please answer problem 2 1.From the typical results of a UC test in Figure 1, determine the unconfinedcompression strength and the corresponding axial strain (Remember to include units on youranswers!):1412106.101520Vertical Strain, ɛ (%)Figure 1: Relationship between vertical stress and axial strain in a UC test2.Sketch Mohr's circle and determine the undrained shear strength, Cu. Show on yoursketch the hypothetical failure plane.004-2.Vertical Stress, o (psi)

As shown in the graph the maximum vertical stress which is also known as unconfined compressive…

1. 2. From the typical results of a UC test in Figure 1, determine the unconfined compression strength and the corresponding axial strain (Remember to include units on your answers!): Vertical Stress, o (psi) 14 12 10 8 4 2 0 0 5 10 Vertical Strain, & (%) 15 20 Figure 1: Relationship between vertical stress and axial strain in a UC test Sketch Mohr's circle and determine the undrained shear strength, Cu. Show on your sketch the hypothetical failure plane.

1. 2. From the typical results of a UC test in Figure 1, determine the unconfined compression strength and the corresponding axial strain (Remember to include units on your answers!): Vertical Stress, o (psi) 14 12 10 8 4 2 0 0 5 10 Vertical Strain, & (%) 15 20 Figure 1: Relationship between vertical stress and axial strain in a UC test Sketch Mohr's circle and determine the undrained shear strength, Cu. Show on your sketch the hypothetical failure plane.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

Q. No .3 On the free surface of an aluminum [E = 10,000 ksi; v = 0.33] component, the strain rosette shown in the figure was used to obtain the following normal strain data: = -500 µɛ, E = -220 µe, and &e = +600 µɛ. Determine the normal stress that acts along an axis that is rotated at an angle of 0= 45° coun- terclockwise from the positive x axis. 60 60 60
The stresses at a point in a bar are o1 = 28N/mm2 (tensile) and o2=12N/mm2 (compressive) as shown in Figure (a) Determine the normal, tangential and resultant stress in magnitude and direction on a plane inclined at 55° to the axis of the major stress. (b) Determine the maximum intensity of shear stress in the material at the point. (c) Also, solve the same problem using Mohr's circle method and compare the results. O2 Axis of Major Stress 55°
Point A in a beam is deformed such that the strain components are ɛx = -1380 µɛ, ɛy = -880 µɛ, Ez = 0 µɛ, and yxy = 1470 prad. Determine the magnitude of the absolute maximum shear strain at the point. Answer: Absolute maximum shear strain = i prad
The strain rosette shown in the figure was used to obtain normal strain data at a point on the free surface of a machine component. ɛa= -250 µm/m, ɛb= -35 µm/m, and ɛc= 390 µm/m.[E= 29000 ksi, G= 10900 ksi, a= 40 °] y X a Determine the maximum absolute shear stress. 8660 psi 4190 psi 9810 psi 7020 psi 15000 psi O0000
The components of plane stress at a critical point on a steel shell are shown in the figure below. The yield stress (Gy) of the material in simple tension is 250 MPa. 60 MPa 40 MPa 70 MPa (a) Determine the magnitude of the principal stresses and maximum shear stress. Sketch these on appropriately orientated elements. (b) Calculate the factor of safety against yield on the basis of i. Tresca failure criterion ii. Von Mises failure criterion
Current Attempt in Progress 60 MPa, Gy At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx = 110 MPa, and Txy = 28 MPa, acting in the directions shown in the figure. Exy Ox At this point, determine the strain components Ex, y, z, and Yxy. Assume that E = 72 GPa and v=0.31 for the machine component. με Ex = με NO || || με μrad =
PROBLEM 1 A circular aluminum tube of L=600mm is loaded in by compressive forces at its ends. The outside and inside diameters are 75mm and 63mm respectively. A strain gage is placed on the outside of the tube to measure nomal strains in the longitudinal direction. E=73 GPa and Poisson's is 0.33. a. If the normal stress in the tube is 57 MPa, what is the load P? b. if the strain is 781 X 10-6, what is the shortening of the tube? What is the percent change in its cross-sectional area.
At a point in a stressed material, the stress combination acting on a plane is a 90 kPa compressive stress and a 30 kPa shear stress, while on a perpendicular plane, the stress combination is 30 kPa compression and 30 kPa shear. Use the Mohr’s circle for this stress analysis. (a) Determine the values of the major and minor principal stresses. (b) Determine the angle between the major principal plane and the plane where the 90 kPa compressive stress acts.
The brass sculpture with a height of 10m experiences shear forces of 30,000N. The area of the face being sheared is 100m^2. With the force, the object moved 5m horizontal distance. Determine the stress and the strain: (S brass-3.5×10^10 Pa). O Stress: 3OOPA Strain: 0.5 O Stress: 100PA Strain: 0.3 O Stress: 0.5Pa Strain: 30 O Stress: 10PA Strain: 0.5
A square plate of side 300 mm is subjected to pure shear of intensity 100 MPa as shown in figure. Young's modulus of the material is 2 x 105 MPa and Poisson's ratio is 0.2. Find the algebraic sum of principal strains. 100 MPa B 100 MPa A D
A tapered cantilever beam AB having rectangular cross sections is subjected to a concentrated load P = 46 lb and a couple Mo = 790 lb - in. acting at the free end [see the figure part (a)). The width b of the beam is constant and equal to 1.0 in., but the height varies linearly from ha = 2.0 in. at the loaded end to hp = 3.0 in. at the support. Use L = 20 in. Мо В hg (a) 3P qo = T Мо (b) ЗР 90 =7 \ Mo.
4. For the strain &¸ =ɛ, = 0, Y¸ = 0.002828 (in x-y coordinate system) at a specific point in an isotropic material, using the Mohr's circle of strain to determine the strain components &, &,, and ym in n-t coordinate system shown in the following figure. tn y 22.5° n