1- In compression, the failure mode is . 2- Shear strength is approximately.. of the uniaxial compressive strength 3- ...... . .defined as the total volume of the overall volume of pores 4- Used air- entraining admixture . .the segregation ......

1- In compression, the failure mode is . 2- Shear strength is approximately.. of the uniaxial compressive strength 3- ...... . .defined as the total volume of the overall volume of pores 4- Used air- entraining admixture . .the segregation ......

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the concrete mix according to the following conditions: Design Environment Building frame Required design strength = 27.6 MPa Minimum dimension = 150 mm Minimum space between rebar = 40 mm Minimum cover over rebar = 40 mm Statistical data indicate a standard deviation of compressive strength of 2.1 MPa is expected (more than 30 samples). Only air entrainer is allowed. Available Materials Air entrainer: Manufacture specification 6.3 ml/1% air/100 kg cement. Coarse aggregate: 19 mm nominal maximum size, river gravel (rounded) Bulk oven-dry specific gravity = 2.55, Absorption = 0.3% Oven-dry rodded density = 1761 kg/m3 Moisture content = 2% Fineness modulus = 2.47
Design the concrete mix according to the following conditions:Design Environment• Building beamo Required design strength = 27.6 MPao Minimum dimension = 150 mmo Minimum space between rebar = 40 mmo Minimum cover over rebar = 40 mmo Statistical data indicate a standard deviation of compressive strengthof 2.1 MPa is expected (more than 30 samples).• Only air entrainer is allowed.• Moderate Sulphate exposure.• Available Materialso Air entrainer:▪ Manufacture specification 6.3 mL/1% air/100 kg cement.o Coarse aggregate:▪ 19 mm nominal maximum size▪ River gravel (rounded)▪ Bulk oven-dry specific gravity = 2.55▪ Absorption = 3.6▪ Oven-dry rodded density = 1761 kg/m3▪ Moisture content = 2.5o Fine aggregate:▪ Natural sand▪ Bulk oven-dry specific gravity = 2.659▪ Absorption = 0.5▪ Moisture content = 2▪ Fineness modulus = 2.47o Cement▪ Type II (Moderate Sulphate Resistant)▪ Specific Gravity = 3.15Based on this information, find the following and summarize the findings in a table d) The amount…
Design the concrete mix according to the following conditions:Design Environment• Building beamo Required design strength = 27.6 MPao Minimum dimension = 150 mmo Minimum space between rebar = 40 mmo Minimum cover over rebar = 40 mmo Statistical data indicate a standard deviation of compressive strengthof 2.1 MPa is expected (more than 30 samples).• Only air entrainer is allowed.• Moderate Sulphate exposure.• Available Materialso Air entrainer:▪ Manufacture specification 6.3 mL/1% air/100 kg cement.o Coarse aggregate:▪ 19 mm nominal maximum size▪ River gravel (rounded)▪ Bulk oven-dry specific gravity = 2.55▪ Absorption = 3.6▪ Oven-dry rodded density = 1761 kg/m3▪ Moisture content = 2.5o Fine aggregate:▪ Natural sand▪ Bulk oven-dry specific gravity = 2.659▪ Absorption = 0.5▪ Moisture content = 2▪ Fineness modulus = 2.47o Cement▪ Type II (Moderate Sulphate Resistant)▪ Specific Gravity = 3.15Based on this information, find the following and summarize the findings in a table.a) Required…
Design the concrete mix according to the following conditions:Design EnvironmentPavement slab, subjected to freezingRequired design strength = 21 MPaSlab thickness = 300 mmStatistical data indicate a standard deviation of compressive strength of1.7 MPa is expected (more than 30 samples).Only air entrainer is allowed.Available MaterialsAir entrainer: Manufacture specification is 9.5 mL/1% air/100 kgcement.Coarse aggregate: 2 in. nominal maximum size, crushed stoneBulk oven-dry specific gravity = 2.573, absorption = 2.8,Oven-dry rodded density = 1922 kg/m3Moisture content = 1,Fine aggregate: Natural sandBulk oven-dry specific gravity = 2.540, absorption = 3.4,Moisture content = 4.5,Fineness modulus = 2.68
Design the concrete mix according to the following conditions:Design EnvironmentBuilding frameRequired design strength = 27.6 MPaMinimum dimension = 150 mmMinimum space between rebar = 40 mmMinimum cover over rebar = 40 mmStatistical data indicate a standard deviation of compressive strength of2.1 MPa is expected (more than 30 samples).Only air entrainer is allowed.Available MaterialsAir entrainer: Manufacture specification 6.3 mL/1% air/100 kg cement.Coarse aggregate: 19 mm nominal maximum size, river gravel (rounded)Bulk oven-dry specific gravity = 2.55, absorption = 3.6,Oven-dry rodded density = 1761 kg/m3Moisture content = 2.5,Fine aggregate: Natural sandBulk oven-dry specific gravity = 2.659, absorption = 0.5,Moisture content = 2,Fineness modulus = 2.47
