1 The cantilever beam BC is attached to the steel cable AB as shown. Knowing that the cable is initially taut, determine the tension in the cable caused by the distributed Íoad shown. Use E = 200 GPa. A CA = 255 mm² 3 m 20 kN/m В C W410 × 46.1 -6 m Fig. P15.61

1 The cantilever beam BC is attached to the steel cable AB as shown. Knowing that the cable is initially taut, determine the tension in the cable caused by the distributed Íoad shown. Use E = 200 GPa. A CA = 255 mm² 3 m 20 kN/m В C W410 × 46.1 -6 m Fig. P15.61

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.41P: The 24-ft timber ï¬‚oor joist is designed to carry a uniformly distributed load. Because only 16-ft...

See similar textbooks

Related questions

Q: ar is used to remove a nail as shown. Deter and the small support block. The moment 265 N

Q: Explain and differentiate the concept and processes of Carnot cycle, Otto Cycle/Gasoline engine, Die...

A: 1 2

Q: Reqd: Determine e of A relative to D Gst = 12 x 106 psi MN ]b• ft 2-in. diameter 1000 lb · ft 900 lb...

Q: Question 46 of 46 The mechanism shown is used to lower handicapped persons into a whirlpool tub for ...

Q: 2. Indicate the subscripts of stress components in the following cases. Use the given coordinate sys...

Q: Find COP ?

A: Given: Condenser of refrigeration system rejects heat at a rate of 190 kWCompressor consumes power o...

Q: Explain and Plot why the Head(H) arrive in meter(m) unit

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500-lb load....

Q: weight % of C in

A: Given data; Atomic weight of Fe = 65And that of carbon C=14For the data given, Find the weight perce...

Q: •3-25. Determine the maximum weight of the bucket that the wire system can support so that no single...

Q: "he and hi are KJ/kg " m (h2 - hi) mgh 2505 - 2500 = 0.00981 (h) 509.68 m v? 2(9.81) V = 10 exis

Q: PROBLEM 2: A support block is acted upon by two forces as shown. Knowing that the coefficients of fr...

A: To find Pmax the calculations are made by considering P as the force for impending motion of the blo...

Q: A rankine cycle has the specific conditions: Inlet of turbine: T= 368 degree celcius p= 11.17 mPa co...

A: Given data, Temperature at turbine inlet, T1 = 368 °C Pressure at turbine inlet, P1 = 11.17 MPa Pres...

Q: 3. A disc has a speed of 1300 rpm and it is made to slow down at a uniform rate of 3 rad/s.Calculate...

A: Rotational speed also known as the speed of revolution or rate of rotation, of an object rotating ar...

Q: A vessel contains at 1 bar and 20°C a mixture of 1 mole of CO; and 4 moles of air. Calculate for the...

Q: A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 lb/cu ft...

A: Answer: (a) The work done on the air is 2384.40 Btu/min. (b) The work done on the air is 56.24 hp. ...

Q: performance of the system ?

A: Given: Rejection of heat rate of a refrigeration system through a condenser is;Q=160 KWPower consump...

Q: Question 39 of 46 The force of magnitude Facts along the edge of the triangular plate. Determine the...

A: Rotational effect causes by force about point is called moment.

Q: In the assembly shown below, the links BD is made of brass (E = 105 GPa) with cross- sectional area ...

Q: 10 ft B 10 ft 10 ft 10 ft 4k 4k

Q: A 200-lb man starts at end A of the wooden plank and walks toward end B. If the plank will fail when...

A: Given Data: Mass of the man, W=200 lb

Q: 5.For the process flow below in the yellow highlighted boxes: (i) Mark off location of mask and resi...

A: The above process is called photolithography. It is used in integrated circuit manufacturing. It use...

Q: PROBLEM 3: Determine the tension in each of the three ropes supporting the crate. 2 ft 4 ft 4 ft B y...

Q: A car accelerates uniformly from rest and reaches a speed of 28.0 m/s in 8.00 s. If the radius of a ...

Q: Calculate the enthalpy, volume and entropy of 2 kg of steam at a pressure of 1.9 MPa having the dryn...

Q: (a) Determine the location and magnitude of the maximum abso- lute deflection in AB between A and th...

Q: A hollow, pressurized sphere having a radiusr = 4.8 in. and wall thickness t = 0.4 in. is loweredint...

Q: One of your employees is complaining of knee pain on the R. While assessing his workstation, you not...

A: Given Length of the limb, L = 38 cm Angle = 45 degree Find Distance travelled, x

Q: Determine mass of air ?

A: Given data: Volume,v=2.85 m3Temperature,T=303 kGauge pressure, pgauge=0.5 barGas constant, R=287 J...

Q: Ip 2r

A: The given two degree system can be analysed by seperating both masses and then balancing of the all ...

Q: A stone weighs 468 N in air. When submerged in water its weight reduces to 298 N. Determine the volu...

A: Weight in air=468N Weight in water= 298N Losses in weight due to bouyancy force,Force of Bouyancy =4...

Q: Given the Cu-Zn phase diagram below, determine the amount of the phase/s present of a 75 wt% Zn -25 ...

Q: QUESTION I Consider Port Phyllis wind site, assume you are installing a G80-2000 Wind turbine (k=2.6...

A: Wind power or wind energy is for the most part the utilization of wind turbines to create power. By ...

Q: temperature of 21 degrees Celsius, wet bulb temperature of 14 degrees Celsius and the second at dry ...

