wo? u = Fd – 2g F is a force, W is a force, d is a length, and v is a linear velocity. Determine the dimensions of U and g.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.46P

See similar textbooks

Related questions

Q: The sketch shows an oil manometer that is connected between two pipes which transport water. The…

A: Given, h1=0.17 mh2=350 mm=0.35 mh3=15 cm=0.15 m The specific gravity of the oil, γo=0.76 The density…

Q: 1-59 The equation x= Ae t sin (at + a) is dimensionally homogeneous. If A is a length and t is time,…

Q: 1-56 In the dimensionally homogeneous equation Pd= mv2 + d is a length, m is a mass, v is a linear…

A: For a dimensionally homogeneous equation the unit of LHS must be equal to the RHS unit. The…

Q: approximated 101.325 (1 1-110 The average atmospheric pressure on earth is as a function of altitude…

A: Given data: Patm=101.3251-0.02256z5.256 Need to determine the atmospheric pressure at Atlanta,…

Q: 1.20 Express the following quantities in SI units: (a) 10.2 in./min, (b) 4.81 slugs, (c) 3.02 lb,

A: Given data, a) 10.2 in/ min b) 4.81 slugs c) 3.02 lb

Q: 1-Density is commonly expressed in units of moles per cubic centimeter. 2-Hydrometer: an instrument…

A: The following question is true or false. The answers are given with explanation-

Q: Aside from the movable wire setup, another method to determine the surface tension of a fluid is by…

A: Answer: The surface tension of the liquid is 0.0502 N/m.

Q: Q1/ The physical change in dimensions of the material and its state as a result of an increase in…

A: Thermal expansion is the tendency of matter to change in shape, volume, and area in response to…

Q: 1. Find the density of an oil filled in the liquid column as shown in figure. Given that absolute…

Q: 1-75 Consider a double-fluid manometer attached to an air pipe shown in Fig. Pl-75. If the specific…

A: The manometer is used to measure fluid pressure. It is most accurate while measuring low fluid…

Q: 1- The thrust (P ll i) of a propeller depends upon diameter (D); speed (u) through a fluid density…

A: The dimensional formula for each is as shown below.

Q: 1-62 Determine the dimensions of c, », k, and P in the |differential equation d²x dx +c- dt + kx = P…

A: The given differential equation is – There are four terms in the above equation, hence every term…

Q: 1. Find the density of an oil filled in the liquid column as shown in figure. Given that absolute…

Q: 1-20. Determmine a set of three rectangular compo- nents of the 242-lb force shown in Fig. P1-20. 2…

Q: *1-4. Represent each of the following combinations of units in the correct SI form: (a) Mg/ms, (b)…

Q: *1-8. If a car is traveling at 55 mi/h, determine its speed in kilometers per hour and meters per…

Q: 1-41. The velocity profile of a Newtonian fluid flowing over a fixed surface is approximated by u =…

A: Newton's law of Viscosity: Newton's law of viscosity states that shear stress varies linearly with…

Q: 3.05 m T35° 27.2 kg

A: m=mass of the child = 27.2 kgθ= 35°θ˙=2 rad/sL=length from child to point O=3.05 m

Q: How much work is done in forcing 50 ft3 of water through a 0.5-inch pipe if the difference in…

A: GivenQ=50ft3dameter of pipe d=0.5inpressure difference ∆P=15lbs/in2

Q: *1-20. Evaluate each of the following to three significant figures and express each answer in SI…

Q: 1-54 The diameters of the pistons shown in Fig. P1-54 are Di ber 3, in kPa, when the other pressures…

Q: 1. Find the density of an oil filled in the liquid column as shown in figure. Given that absolute…

Q: The value of G (universal gravitational constant) used for engineering computationsin the U.S.…

Q: Each of the three circular containers in the figure contain a liquid with a SG of 1.37. What is the…

Q: 1-72 The maximum blood pressure in the upper arm of a healthy person is about 120 mmHg. If a…

Q: The specific gravity of the substance is 0.75. A substance has a mass of 25 kg and a volume of 6…

Q: A container is hoisted upward at constant velocity as shown in figure below. Given Container weight…

A: Given Data The weight of the container is: W=417 N The angle is: θ=21° To Determine Force acting…

Q: 1-61 Determine the dimensions of a, b, c, and y in the dimensionally homogeneous equation y = Ae-M…

Q: *1-16. The tanker carries 858(10³) barrels of crude oil in its hold. Determine the weight of the oil…

A: Data given in question: S.G = 0.940 volume of crude oil V=858(103)*159 litre = 858*159 m3…

Q: 1- What are the Lachrange equations for the particle in the given figure? A) L=mR-0² – mgRcos0 B) L=…

