1 Calculate the mass % of the limiting reactant BaCl2 in a salt mixture of mass 1.08 g, knowing that the mass of the precipitate was 0.231 g Ba3(PO4)2 (602 g/mol), Na3PO4.12H2O (380 g/mol), BaC12.2H2O (244g/mol). S 2 Na PO4 - 12H½0 + 3 BaClz 2H;0 Bay(PO)2 + 6 NaCl + 30 H20 O 80 % O 74 % O 26 % 60 %

1 Calculate the mass % of the limiting reactant BaCl2 in a salt mixture of mass 1.08 g, knowing that the mass of the precipitate was 0.231 g Ba3(PO4)2 (602 g/mol), Na3PO4.12H2O (380 g/mol), BaC12.2H2O (244g/mol). S 2 Na PO4 - 12H½0 + 3 BaClz 2H;0 Bay(PO)2 + 6 NaCl + 30 H20 O 80 % O 74 % O 26 % 60 %

Chemistry for Engineering Students

4th Edition

ISBN:9781337398909

Author:Lawrence S. Brown, Tom Holme

Publisher:Lawrence S. Brown, Tom Holme

Chapter4: Stoichiometry

Section: Chapter Questions

Problem 4.87PAE

See similar textbooks

Similar questions

The active ingredient in some antiperspirants is aluminum chlorohydrate, Al2(OH)5Cl. Analysis of a 2.000-g sample of antiperspirant yields 0.334 g of aluminum. What percent (by mass) of aluminum chlorohydrate is present in the antiperspirant? (Assume that there are no other compounds containing aluminum in the antiperspirant.)
A titanium ore contains rutile (TiO2) plus some iron oxide and silica. When it is heated with carbon in the presence of chlorine, titanium tetrachloride, TiCl4, is formed. TiO2(s)+C(s)+2Cl2(g)TiCl4(g)+CO2(g) Titanium tetrachloride, a liquid, can be distilled from the mixture. If 35.4 g of titanium tetrachloride is recovered from 18.1 g of crude ore, what is the mass percentage of TiO2 in the ore (assuming all TiO2 reacts)?
The principal component of mothballs is naphthalene, a compound with a molecular mass of about 130 amu, containing only carbon and hydrogen. A 3.000-mg sample of naphthalene burns to give 10.3 mg of CO2. Determine its empirical and molecular formulas.
A sample of H2C2O4.2H2O of mass 3.35 g is heated to drive off the waters of hydration (designated separately in the chemical formula). What mass of H2C2O4 remains once the water has been removed by heating?
Disulfur dichloride, S2Cl2, is used to vulcanize rubber. It can be made by treating molten sulfur with gaseous chlorine. S8() + 4 Cl2(g) 4 S2Cl2(g) Complete this table of reaction quantities for the production of 103.5 g S2Cl2.
4.79 Phosphoric add (H3PO4) is important in the production of both fertilizers and detergents. It is distributed commercially as a solution with a concentration of about 14.8 M. Approximately 2.1 X l09 gallons of this concentrated phosphoric acid solution is produced annually in the United States. Assuming that all of this H3PO4 is produced by the reaction below, what mass of the mineral fluoruapatite (Ca5(PO4)3F) would be required each year? Ca5( PO4)3F+5H2SO43H3PO4+5CaSO4+HF
You take 1.00 g of an aspirin tablet (a compound consisting solely of carbon, hydrogen, and oxygen), burn it in air, and collect 2.20 g CO2 and 0.400 g H2O. You know that the molar mass of aspirin is between 170 and 190 g/mol. Reacting 1 mole of salicylic acid with I mole of acetic anhydride (C4H6O3) gives you 1 mole of aspirin and 1 mole of acetic acid (C2H4O2). Use this information to determine the molecular formula of salicylic acid.
The final step in the manufacture of platinum metal (for use in automotive catalytic converters and other products) is the reaction 3 (NH4)2PtCl6(s) 3 Pt(s) + 2 NH4Cl(s) + 2 N2(g) + 16 HCl(g) Complete this table of reaction quantities for the reaction of 12.35 g (NH4)2PtCl6.
4.108 Elemental analysis is sometimes carried out by combustion of the sample. For a hydrocarbon, the only products formed are CO2 and H2O. If a 1.36-g sample of an unknown hydrocarbon is burned and 2.21 g of H2O is produced along with 4.07 g of CO2, what is the empirical formula of the hydrocarbon?
What is the molarity of each ion present in aqueous solutions of the following compounds prepared by dissolving 28.0 g of each compound in water to make 785 mL of solution? (a) potassium oxide (b) sodium hydrogen carbonate (c) scandium(III) iodite (d) magnesium phosphate
In the thermite reaction, iron(III) oxide is reduced by aluminum to give molten iron Fe2O3(S) + 2 Al(S) 2 Fe(l) + Al2O3(S) If you begin with 10.0 g of Fe2O3 and 20.0 g of AI, (a) Which reactant is limiting? (b) What mass of Fe can be produced? (c) What mass of the excess reactant remains after the limiting reactant is consumed? (d) Set up an amounts table for this problem.
4.85 In the cold vulcanization of rubber, disulfur dichloride (S2Cl2) is used as a source of sulfur atoms, and those sulfur atoms form “bridges,” or cross-links, between polymer chains. S2Cl2 can be produced by reacting molten sulfur (S8(l)) with chlorine (Cl2(g)). What is the maximum mass of S2Cl2 that can be produced by reacting 32.0 g of sulfur with 71.0 g of chlorine?