1. A building exhaust fan for a large commercial bullding weighs 180 pounds and operates at a speed of 600 rpm. Due to manufacturing tolerances, it may have a rotating imbalance. It is desired to limit force transmissibility to 2.5 as the fan passes through resonance during startup and wind-down. In addition, an isolation of 90% is required at the operating speed of the fan. The fan's framework will be supported from the floor at 4 corners. Design, select, and specify vibration isolators at the four corners. It is acceptable to assume the center of gravity is symmetrical with respect to all four corners, enabling you to treat this as a single DOF system without pitch or yaw.

1. A building exhaust fan for a large commercial bullding weighs 180 pounds and operates at a speed of 600 rpm. Due to manufacturing tolerances, it may have a rotating imbalance. It is desired to limit force transmissibility to 2.5 as the fan passes through resonance during startup and wind-down. In addition, an isolation of 90% is required at the operating speed of the fan. The fan's framework will be supported from the floor at 4 corners. Design, select, and specify vibration isolators at the four corners. It is acceptable to assume the center of gravity is symmetrical with respect to all four corners, enabling you to treat this as a single DOF system without pitch or yaw.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Thomas meter is located in an air duct of 2 sq ft cross-sectional area. The air weighs 0.083 lb per cu ft, and its specific heat is 0.24. Assume a controlled temperature differential of 5° and heater potential of 110 volts. Plot the velocity as abscissa and amperage as ordinate for veloc- ity 0 to 300 ft per min. Assume constant amperage of 3, and plot tem- perature difference against velocity. Discuss the curves from the stand- point of accuracy of the system.
2.5-L bench scale bioreactor is used for the production of recombinant P64K protein from Neisseria meningitides. The dimensions for the bioreactor are Dt 12.9 cm, ratio Di/Dt = 1/3 and N = 700 rpm. With the scale up factor of 2.24, determine the impeller tip speed (m/s) for the pilot scale bioreactor based on constant impeller tip speed and constant power consumption per volume. Predict which scale up method might give a higher concentration of P64K, if the demand of dissolved oxygen plays an important role.
1. For a given pump, the diameter, the gauge pressures at the inlet and outlet are −30 × 103 P a and 200 × 103 P a, respectively. If the flow rate is 0.1 m3/s, and the power required is 25 kW, find the efficiency. The intake and discharge are at the same height. 2. The impeller of a radial-flow turbine has an outer radius of 4 f t, turning at 200 rpm. The volume flow rate is 1000 ft3/s, and it discharges in the axial direction. Neglect all losses. If the tangential component of the velocity at the inlet is 5 f t/s, find: (a) The torque exerted on the impeller. (b) The power developed by the machine.
A farmer has a pump which discharges 100 lpm of water at a head of 10 m. The pump is driven by anelectric motor at speed of 1700 rpm through 4”x 4” pulley-drive combination for the motor and thepump, respectively, what would be the pump output if the motor pulley is changed to six inchesdiameter?
3kg mass. P= 155N and w=0
A Pelton wheel is supplied with 6kg/s of water at 70m/s. The buckets rotate on a mean diameter of 350mm at 1200 rev/min. the deflection angle is 165º and friction negligible. a). Determine the diagram power.(5mks) b). Draw the vector diagram to scale and determine change in water velocity.(5mks)
A 3-bladed wind turbine with 250 kW generator has diameter of 50 m and tower height of 60 m. It is designed to have Cp of 0.25 at wind speed of 12 m/s when regulation starts. The cut-in and furling Speeds for the machine are 5 m/s and 20 m/s respectively. Mechanical and electrical efficiencies are 90 % and 95 %. By assuming the density of air as 1.225 kg/m3. Calculatea. What is power developed by the rotor at 12 m/s when regulation starts? b. If the tip-speed ratio at this wind speed is 4.2, then what is the rpm of the rotor? c. Calculate the actual torque developed. d. Calculate the maximum possible annual power output.
In the centrifugal fan impeller there is a loss by friction of 0.4 times the kinetic head corresponding to the relative outlet velocity, and in the volute there is a gain equivalent to 0.5 times the kinetic head corresponding to the absolute velocity at exit from the runner. The impeller has an inner radius of 250 mm and width of 187.5 mm; the values at exit are 375 mm and 125 mm, respectively. There is no whirl at inlet, and at outlet the blades are backward facing at 70° to the tangent. The discharge of air is 5.7 m3/s when the speed is 13.5 rps, the density of the air is sensibly constant at 1.25 kg/m3 throughout, and mechanical losses account for 220 Watts. Neglecting the thickness of the blades and whirl slip, determine the following: The head gained, in meters, across the fan. The Brake Horsepower required to drive the fan.
In the centrifugal fan impeller there is a loss by friction of 0.4 times the kinetic head corresponding to the relative outlet velocity, and in the volute there is a gain equivalent to 0.5 times the kinetic head corresponding to the absolute velocity at exit from the runner. The impeller has an inner radius of 250 mm and width of 187.5 mm; the values at exit are 375 mm and 125 mm, respectively. There is no whirl at inlet, and at outlet the blades are backward facing at 70° to the tangent. The discharge of air is 5.7 m3/s when the speed is 13.5 rps, the density of the air is sensibly constant at 1.25 kg/m3 throughout, and mechanical losses account for 220 Watts. Neglecting the thickness of the blades and whirl slip, determine the following:The head gained, in meters, across the fan. The Brake Horsepower required to drive the fan.
Question1B Finally, design a simple mass-spring-damper, indicate the values of the system, and provide an equation where the system is in a resonant state.
A spring-loaded gun has a spring for which mNk/180=and is initially compressed bycm14. It fires a kg024.0projectile vertically. Find the maximum height above the initial position
Write and compare the equation of mechanical and electrical SHO? And a mass stand in floor which execute SHM vertically at 5hz frequency .show that mass losses contact with floor if displacement exceed 1 cm.?