ed with using an oil of specific gravity 0.8. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 663050 cm and weight of 67 kN ITER ONLY THE VALUES BY REFERRING THE UNITS GIVEN) e dynamic viscosity of the fluid (in Centipoise) e kinematic viscosity of the fluid (in stokes)

ed with using an oil of specific gravity 0.8. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 663050 cm and weight of 67 kN ITER ONLY THE VALUES BY REFERRING THE UNITS GIVEN) e dynamic viscosity of the fluid (in Centipoise) e kinematic viscosity of the fluid (in stokes)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.13P: 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its...

See similar textbooks

Similar questions

5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.
A differential equation is d2ydt2=Ay2+Byt where y represents a distance and t is time. Determine the dimensions of constants A and B for which the equation will be dimensionally homogeneous.
A plate 0.05mm distance from a fixed plate moves at 1.25 m/s and required a force per unit area of 3 Pa to maintain this speed by using an oil of specific gravity 0.65. Find the dynamic viscosity in centipoise and kinematic viscosity in stokes of the fluid between the plates. Calculate the specific weight in kN/m³, density, and the specific gravity of a liquid having a volume of 662900 cm and weight of 55 kN
1. Two indefinitely long flat plates separated by 3 inches in distance but with a thickness of 5 inches each carry alcohol (5 m/s, 1 Pa·s, S.G. 0.89 (ref. water at 4 degrees Celsius) to a specific destination. Find out what the Reynolds Number is. 2. Calculate the dynamic and kinematic viscosities of water at 350 degrees Kelvin Note: Use perry's handbook for the value
C1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 2.2 N/m2 to maintain this speed with using an oil of specific gravity 0.75. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. C1 (b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 665000 cm3 and weight of 72 kN find : C1 (a) 1_The dynamic viscosity of the fluid (in Centipoise) 2_The kinematic viscosity of the fluid (in stokes) C1 (b) 3_Specific Weight in (N/m3) 4_Density of liquid (in kg/m3) 5_Specific gravity of liquid
Light diesel oil at 15 ℃ Relative density (specific gravity) is 0.80, Kinematic viscosity is 5×10^-5 m2/s. What is Specific Weight, Density and dynamic viscosity?
C1 (a). A lubricating oil having the dynamic viscosity of 0.055 poise and kinematic viscosity of 0.17 stokes. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3,(iii) the specific gravity, and (iv) the specific volume in m3/kg. C1 (b). Calculate the capillary effect in mm in a glass tube of 4.4 mm diameter, when immersed in (1) water (2) mercury. The values of surface tension in contact with air are 0.0737 N/m and 0.54 N/m respectively. The contact angle for water =00 and mercury =1300. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) C1(a).(i).The density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the specific gravity C1(a). (iv) the specific volume in m3/kg C1 (b). 1.The capillary effect (water) in mm C1 (b). 2.The capillary effect (mercury) in mm
A plate weighing 150 N and measuring 0.8 m ×0.8 m just slides down on inclined plane over which an oil film of 1.2 mm thickness for an inclination of 30° and velocity of 0.2 m/s. Calculate the viscosity of oil.
A tape, of width w = 25.40 mm is to be coated on both sides with a lubricant by drawing in througha narrow gap of length, L as depicted in Figure 2. Following below values are given:c = 0.300 mm, t = 0.381 mm, and L = 20.0 mm.The lubricant, of dynamic viscosity  = 1.0054 kg/m.s completely fills the gap and the velocitydistribution is assumed to linear as shown in Figure 2. The maximum allowable force in the tape isgiven as F = 30.04 N. Find the maximum allowable tape speed
A hydrodynamic journal bearing is subject to 2000 N load at a rotational speed of 2000 rpm Both bearing bore diameter and length are 40 mm. If radial clearance is 20 um and bearing is lubricated with an oil having viscosity 0.03 Pa-s, what is the Sommerfield number of the bearing?
A tape, of width w = 25.40 mm is to be coated on both sides with a lubricant by drawing in throughnarrow gap of length, L as depicted in Figure 2. Following below values are given:c = 0.300 mm, t = 0.381 mm, and L = 20.0 mm.The lubricant, of dynamic viscosity  = 1.0054 kg/m.s completelys fills the gap and the velocitydistribution is asssumed to linear as shown in Figure 2. The maximum allowable force in tape isgiven as F = 30.04 N. Find the maximum allowable tape speed
Air with density of 1.225 kg/m^3 and viscosity of 1.789 x 10^-5 kg/m-s flows in a wind tunnel, the wind tunnel spped is measured with Pitot tube probe. For a certain run, the stagantion pressure is measured to be 472.6 Pa gage and the statric pressure is 15.43 Pa gage. Calculate the wind tunnel speed.