1. A 5 kVA, 200 V / 100 V, 50HZ single phase transformer has the following parameters:HV winding Resistance = 0.0250HV winding leakage reactance = 0.25 2LV winding Resistance = 0.005 2LV winding leakage reactance = 0.05 2400 ΩMagnetizing reactance in HV side = 190 2Resistance representing core loss in HV sideVersion 2 EE IIT, KharagpurDraw the equivalent circuit referred to [i] LV side and [ii] HV side and insert all theparameter values.

Answered: Image /qna-images/answer/f54bdc56-8326-43d7-ab58-369c6d51a7fb.jpg

1. A 5 kVA, 200 V/ 100 V, 50HZ single phase transformer has the following parameters: HV winding Resistance = 0.0250 HV winding leakage reactance = 0.25 2 LV winding Resistance = 0.005 2 LV winding leakage reactance = 0.05 2 400 2 Magnetizing reactance in HV side = 190 2 Resistance representing core loss in HV side Version 2 EE IIT, Kharagpur Draw the equivalent circuit referred to [i] LV side and [ii] HV side and insert all the parameter values.

1. A 5 kVA, 200 V/ 100 V, 50HZ single phase transformer has the following parameters: HV winding Resistance = 0.0250 HV winding leakage reactance = 0.25 2 LV winding Resistance = 0.005 2 LV winding leakage reactance = 0.05 2 400 2 Magnetizing reactance in HV side = 190 2 Resistance representing core loss in HV side Version 2 EE IIT, Kharagpur Draw the equivalent circuit referred to [i] LV side and [ii] HV side and insert all the parameter values.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.16P: A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters:...

See similar textbooks

Similar questions

A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
All values of a transformer are proportional to its __________________ ___________________.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
Rework Example 3.12 for a+10 tap, providing a 10 increase for the high-voltage winding.
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
An open-delta three-phase transformer system has one transformer center-tapped to provide a neutral for single-phase voltages. If the voltage from line to center tap is 277 V, what is the high-leg voltage?
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.