The diameter of a tall stand pipe with an open top is 1.8 m, and the wall thickness is 15 mm. 1. At what water level will the stand pipe's wall experience a 10 MPa circumferential stress? 2. How much axial stress is there in the tank's wall owing to water pressure?

The diameter of a tall stand pipe with an open top is 1.8 m, and the wall thickness is 15 mm. 1. At what water level will the stand pipe's wall experience a 10 MPa circumferential stress? 2. How much axial stress is there in the tank's wall owing to water pressure?

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.2P

See similar textbooks

Related questions

Q: Hanger Rod Bolt Top Yoke- Bottom Strap FIGURE 2

Q: A two span beam subjected to shear and flexure only is reinforced as follows: @ FACE OF SUPPORTS…

Q: A 480-mm-diameter, non-slender, spiral column is symmetrically reinforced with 6-16 mm vertical…

Q: Question 5: (Use a W12 section) Use A992 steel and select a W shape. a. Use LRFD. b. Use ASD. D= 340…

A: LRFD: LRFD means the Load resistance factor design method. The most used method in concrete design…

Q: Question 2* A thin flat plate is immersed in a fluid stream 20 m/s. Estimate the distance x from the…

A: The given data is: Velocity of fluid stream=20 m/s For air, taking ρ=1.2 kg/m3μ=1.8E-5 kg/ms

Q: At the instant shown, cars A and B are traveling at the speeds shown. If B is accelerating at 1036…

Q: 4.7. Water flows at a depth of 2.20 m in a trapezoidal, concrete-lined section (ks = 2 mm) with a…

Q: The distance between two points is 360 m. If the line is to be laid out by 100 m tape which is 0.02…

A: Given data : Correct Length of tape L=100 m Incorrect length of tape L'=100+0.02=100.02 m Incorrect…

Q: Find the altitude of circular cone of minimum volume circumscribed about a sphere of radius x. 5x 6x…

Q: A 200 mm square structural tubing 8 m long is used as a column with the following properties: A =…

Q: The intersection angle of a 10° highway curve is 100°35' and the Point of Intersection (PI) is…

Q: Determine Deflection caused by unit force applied in the direction of unknown is also determined…

Q: A concrete beam has a width of 400 mm and effective depth of 500 mm. It is reinforced at the bottom…

Q: Calculate the nominal shear strength (kN) of 4-legged stirrups 12-mm-diameter, spaced at 240 mm on…

A: Using the formula prescribed by the code the shear strength can be calculated.

Q: 430mm diameter, non-slender, spiral column is symmetrically reinforced with 10-25mm vertical bars.…

A: Spiral column Diameter = 430 mm Asc (compression steel) = 10×(π/4)×252= 4908.75 mm2 Ag=…

Q: The proper method used to determine headwater depth for any culvert problem is to guess the type of…

A: Since, the flow in the culvert is mainly of two types :- Inlet and outlet. Both these flow makes the…

Q: The 2.4-kg package leaves the conveyor belt at A with a speed of vA = 1.5 m/s and slides down the…

A: Find the normal reaction the curved portion of the ramp exerts in N on the package at B

Q: Determine the angular velocity e in rad/s of the radial line OA at this instant if the truck has a…

Q: Determine the maximum shear stress acting in the beam at the section where the internal shear force…

Q: AN AEROPLANE IS FLYING ON A STRAIGHT LEVEL COURSE AT 200 KM PER HOUR AT A HEIGHT OF 1000 METRES…

Q: 410-mm diameter, non-slender, spiral column is symmetrically reinforced with 12-20 mm vertical bars.…

A: Calculate the design strength (kN) of the column

Q: hear and flexure only is reinforcnd as follows: TOP BARS BOTTOM BARS @ MIDSPAN 2-016 mm 3-016 mm @…

Q: e only is reinforced as follows: Given: Stirrup diameter, ds = 10 mm Concrete f'c = 21 MPa Steel…

A: Percentage of steel in tension is less than max.allowable percentage . Consider as a single…

