1) The color of this resistor 47 k52 A yellow, violet,orange. b) yellow, violet, red c) yellow,blue, red d) yellow, green, orange When an ohmmeter is used to test a diode, a very low resistance (but not zero) in both direction means that the diode is -(a) Open (b) Shorted (c) Forward bias (d) Reverse biased tantial

1) The color of this resistor 47 k52 A yellow, violet,orange. b) yellow, violet, red c) yellow,blue, red d) yellow, green, orange When an ohmmeter is used to test a diode, a very low resistance (but not zero) in both direction means that the diode is -(a) Open (b) Shorted (c) Forward bias (d) Reverse biased tantial

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80 amp-hours each to provide battery backup for their computers. The lead-acid cells are to be replaced with nickel-metal hydride cells with a capacity of 40 amp-hours each. How many nickel-metal hydride cells will be required to replace the lead-acid cells and how should they be connected?
Consider the diode circuit below, with both diodes having 0.7 V across them when they conduct. V(1) = 10sinwt V (AC)V(2) = 4 V (DC)R(1) = R (2) = 1.3 k(ohm) Over a full cycle of the AC input: 1. Calculate the maximum current through diode 1 (D1). Explain and show all steps. 2. Find the voltage across each resistor. Explain and show all steps. 3. Sketch the current waveform across diode 2 (D2). Label all important points. Explain and show all steps.
In your own tought please help me understand by explaining the following : 1.How will you determine the anode and the cathode terminals of a diode if there are no markings on the diode? 2.What conditions identify a defective diode? 3.Is it possible for the current to flow in a diode when reverse-biased? Explain. 4. What is the connection between forward and reverse biase? Thanks!
In this Zener diode regulator, the source voltage varies from 6 V to 11 V. Assume that the load current varies between 2 mA and 48 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures. Please answer in typing format solution please only typing format solution please
(1-a) Explain the operation of the Zener diode in forward and in reverse bias. (1-b) Analyze the circuit thoroughly assuming many source values that lead to all possible cases of diode states. For each case (Hint: 3 cases), re-plot the circuit and develop the relation between the output voltage and the source. (1-c) Draw input and output waveforms accurately over 0.5-ms period. Identify the diode states on the graph based on the categorization of cases from part (1-b).
a. Determine VL, IL, and IR for the network of below if RL=180 ohms b. Repeat part (a) if RL=470 ohms c. Determine the value of RL that will establish maximum power condition for the Zener diode. d. Determine the minimum value of RL to ensure that the Zener diode is the the "on" state.
The diodes in the circuit are all Silicon with forward voltage of 0.7 V. If R1 = 9 Ω and R2 = 13 Ω, determine the value of the current I in amperes. Your answer should be accurate to two decimal places.
3.The diodes in the following circuit have piecewise linear parameters VT=0.7V and rf=0. Determine the output voltage V0 and the diode currents ID1 and ID2 for the following input conditions: (a)V1=10V, V2=0; (b)V1=5V, V2=0; (c)V1=10V, V2=5; and (d) V1= V2=10V. Please answer in typing format please ASAP