Q1:- complete the following sentences (answer 10 only)1- The maximum conversion efficiency in class-B push pull P.A. is...2- Voltage shunt negative feed-back stabilize.....3- Precision diode using op-amp is used to...... very small voltages.4- The ratio of differential mode gain to common mode gain of op-amp is called ...5- In sample and hold circuit the op-amp is used as....6- The bandwidth of ideal op-amp is.....and the output resistance is...7- The transistor employed in multi-vibrator is used as ....8- The 555 timer can be wired to operate as .... or .... Multivibrators.9- Oscillation occurs when the loop gain of oscillator circuit has a magnitude of... and loop phase shift of....10- The R-2R D/A converter has resistance spread of.....11-The ideal op-amp voltage follower has a gain of ...Crystal oscillator is used to provide stable.....12-13-Impedance matching in tuned amplifier is used to improve....

The function of the electronic circuit function and application needs to be discussed and the…

1- The maximum conversion efficiency in class-B push pull P.A. is... 2- Voltage shunt negative feed-back stabilize ..... 3- Precision diode using op-amp is used to...... very small voltages. 4- The ratio of differential mode gain to common mode gain of op-amp is called ... 5- In sample and hold circuit the op-amp is used as.... 6- The bandwidth of ideal op-amp is .....and the output resistance is...

1- The maximum conversion efficiency in class-B push pull P.A. is... 2- Voltage shunt negative feed-back stabilize ..... 3- Precision diode using op-amp is used to...... very small voltages. 4- The ratio of differential mode gain to common mode gain of op-amp is called ... 5- In sample and hold circuit the op-amp is used as.... 6- The bandwidth of ideal op-amp is .....and the output resistance is...

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Sketch the voltage transfer characteristics of an ideal voltage amplifier and a real voltageamplifier. Ensure to label the important regions.
2. Select ONE (1) transducer or sensor with available in the market, with providing the brand, model and technical specification of the selected transducer or sensor, you are required to i. Explain its designed measurand and the working range. ii. Explain its basic working principles and any steps required to take in order to avoid any error (ex. Loading error) during measurement process. iii. Identify either the selected transducer or sensor required a signal conditioner. iv. Propose ONE (1) cable with is suitable to be connected with the selected transducer or sensor
Give an overview and insights when design and creating an AC-DC power supply with selectable output voltage which employs a full bridge rectifier, filter capacitors, and regulator. What are the objectives
Consider the operational rectifier or superdiode circuit, with R=1kohm. For v1=10mV, 1V, and -1V, what are the voltages that result at the rectifier output and at the output of the op amp? Assume that the op amp is non-ideal and that its output saturates at ± 12V. The diode has a 0.7-V drop at 1-mA current.
Please show calculations of operating currents and voltages. Values are located in table. Please verify that op-amp, BJT and Diode are within its operating limits.
Create an objectives when design and creating an AC-DC power supply with selectable output voltage which employs a full bridge rectifier, filter capacitors, and regulators. Create also a schematic diagram.
For the 2 circuits shown above, βnpn = 100, βpnp = 50, VDO = 0.7 V, R2 = 150 kΩ, and RB = 12 kΩ Using the ac small-scale signal analysis, determine for each circuit: a) The voltage gain (Av = vout/vin) b) The input resistance (Rin) c) The output resistance (Rout)
What is the output voltage vO if theop-amp is ideal? What are the values of the baseand emitter currents and the total current suppliedby the 15-V source? Assume βF = 60. What is theop-amp output voltage?
The circuit diagram of step-up type DC-DC converter is given below. It is assumed that the output capacitor is large enough and the output voltage is constant. (Consider that there is no circuit losses.) What should the inductance value be for the circuit to always operate in Continuous Current Mode (CCM)? Calculate.
Provide a detailed explanation on differential amplifier circuits explain how these circuits work. explain input biasing ,offset current, output offset voltage, common-mode gains,and common-mode rejection-ratio (CMRR). also list possible sources of error that can occur when conducting a differential amplifier circuit experiment.
A ) The dual slope method, it’s the popular method for converting an analog voltage into a digital value.Explaine that in details.
Suppose a power supply is energized by an AC source of 119 V RMS. The transformer step-down ratio is 8:1, it uses a full-wave bridge rectifier circuit with silicon diodes, and the filter is nothing but a single electrolytic capacitor. Calculate the unloaded DC output voltage for this supply (assume 0.7 volts drop across each diode). Also, write an equation solving for DC output voltage (Vout), given all these parameters.