1-DC-DC Boost Converter is operating in dc steady state under the following conditions: The input voltage (Vin)= 12 V, inductor (L)= 270 μH, capacitor (C)= 20 μF, resistive load (R) 2302, switching frequency (Fsw)= 20 KHz, duty cycle (D)= 0.5 Calculate inductor current ripple and draw the inductor voltage, inductor current waveforms, and the capacitor current waveform?

1-DC-DC Boost Converter is operating in dc steady state under the following conditions: The input voltage (Vin)= 12 V, inductor (L)= 270 μH, capacitor (C)= 20 μF, resistive load (R) 2302, switching frequency (Fsw)= 20 KHz, duty cycle (D)= 0.5 Calculate inductor current ripple and draw the inductor voltage, inductor current waveforms, and the capacitor current waveform?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
The circuit is connected to a 60-Hz line. The apparent power in the circuit is 29.985 VA, and the power factor is 62.5%. The resistor has a voltage drop of 14.993 V, the inductor has an inductive reactance of 60 , and the capacitor has a capacitive reactance of 45 . ETITZVA29.985PF62.5%ER14.993VIRRPELILXL60VARsLLECICXC45VARsCC
Inductive Circuits Fill in all the missing values. Refer to the following formulas: XL=2fLL=XL2ff=XL2L Inductance (H) Frequency (Hz) Inductive Reactance ( ) 1.2 60 0.085 213.628 1000 4712.389 0.65 600 3.6 678.584 25 411.459 0.5 60 0.85 6408.849 20 201.062 0.45 400 4.8 2412.743 1000 40.841
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
Assume that the voltage drop across the resistor, ER, is 78 V; the voltage drop across the capacitor, EC, is 104 V; and the circuit has a total impedance, Z, of 20 . The frequency of the AC voltage is 60 Hz. Find the missing values. ET ER78V EC104V IT IR IC Z20 R XC VA P VARSC PF C
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
A boost converter has the following parameters: output of 30 V from a 12-V source, R = 40 Ω. for continuous inductor current and an output ripple voltage of less than one percent. then the minimum inductance for continuous current is 100 µH. Select one: True False
A buck converter is supplied from a 50V battery source. Given L=400uH, C=100uF, R=20 Ohm, f=20KHz and D=0.4. Calculate: (a) output voltage (b) maximum and minimum inductor current, (c) output voltage ripple
Design a buck converter such that the output voltage varies between from 20V to 28V while the input voltage is 40V. The maximum load power is 200Wde. Assume the switching frequency is 15kHz. (a) Design the converter such that it will be in continuous current mode. (b) The capacitor realized output voltage ripple must not be more than 1% at worst case. (c) The inductance realizes CCM at worst case. (d) Select the appropriate switch and other elements
Design a buck converter that converts input DC 50 V to output 30 V/1 A. (Specifications: Inductor current continuous, output ripple voltage effective 10 mV or less, input 50 Vdc, output 30 Vdc/1 A)