1Which one of the following statement is "false" regarding the Intelligent power modules(IPMs)?(i) IPMs normally include gate-drive circuits to drive individual devices or modules.(ii) A micro-controller or micro-computer is an essential part of an IPM.(iii) IPMs do not necessarily need smart power technology where the load currentshould be continuously monitored.(iv) An IPM noramlly integrate the power modules with a protection and diagnosticcircuit (against excess current, short circuit, an open load, overheating, and anexcess voltage).2 A diode (PN junction) employs the following doping levels: N₁ = 10¹6 cm-³ andNAN₂ = 5x105 cm-³. If we calculate the hole and electron concentrations on two sides,which one of the following statements is true?(i) Concentration on p side is pp = 10¹6 cm-³ and n = 1.1x104 cm-³. Concentrationon n side is n₁ = 5 x 10¹5 cm-³ and pn = 2.3x104 cm-³.(ii) Concentration on p side is pp = 104 cm-³ and np = 1.1x104 cm-³. Concentrationon n side is n₁ = 5 x 104 cm-³ and pn = 2.3x104 cm-³.(iii) Concentration on p side is pp = 10¹6 cm-³ and n = 2.3x104 cm-³. Concentrationon n side is n = 5 x 10¹5 cm-³ and pn = 1.1x104 cm(iv) Considering the given information, the concentrations on both side cannot be cal-culated. However, we can deduce that the majority carrier concentration on eachside is many orders of magnitude higher than the minority carrier concentrationon either side.

Note: We are authorized to answer only one question at a time. Kindly repost the other question in…

1 Which one of the following statement is "false" regarding the Intelligent power modules (IPMS)? (i) IPMs normally include gate-drive circuits to drive individual devices or modules. (ii) A micro-controller or micro-computer is an essential part of an IPM. (iii) IPMs do not necessarily need smart power technology where the load current should be continuously monitored. (iv) An IPM noramlly integrate the power modules with a protection and diagnostic circuit (against excess current, short circuit, an open load, overheating, and an excess voltage).

1 Which one of the following statement is "false" regarding the Intelligent power modules (IPMS)? (i) IPMs normally include gate-drive circuits to drive individual devices or modules. (ii) A micro-controller or micro-computer is an essential part of an IPM. (iii) IPMs do not necessarily need smart power technology where the load current should be continuously monitored. (iv) An IPM noramlly integrate the power modules with a protection and diagnostic circuit (against excess current, short circuit, an open load, overheating, and an excess voltage).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design an interfacing system for solar controller, your design should monitor the solar system data like solar panels output, energy consumption, battery charging current, etc, the system must have keypad input and LCD display to allow users to view system status and adjust system parameters like max charging current, max consumption load. ...Draw a detailed block diagram of the interfacing system showing all the signals
MECT361 Mechatronics Components and Instrumentation PLEASE GIVE ME THE REFRENCE (((please note that it is not allowed to copy paste from any reference unless you mention the reference appropriately at the end of your report. Besides, you must put the copy-pasted part of your report in quotations (i.e. " ").)))
Given the overall reliability of the LCD display unit consisting of a display, a backlight panel and several circuit boards with the following setup. As an engineer, you are required to draw a diagram of the model in your answer along with a brief description of it. a) An LCD panel with hardware failure rate, ʎ1 b) A backlighting board with 10 bulbs with individual bulb failure rate of ʎ 2 but still considered good with 2 bulbs failures c) 2 microprocessor boards A and B hooked up in parallel, each with total circuit board failure rate of ʎ 3 d) Dual power supplies, C and D in a standby redundancy, with a failure rate of ʎ 4,for each power supply e) EMI board with failure rate ʎ 5 if hooked up in series with the common input of the power supply C and D.
Could you answer this question in details and giving examples if possible. Thanks a lot. - Explain what is CAN BUS. This question is related with the Embedded system ( Electrical electronic engineering)
INFE242 ELECTRONICS PLEASE i begging you help me in this problem ?? Please make it clear ALL thank and appreciation ?? ?
4. Are the following statements correct or wrong? Justify your answer. (a) GTO requires very low current applied to its gate to be turn off. (b) IGBT is a voltage driven device. (c) BJT is more efficient than IGBT in high power applications. (d) Thyristors are used only for low voltage, low current applications. (e) MOSFETs are used for high frequency applications.
Know how to design simple voltage-divider and currentdivider circuits How much power is dissipated in the 25 kΩ resistor if the load terminalsare accidentally short-circuited?
Do you know how to stop a rapid rise in power supply from destroying and malfunctioning your computer? If so, please share your thoughts in the section below.
2b) You are designing electronic circuit component for the Highway Authority to be used for vehicular traffic management at a junction because your best friend was knocked down at the junction due to lack of traffic management. What type of materials would you used?
What happens to availability as the MTTR rises, implying that repairing a device becomes more difficult? Does this mean that the device is in short supply?
It is necessary to reduce the power consumption of a system by at least 5 times using pipelining. For the threshold voltage of 0.4 V and initialsupply voltage of 5 V, at what level should the system be pipelined? What is the supply voltage of the pipelined system?
Evaluate the use of analogue and digital electronic devices, in complex systems like a scientific calculator and an amplifier. For the calculator look at the input components such as chips (IC) on a circuit board, switches what do they do. The processor (microprocessor) chip (IC), central processing unit (CPU), what does it do. The output, display screen LCD, what does it do. The power source, batteries, lithium, alkaline. Where would you expect AND, OR, NOT, EXOR gates to be used. What are FULL ADDER/HALF ADDER circuits show the circuits. How is multiplication done. For the amplifier Look at the input, a small voltage/current is applied, uses the power supply to help to increase the input signal, via a transistor/op-amp integrated circuit (IC). Uses, to drive headphones, speakers. Types of amplifiers, Audio frequency, Radio Frequency, video amplifiers etc. Classes of amplifiers such as class A, B, C and AB.