1) Transmission line properties of typical high-speed interconnects are experimentally investigated by fabricating and characterizing coplanar strip interconnects on semi-insulating GaAs substrates. The values of the attenuation constant a, phase constant B, and characteristic impedance z, at 20 GHz are determined. From the measurements, a = 1.4 Np/cm, ß = 2 rad/cm and Z, = 112 - j300. If the length of the coplanar strip transmission line is 30 m, calculate Resistance R (1) (ii) Inductance L Conductance G (iv) Capacitance C

1) Transmission line properties of typical high-speed interconnects are experimentally investigated by fabricating and characterizing coplanar strip interconnects on semi-insulating GaAs substrates. The values of the attenuation constant a, phase constant B, and characteristic impedance z, at 20 GHz are determined. From the measurements, a = 1.4 Np/cm, ß = 2 rad/cm and Z, = 112 - j300. If the length of the coplanar strip transmission line is 30 m, calculate Resistance R (1) (ii) Inductance L Conductance G (iv) Capacitance C

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A microwave link includes two sites that are 10 km apart and uses a center frequency of 9 GHz. On either transmitter or receiver side, a 100-m transmission line that has an attenuation per unit length of 0.01 dB/m is connected to an amplifier and a parabolic reflector antenna. Other losses caused by connectors and insertions incurred on one side amounts to 3 dB. Antenna has a power gain of 20 dB. If the output of the transmitter amplifier is 30 dBm, what is the received signal level (in dBm) at the input of the receiver amplifier?
Calculate the guided intrinsic impedance at 20 GHz for the lowest-order mode of therectangular waveguide with dimensions a=0.7 in and b=0.3 in.Take relative permittivity as 2.76.
In microwave communications systems, for a carrier frequency of 6GHz and a distance of 40 km. determine the free space path loss in dB.
2. A system is being designed to use a 30 GHZ link with a 300HZ bandwidth to receive signals from a navigation spacecraft at an altitude of 20,200km, with a maximum slant range of 24,700km. The satellite transmitter-antenna gain is 25db and the handheld unit receiver gain is 5db. The transmitter power will be 18W. If the handheld receiver temperature is 500K, will this be an effective link (S/N at least 10 or 10db)? If not, what could you change to improve the link?
A cellular service provider decides to use a digital TDMA scheme which can tolerate a signal- to-interference ratio of 15 dB in the worst case. Find the optimal value of N for(a) omnidirectional antennas, (b) 120° sectoring, and (c) 60° sectoring. Should sectoring beused? If so, which case (60° or 120°) should be used? (Assume a path loss exponent of n=4and consider trunking efficiency.)
Question)The coupling factor and isolation of a lossless, symmetric directional coupler are 8 dB and 20 dB respectively. Determine the scattering matrix of the directional coupler. Also determine the directivity of the device? This Question from Microwave systems course.
How does the choice of transmission medium impact network latency and bandwidth, and what factors should be considered when selecting the appropriate medium for a specific application?
1.) A communication system is defined below:Transmitter Power: = 45 dBm; Frequency = 1 GHzTransmit Antenna: Gain = 12 dB, height above ground = 50 meters;Receive Antenna: Gain = 6 dB, height above ground= 2.5 metersFind the received power (in dBm) at a range of 4 kilometers:a. using the free-space range equation b. using the near-earth range equation Using the results of the calculations in a & b above: c. determine the best prediction of the received power (in dBm) at the 4 kilometer range. 2.) A transmitter operating at 80 MHz has an output power of 1.5 kW which is fed to an antenna with a gain of 20 dB. Determine the "keep-out" distance (in meters) required to meet the safety standard. clear and easy to understand. Thanks
Since S = 1.7 in a transmission line to be used at 2 GHz; What is the length, in cm, of the parallel lateral line required to match the transmission line to the load impedance?
1.) A communication system is defined below:Transmitter Power: = 45 dBm; Frequency = 1 GHzTransmit Antenna: Gain = 12 dB, height above ground = 50 meters;Receive Antenna: Gain = 6 dB, height above ground= 2.5 metersFind the received power (in dBm) at a range of 4 kilometers:a. using the free-space range equation b. using the near-earth range equation Using the results of the calculations in a & b above: c. determine the best prediction of the received power (in dBm) at the 4 kilometer range. answer should be a) -41.15 b) -39.1 c.) near FS
A wireless communication system has a trasmit power Pt = 10 mW. Through extensive measurements, the path gain of the system at the reference distance is determined to be -32 dB, and the path loss exponent to be 3.8. Using the simplified path loss model, find the received power in mW at distance 200 meters from the transmitter
A lossless coaxial cable with L = 0.5 uH/ft and C = 100 pF/ft is terminated by a 100-ohm resistive load. What is the characteristic impedance of the quarter-wavelength line that can be used for impedance matching?