1. A channel of width 450 mm branches into two sub-channels having width 300 mm and 200 mm as shown in figure. If the volumetric flow rate (taking unit depth) of an incompressible flow through the main channel is 0.9 m3/s and the velocity in the sub-channel of width 200 mm is 3 m/s, the velocity in the sub-channel of width 300 mm is m/s. Assume both inlet and outlet to be at the same elevation. Width = 300 mm Width = 450 mm Flow rate = 0.9m³/s Width = 200 mm Velocity = 3 m/s

1. A channel of width 450 mm branches into two sub-channels having width 300 mm and 200 mm as shown in figure. If the volumetric flow rate (taking unit depth) of an incompressible flow through the main channel is 0.9 m3/s and the velocity in the sub-channel of width 200 mm is 3 m/s, the velocity in the sub-channel of width 300 mm is m/s. Assume both inlet and outlet to be at the same elevation. Width = 300 mm Width = 450 mm Flow rate = 0.9m³/s Width = 200 mm Velocity = 3 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A channel step, shown in the figure below, is in a 12 m wide channel with discharge, Q, of 46 m3/s. The flow depth at section 1 is 1.6 m and the step height is 0.4 m. The bed of the channel, upstream and downstream of the step, is horizontal and smooth. Part A. Sketch on the figure the variation of the pressure with depth at sections 1 and 2, and on the verticalface of the step. Sections 1 and 2 are located far enough from the step for the velocity to be essentially horizontal and uniform. Part B. Draw the control volume contained between sections 1 and 2 and show on the figure the forces acting on it. Show also your choice for the positive direction of distance and of force. Part C. Write the momentum equation as applied to the control volume between sections 1 and 2, using the sign convention you have chosen. Show the forces and velocities used in the momentum equation. Part D. Compute the following quantities: (a) Velocity of flow at section 1. (b) Specific energy at section 1. (c)…
The unit flow rate passing through a wide channel is 6.0 m2/s. As shown in the figure, the channel consists of three infinitely long sections with different slopes, and the base slopes of each section are shown on the figure. There is a fully closed vertically movable cover in the S01 inclined channel and the water passes over the cover. The water depth formed just downstream of the cover is 0.6m, and the height of the relief structure at the beginning of the S03 inclined channel is 4m. What is the water depth at the end of the profile formed just upstream of the vertically moving cover in the S01 inclined channel by taking the Manning coefficient of friction of 0.02?
A submerged sharp crested weir 0.81 m high stands clear across a channel having vertical sides and width of 3.15 m. The depth of water in the channel of approach is 1.26 m, and 10.5 m downstream from the weir the depth of water is 0.93 m. Determine the discharge in litres per minute. Assume Cd1 = 0.58 and Cd2 = 0.80.
1. A diverging pipe has diameter of 20cm and 30cm respectively at section 1 and section 2. If the velocity of water at section-1 is 5 m/s, determine the discharge through this pipe. Determine the velocity at section-2. 2. A 50cm diameter pipe, conveying water, branches into two pipes of diameter 30cm and 20 cm respectively. If the average velocity in the 50 cm diameter pipe is 2.5 m/s, find the discharge in this pipe. Also determine the velocity in 20 cm pipe if the average velocity in 30 cm diameter pipe is 1.5 m/s.
The penstock of hydroelectric turbine is 0.5m x 0.5m with velocity of 5.5m/s and head of 20m. What is the output of the turbine if the turbine efficiency is 92%?
The flow rate passing through a rectangular channel with a base width of 4 meters and a water depth of 2.75 meters is 30 m3/s. This channel is narrowed as shown in the figure. If two (2) sections have a base width of 2m, what is the water depth in section (1) in meters (m)?
What is the gross head (m) of a small hydroelectric dam that can produce 10 kW ofpower if the penstock discharge is 1,500 li/min?
Water áows in a rectangular channel of width, w. In some cases, the water may suddenly increase in elevation as shown in the figure (from h1 to h2) through a highly disturbed region called a hydraulic jump. Assume the velocity is uniform at stations 1 and 2, and assume the pressures are distributed hydrostatically. Using the Bernoulli equation and whatever other necessary equation(s), finnd the equation (cubic) for the downstream depth, h2, in terms of h1, V1, and g.
find Step 1: Known, UnknownStep 2: SchematicStep 3: FormulaStep 4: CalculationsStep 5: Discussion A 30 cm diameter pipe, conveying water, branches into two pipes of diameters20 cm and 15 cmrespectively. If the average velocity in the 30 cm diameter pipe is 2.5 m/s, find the discharge inthis pipe (m3/s). Also determine the velocity (m/s) in 15 cm pipe if the average velocity in 20cm diameter pipe is 2 m/s.
A project engineer notices the site of a former sawmill along a river. Ruins of the original dam used as a hydropower source is still visible. The engineer decides to make some measurements to determine the maximum power that can be generated if the site were rehabilitated, the stream flow is found to be 25m3/s and the change in elevation is 4.87m. Determine the maximum power that could be produced
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4.5 times the velocity head in the siphon. Determine the flow rate in the siphon in lit/sec Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: li/s Decimal Places required in the final answer: 3
A 150 mm diameter pipe carries 81.3 L/s of water. The pipe branches in to two pipes one is 50 mm in diameter and the other is 75 mm. What is the velocity in 75 mm pipe if the velocity of the flow in 50 mm pipe is 10 m/s? a. 13.96 m/s b. 15.67 m/s c. 17.25 m/s d. 19.43 m/s