Q: A monolithic floor framing plan is shown in the figure. The columns are 300 mm square, girders are…

Q: A trapezoidal piece of ground is to be divided into two parts in the ration of 2 is to 3 by a line…

A: The given situation is shown below-

Q: A solid steel post is subjected to pure torsion. If the length of the post is 2.5 m, diameter of the…

A: Length L = 2.5 m Diameter d= 75 mm Polar moment of inertia = Ip= (π/32)× d4 Ip= (π/32)× 754=…

Q: 5. A layer of clay, at a depth below the groundwater surface, experiences a rapid increase in…

A: Given data- Increase in pressure ∆p=200 kN/m2coefficient of compression power m=3.8×10-5 m2/kNhere…

Q: ties and tie wire if there are 36 columns with cross section mensions of 60 x 90 cm. at 12.00 meters…

A: Given:- lateral ties dimater=10mm number of columns=36 60 x 90cm L=12.00metres=1200mm To find:-…

Q: A storm sewer inlet collects flow from a with the following characteristics: – Area=4ac. – Land use:…

A: Given, Area (A) - 4 acres Length (L) = 800 ft Slope (Y) = 1%

Q: ead loss between the inlet and of the velocity head, and the he pipe itself between point B of the…

Q: The atmosphere is stable with a lapse rate of -0.2 °C/100 m. The surface air temperature is 15 °C. A…

Q: A train which is traveling at 80 mi/h applies its brakes as it reaches point A and slows down with a…

Q: SITUATION. A soil in its natural state has a moisture content of 30% and a unit weight of 16 kN/m3.…

A: Calculate Void ratio of soil sample,e=?

Q: simply supported beam 300 mm wide, 500 mm deep and spans 5.5 m supports a service super imposed dead…

Q: Calculate the nominal shear strength (kN) of 4 - legged stirrups 12 - mm - diameter, spaced at 230…

Q: In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) =…

Q: Find the strain original length=100 mm Change in length3D0.05 mm

A: The given question is related with solid mechanics . In this question we are provided with value of…

Q: 0.2 Draw the shear and moment diagrams for beans shown in figure.

Q: Bar AB rotates as shown with an angular velocity equal to 10 rad/s. Assume AB ha a length of 500mm…

Q: Q is the midpoint of the line segment PR in the truss rafter shown in the figure. What are the…

Q: 1m 10 kN 5 kN/m 2m 2m- 4m A beam with a hinge is loaded as above. Draw the shear force and bending…

Q: Three pipes steadily deliver water at 20°C to a large exit pipe in Fig. P3.8. The velocity V2=5 m/s,…

Q: A 480-mm-diameter, non-slender, spiral column is symmetrically reinforced with 6-16 mm vertical…

Q: Water flows through an orifice at the vertical side of a closed cylindrical tank. The water level…

Q: Water flows in the bend shown in figure at a rate of 5 m3/s, and the pressure at the inlet is 650…

A: To solve this problem, we will use Bernoulli equation. Therefore, we will calculate all the terms…

Q: 700 kPa 4 MPa 40 MPa 600 kPa (a) (b) (c)

Q: A soil sample has a water content of 10% and a void ratio of 0.5. If the specific gravity of the…

A: Given data : Specific gravity of soil sample G=2.70 Water content of soil w=10100=0.1 Void ratio…

Q: A 440-mm-diameter, non-slender, spiral column is symmetrically reinforced with 10-20 mm vertical…

Q: 9 A simply supported beam 300 mm wide, 500 mm deep and spans 5.6 m supports a service super…

Q: Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain…

A: fy = 415MPa fc = 28MPa D = 450mm d = 450-64 = 386mm (effective depth) b =300mm d' = 70mm