Design a concrete mix for the following conditions and constraints using the Absolute Volume Method. The material description are as follows: I. Design Environment i. Retaining Wall exposed to moderate sulfate exposure ii. Required Design Compressive Strength = 27.6 MPa iii. Standard Deviation of Compressive Strength of 1.8 MPa is expected (25 sample only) iv. Minimum dimension = 200 mm v. Minimum space between re-bars = 50 mm vi. Minimum cover over re-bars = 50 mm vii. Maximum Slump is required viii. Only air entrained is allowed II. Available Materials i. Air Entrained – Manufacture Specification 5.5ml/1% air/100 kg cement (use maximum or +2% air content) ii. Coarse Aggregates 25 mm Nominal Maximum Aggregate Size Rounded River Gravel (Note: apply water content reduction) Bulk Oven-dry specific gravity = 2.65 Absorption = 0.2%…
Design the concrete mix according to the following conditions: Design environment Tennis court, subjected to freezing Required design strength =21 MPa Slab thickness=300 mm Statistical data indicate a standard deviation of compressive strength of 3.7 MPa is expected (for 50 samples) Only air entrainer is allowed Available materials: Air=7% Air entertainer: Manufacturer specification is 9.0 ML /1% air/100kg cement Slump=50 mm Coarse aggregate: 50 mm nominal maximum size, crushed stone Bulk volume oven-dry specific gravity=2.61, absorption=2.8%, oven-dry rodded density=1870 kg/m3 Moisture content=1% Fine aggregate: Natural sand Bulk oven-dry specific gravity=2.54, absorption=3.4% Moisture content= 4.5% Fineness modulus=2.60 Cement: Type I, relative density=3.1
Answer by true or false for the following: 1-To prevent segregation, the height of free fall of concrete should exceed 1m in any case. * a-True b-False 2-Truck- mixed concrete is completely mixed within the mobile mixer after it has been charged at the central plant. * a-True b-False 3- Shotcreting is used for repairing deteriorated concrete. * a-True b- False 4- The Biaxial loading in compression test represents the most conservative system and yields the lowest values in compression. * a-True b-False 5- The slump of the concrete mix increases as the temperature of the mix increases. * a-True b-False
Please give the correct dolution and answer of this problem in principle of reinforced/presstressed concrete
Concrete Mix Design-ACI Method The concrete will be non-air entrained since the structure is not exposed to severe weathering. Required average strength will be 24 MPa with slump of 75 to 100 mm. The coarse aggregate has a nominal maximum size of 37.5 mm and dry-rodded mass of 1600 kg/m. Other properties of the ingredients are: cement -- Type I with specific gravity of 3.15; coarse aggregate bulk specific gravity 2.68 and absorption 0.5 percent; fine aggregate-bulk specific gravity 2.64, absorption 0.7 percent, and fineness modulus 2.8.
Design the concrete mix according to the following conditions:Design Environment• Concrete slabo Subjected to freeze and thaw.o Required design strength = 21 MPao Slab thickness = 300 mm.o Statistical data indicate a standard deviation of compressive strengthof 1.7 MPa is expected (more than 30 samples).• Only air entrainer is allowed.• Available Materials:o Air entrainer:▪ Manufacture specification is 9.5 mL/1% air/100 kg cement.o Coarse aggregate:▪ 25 mm nominal maximum size▪ Crushed stone▪ Bulk oven-dry specific gravity = 2.573▪ Absorption = 2.8▪ Oven-dry rodded density = 1922 kg/m3▪ Moisture content = 1o Fine aggregate:▪ Natural sand▪ Bulk oven-dry specific gravity = 2.540▪ Absorption = 3.4▪ Moisture content = 4.5▪ Fineness modulus = 2.60o Cement:▪ Type I Cement▪ Specific gravity = 3.15Find the required quantities of cement, water, coarse aggregate, fine aggregate, aircontent, and admixture per 1 m3 of concrete. Summarize the findings in a table.Based on this information, find the…
Design the concrete mix according to the following conditions:Design Environment• Concrete slabo Subjected to freeze and thaw.o Required design strength = 21 MPao Slab thickness = 300 mm.o Statistical data indicate a standard deviation of compressive strengthof 1.7 MPa is expected (more than 30 samples).• Only air entrainer is allowed.• Available Materials:o Air entrainer:▪ Manufacture specification is 9.5 mL/1% air/100 kg cement.o Coarse aggregate:▪ 25 mm nominal maximum size▪ Crushed stone▪ Bulk oven-dry specific gravity = 2.573▪ Absorption = 2.8▪ Oven-dry rodded density = 1922 kg/m3▪ Moisture content = 1o Fine aggregate:▪ Natural sand▪ Bulk oven-dry specific gravity = 2.540▪ Absorption = 3.4▪ Moisture content = 4.5▪ Fineness modulus = 2.60o Cement:▪ Type I Cement▪ Specific gravity = 3.15…