Q: An object is to be measured using a basic barometer. If the reading at the top is 725.54 mm and at…

Q: ed with using an oil of specific gravity 0.8. Find the dynamic viscosity and kinematic viscosity of…

Q: 2-25. As the balloon ascends, measurements indicate that the temperature begins to decrease at a…

Q: The density of air at standard room conditions is 1.2 kg/m³. Express the density in U.S. customary…

Q: 1- What are the Lachrange equations for the particle in the given figure?. A) L=mR*6² – mgRcos0 B)…

Q: 1. Write down the definiton of following with their units in standard scientific notation. a)…

A: Dear student, According to the guidelines I am allowed to answer only three…

Q: The power, P, produced by a wind turbine is given by: P = (%) CPAV³ where p is the density of air…

A: Power is defined as work per unit time

Q: 1-10. What is the weight in newtons of an object that has a mass of: (a) 10 kg, (b) 0.5 g, and (c)…

A: given data - gravitational acceleration, g = 9.81 m/s2 to determine- weight of different objects in…

Q: The displacement of a particle is given by s = 3t3 - 40t2 + 94t - 47 where s is in feet and t is in…

Q: 1-88 When a body moves through a fluid it experiences a resistance to its motion which can be…

A: The force experience a resistance when the body is in fluid is given as, F=12CDρV2A.......(1) Here,…

Q: 1-53 The water in a tank is pressurized by air, and the pres- sure is measured by a multifluid…

A: Given figure The water in a tank is pressurized by air, and the pres sure is measured by a…

Q: 20 Ibf 02) Given the figure attached, Determine the following: 200 kg 250 N • 1) What is magnitude…

A: Solution to first three sub-parts as per out company policy:

Q: 1-82* Atwhat distance from the center of the earth would the force of attraction between two spheres…

A: Given Data: The mass of each sphere is m = 250 kg. The diameter of each sphere is D = 1 m. The…

Q: 1000N

A: Calculated reaction force in vertical and horizontal direction.

Q: 70 40* 1.10 m 2.00 m 1.25 m

A: (a) The center of gravity of the beam will be at the center of the beam which is shown below –

Q: 3-41. A person's blood pressure is identified by the ratio of the maximum pressure (systolic…

Q: 1-41. The velocity profile of a Newtonian fluid flowing over a fixed surface is approximated by u =…

Concept explainers

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.

Question

1-54 In the dimensionally homogeneous equation
Wo?
u = Fd –
2g
F is a force, W is a force, d is a length, and v is a linear
velocity. Determine the dimensions of U and g.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The value of G (universal gravitational constant) used for engineering computationsin the U.S. system of units is G = 3.439(10- 8) ft3/(slug · s2). Use theconversion factors listed in Table 1-6 to determine a value of G with units ofm3 I (kg · s2) suitable for computations in the SI system of units.
Determine the temperature of air in °C if the pressure is at 855 kPa and the specific volume is 0.1 m3/kg. Report your answer to nearest whole number using rounding
1. What is the weight in pounds-force of an object with a mass of 19 lbm on a planet where g = 12 ft/s2? 2. If a gas has γ = 14 N/m3, what is its density? State your answers in SI units.
Please don't copy,Solve in handwritten format only. The gauge pressure in the air container in Fig. P1-83 is 80kPa . Calculate the differential height h of the column of mercury.
Another unit is kgf, which is a force unit used mostly in Europe, and is defined as kp (kilopond). Explain the difference between kilopond (kp = kgf) and kilopound (103 lbf) from force units and write the unity conversion factor between them. The density of water at 4°C is = 1000 kg/m3. Express this density value in units of kp ⋅ m−4 ⋅ s2.
1. A 450 mm ice tube with 0.56ft^3/slug specific volume, melts and filled a spherical container. Determine the diameter of the container in inches. 2. If the sp. Volume of a certain is fluid is 0.7848m^3/kg. What is the specific weight (N/m^3)?
Evaluate the following to three significant figures and express each answer in SI units using an appropriate prefix: (684 mm)(43 ms)
What volume (in m3) of natural gas would it take to generate 5.94 x 108 J of energy if the energy content of natural gas is 36.9 MJ/m3 [round your final answer to one decimal place]?
using excel how can we convert these two 9.81 m/s2 to ft/s2 i. 2000 kg/m3 to lbm/ft3
The air pressure in an automobile tire is 35 psi.Express the pressure in appropriate SI units (kPa) by usingthe values listed in Table 1-6 for length and force as definedvalues
1. Determine the volume of an object that weighs 5 lb in water and 7 lb in oil of specific gravity 0.82. 2. What is the specific weight of the object?
The question is attached as an image. Convert the length of the first part into meters. 0.75 cm = 0.0075 m.