Question

The diameter of a tall stand pipe with an
open top is 1.8 m, and the wall thickness is
15 mm.
1. At what water level will the stand pipe's
wall experience a 10 MPa circumferential
stress?
2. How much axial stress is there in the tank's
wall owing to water pressure?
3. If the tank is exposed to a 600 kN lateral
force at the top. Determine the tank's
shearing stress.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An open top standpipe as shown has d = 2.5 m and 30 mm wall thickness. Determine the height ? (?? ??????) of the water that will result to a circumferential stress of 10 MPa in the wall of the standpipe. NOTE: The specific weight of water ?? is 9.81 3. Remember, pressure is equals to the product of m specific weight and height. Use 2 decimal places
A masonry dam has a coefficient of permeability in the vertical and horizontal directions of Kz=4m/day and Kx=5m/day, respectively. The difference in the head is 18m and the distance between the base of the dam and the downstream water surface is 18m. Assume z=35m and width of dam = 40m. a. Determine the seepage flow (m3/day). b. Determine the uplift pressure (kPa) at A. c. Determine the uplift force (kN) acting in the dam. Assume that the uplift pressure under the dam varies uniformly.
An open top standpipe as shown has a radius r= 2.2m and 20 mm wall thickness. Determine the height ? (?? ??????)of the water that will result to a circumferential stress of 24MPa in the wall of the standpipe. NOTE: The specific weightof water is 9.81???3. Remember, pressure is equals to the product of specific weight and height. Use 2 decimal places.
A retaining wall 4m high supports a horizontal granular back-fill. The unit weight of back fil is 1.65 kN/m^3. Angle of friction of soil is 35 degrees , wall friction angle is 10 degrees. Compute the Coulumbs passive pressure coefficient . Compute the passive force per unit length of wall. Compute the location of the passive force from the bottom of wall.
For a cutoff wall shown in Figure 4a. Establish the flow nets (i.e. flow and equipotential lines) following all the rules (Drawdirectly on Figure 4).b. Deten:nine the quantity of seepage (m3/s perm) (coefficient of permeability, k = 2.0 x10·5 mis).c. Calculate the effective stress at point A (back of the piling) (Yu.t = 20 kNlm\d. Estimate the stability of the cutoff wall using lhe Factor of Safety, FS.
If the tubular shaft has an allowable shear stress of 65MPa, determine the required wall thickness of the shaft. The outer diameter of the shaft is150mm.
A 60 cm CI main pipe leads from a reservoir whose water surface is at Elev. 1590 m. Below the ground surface level, the main pipe is horizontally positioned at Elev. 1410 m. Assuming static condition, what is the stress in the pipewall if the wall thickness is 12.50 mm and the soil pressure is 520 kPa? a.18.2 MPa b.32.6 MPa c.20.5 MPa d.28.7 MPa
This is an open cylindrical vessel*It is filled 2/3. diameter = 0.60 mheight = 0.90 m90 rpma. What is the water depth at the center of the vessel?b. What is the total force exerted on the wall?c. What is the total force at the bottom?
6.3 Determine the wall shearing stress in a pipe of diameter 100mm, which conveys water. The velocities at the half the diameter from boundary is 2 m/s. The local velocity at 20mm from the pipe wall is 1.5m/s and the flow is turbulent,
Q.2 The thin-walled section is shown in figure has uniform wall thickness of 0.5 in. Assume a = 1 in, b = 3 in, h = 8 in. if it is subjected to vertical downward shear force, V = 1200 lb. a) Draw the shear flow diagram for the cross section. b) Compute the distance e from the center line of the wall to the shear center S.
A masonry dam has a coefficient of permeability in the vertical and horizontal directions of kz=4m/day and kx=5m/day, respectively. The difference in the head is 18 m and the distance between the base of the dam and the downstream water surface is 18m. Assume z=35 m and width of Dam =40m Determine a) the seepage flow b) the uplift pressure (kpa)at point A C) the uplift force (Kn) acting in the dam. assume that the uplift pressure under the dam varies uniformly
The velocity distribution near the solid wall at a section in a laminar flow is given by u = 5.0 Sin (5πy) for y ≤0.10 m. Compute the shear stress at y=0, (ii) y=0.06 m and (iii) y=0.12 m.. The dynamic viscosity of the fluid is 5 poise.