Q: A lawn sprinkler (shown below from above) sprays water with an exit velocity of 2.7 m/s at än angle ...

A: according to the given details

Q: A particular body weighs 60 lb on earth. Calculate its weight on the moon, where g = 5.4 ft/sec^2

A: Given Weight on earth, W = 60 lb Gravity on moon, G = 5.4 ft/sec2 Find Weight on the moon

Q: A gas initially at 15 Psia, 2ft3 undergoes a process to 90 Psia, 0.6ft3. During which the enthalpy i...

Q: The system shown in Figure 4 consists of a point mass M 5 kg and a massless L-shaped lever. The leve...

A: Given : To find : Magnitude y0

Q: diameter, and the distance from the center of the rudder stock to centerline of rams is 800 mm. Calc...

Q: teps of how to draw the BUSHING of an IV cannula using SOLIDWORKS

A: A bush, sometimes known as a shrub, is a common plant in both the garden and the wild. Many types...

Q: The two shafts are made of A-36 steel (shear modulus G = 75 MPa). Each has a diameter of 25 mm, and...

A: Given data, Shear modulus of shaft material, G = 75 MPa Diameter of shaft d = 25 mm Support A, B and...

Q: A motor is operating a load that requires a torque of 750 pounds per inch and is turning at a speed ...

A: Given data Torque = 750 pounds per inch = 62.5 lb.ft Speed 1575 rpm

Q: PROBLEM 3: Determine the tension in each of the three ropes supporting the crate.

Q: *6-12. Determine the force in each member of the truss and state if the members are in tension or co...

Q: 1 kg of air at 1 bar and 27°C is held in a cylinder of 0.8 m° capacity. The gas is heated until the ...

A: Here, Initially air is at T1=27°C=27+273=300 K; p1=1 bar V1=0.8 m3; R=287 Nm/kg K Final temperatu...

Q: PROBLEM 1: Determine the mass of the heaviest uniform bar that can be supported in the position show...

Q: A 400 W cylindrical resistance heater is 1 m long and 50 mm in diameter. The resistance wire is plac...

Q: Figure shows a friction brake in which the curved lever BC is pivoted at the fixed-point and carries...

Q: Consider the pendulum shown in the figure. Calculate: y r" А A' 0.5h" B B' h" t" C C' COLLAPSE IMAGE...

Q: Two boilers one with superheater and another without superheater are delivering equal quantities of ...

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

15.61 The cantilever beam BC is attached to the steel cable AB as shown.
Knowing that the cable is initially taut, determine the tension in the
cable caused by the distributed Íoad shown. Use E = 200 GPa.
-A = 255 mm2
3 m
20 kN/m
В
C
W410 X 46.1
6 m
Fig. P15.61
H

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A large number of uniform and identical cantilever beams, each 1 m long and 146 N / m in weight, are used to support pipes. Consider that the length of the tubes acting under a typical ABCD beam is 1.2 m. And that tubes B and C, plus their contents, weigh 365 N / m and 510 N / m, respectively, determine the reactions at the end set in A, of the cantilever beams.
A cable AB of span L and a simple beam A'B' of the same span are subjected to identical vertical loadings as shown. Show that the magnitude of the bending moment at a point C' in the beam is equal to the product T0h, where T0 is the magnitude of the horizontal component of the tension force in the cable and h is the vertical distance between point C and the chord joining the points of support A and B.
Solve Prob. 7.89 assuming that the bending moment was found to be +650 N.m at D and +1450 N.m at E.(Reference to Problem 7.89):The beam AB is subjected to the uniformly distributed load shown and to two unknown forces P and Q . Knowing that it has been experimentally determined that the bending moment is +800 N.m at D and +1300 at E, (a) determine P and Q,(b) draw the shear and bending-moment diagrams for the beam.
For the beam and loading shown, determine the magnitude of the vertical reaction at B (Ib) provided that a=156, b=126 and c=8.2 Round off only on the final answer expressed in 3 decimal places.
Determine the shape of a fully stressed, simply supported beam that supportsa concentrated force at its center, Fig. 11–11a. The beam has a rectangularcross section of constant width b, and the allowable stress is sallow.
For the loading shown, and knowing that beams AB and DE have the same flexural rigidity, determine the reaction (a) at B, (b) at E
For the cantilever beam and loading shown, determine (a) the equation of the elastic curve for portion AB of the beam, (b) the deflection at B, (c) the slope at B.
CASTIGLIANO’s THEOREM.For the rigid frame shown, determine the horizontal displacement of joint E. EI is constant.
For the beam and loading shown, determine the vertical reaction at A (lb) provided that a=190, b=104, c=10 and d=5. Round off only on the final answer expressed in 3 decimal places.
Knowing that the average normal stress in member EF of the Pratt bridge truss shown must not exceed 8.36 ksi for the given loading, determine the cross-sectional area (in sq. in) of this member that will yield the most economical and safe design if h = 14.2 ft and P = 87.28 kips.
The cantilever beam BC is attached to the steel cable AB as shown. Knowing that the cable is initially taut, determine the tension in the cable caused by the distributed load shown. Use E = 200 GPa.
The 24-ft timber ï¬‚oor joist is designed to carry a uniformly distributed load. Because only 16-ft timbers are available, the joist is to be fabricated from two pieces connected by a nailed joint D. Determine the distance b for the most advantageous position of the joint D, knowing that nailed joints are strong in shear but weak in bending.