Answered: 1. A metal rod 20 mm diameter and 2 m…

1. A metal rod 20 mm diameter and 2 m tong is subjected to a tensile force of 60 kN, it showed and elongation of 2 mm and reduction of diameter by 0.006 mm.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Related questions

Q: Two solid cylindrical rods support a load of P 22 kN, as shown. Rod (1) has a diameter of 12 mm and…

A: Given, two solid cylindrical rods. Load P =22 KN Diameter of rod 1 =12mm Diameter of rod 2 =16 mm…

Q: Determine the total deformation in inches if the flexural rigidity is equivalent to 5,000 kips. 6…

Q: Review The beam is made from a plate that has a constant thickness b. (Figure 1) Part A If it is…

A: Consider the following free body diagram:

Q: Problem 4.1. A tensile load of 60 kN is gradually applied to a circular bar of 4 Cr er and 5 m long.…

A: Introduction: A tension load, the ratio of the applied force divided by the unit area that has a…

Q: 2. Consider a square bar 30 mm on side and 2.5 m long, having a material yield point 254 (in MPa).…

Q: Consider a square bar 30 mm on side and 2.5 m long, having a material yield point 254 (in MPa). An…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given Data: The distances are given as: u=2.8 mmv=5.7 mmc=620 mm The angles are given as: α=30°β=60°…

Q: signment #2: Determine Value of x if the Normal stress at rod is equal to rectangular pipe A =400…

A: Let the length be 'L'∑ Fy=0Trod+Tpipe-F=0forTrod=Tpipe2Trod-8=0Trod=Tpipe=4kN

Q: f the shaft?A

A: We knowμ=Lateral strainLongitudinal strainLateral strain=δddLongitudinal strain=δLL

Q: 29. During laboratory testing of an 8-inch aluminum-alloy rod with a cross sectional area of…

A: Given:- The length of the aluminum-alloy rod during testing = 8 inch The cross-sectional area of…

Q: Determine the stress produced in rod if tensile load of 3.3 N aplied on circular cross sectional…

Q: PROBLEM 1 Three 10mm wires are knotted at O and are in equilibrium. The forces exerted by each wire…

A: Given data in question 3 Forces are in equilibrium Angles Force value Diameter = 10 mm To find out…

Q: Two cast iron pipes are held together by a bolt as shown. The outer diameters of the two pipes are…

Q: 4. The figure below shows a copper rod that is placed in an aluminum tube. The rod is 0.0058 in.…

A: Given data in question Area Elastic modulus Length Stress To find out Maximum safe load

Q: The figure shows a drill-rig pipe that is being picked up by a crane at point C. The pipe has…

Q: Determine the absolute maximum bending stress in the 1.1-in.-diameter shaft which is subjected to…

Q: The beam is subjected to a shear of V = 13.5 kN. Set w = 125 mm. (Figure 1) Part A Determine the…

A: Given: The shear force in the beam is 13.5 kN. Consider the figure.

Q: 2.77 A steel rod 3 ft long with a cross-sectional area of 0.3 in.? is stretched between two fixed…

Q: 180 160 140 120 100 80 riator stress q (kPa)

Q: Calculate the normal stresses from the bending moment at the bottom point of cross-section C. Data:…

Q: A 20-m steel tape weighs 20 N. The tape is stretched between two points at the same elevation and…

A: Since the steel tape is stretched between two point, and has a self wt of 20 N. So there will be sag…

Q: Two 10 KN forces are applied to a 20xlo0 mm rectangular bar, as shown. stress at point A when (a)…

A: Given, Two forces=10 kN Dimension=20 mm×60 mm a) b=0 b)b=15 mm c) b=25 mm

Q: Determine the maximum shearing stress(MPa) that can be developed in a solid steel shaft if it will…

Q: A 2500 lb horizontal bar is supported by three 3/16-inch diameter wires as shown. The wires are…

A: Given:-P=2500 lb Diameter= 3/16 in L=20 feet=240 inches To find:- Stresses in wire Solution:-…

Q: A steel rectangular block 1in wide, 1/2in deep and 4in long is subjected to an axial tensile load of…

A: b = 1in wide d = 1/2in deep L = 4in P = ∆L = 2.8×10-2in∆b = .21×10-2in

Q: Using Stiffness Method, analyze 16 AN 20KN A E. I E. 1 51 E. 1 E, 1.5/ D. 2.0 1 20 m AE 2.0 m 4.0 m…

Q: Current Attempt in Progress Construct the shear-force diagram and identify the largest negative…

Q: A 30 m tape weighs 12 g/m and has a cross sectional area of 0.020 cm². It Q.2. measures correctly…

A: Length of tape = 30 m weight of tape = 12 g/m cross sectional area = 0.020 cm2 Standard pull = 85 N…

Q: The same torque is applied to two tub identical metal sheets, determine the circle/ of the shear…

Q: PROBLEM 4: The figure shows a plate that is fastened to a fixed to a fixed member by five 12-mm-…

Q: 420mm 850 mm b = 039 mm M = 6.5 KN.m E = 186 KN.m 1. Calculate the max. tensile and compressive…

Q: QUESTION: The distributed load on the T-section beam shown below and moment affects. A is the fixed…

Q: Find the shearing stress (in MPa) experienced by a rivet of radius r=16 mm if a shear force F =362…

Q: A load P is applied to a steel rod supported as shown by an aluminum plate into which a…

Q: Discussion: 1. Does plane section (square plane) on the surface of the circular shaft remain plane…

A: According to company policy we are obliged to do only the first question, please repost with the…

Q: Determine the maximum stress in the beam's cross section. Take M = 56 lb ft (Eigure 1) Express your…

A: Iz=bd312=46312=72in4Iy=64312=32in4My=56sin30=28lb-ftMz=56cos30=48.4974lb-ft

Q: A steel wire 10Om long hanging vertically supports a tensile load of 2000N. Neglecting the weight of…

A: Stress is the strength of the material per unit area of the cross-section. Also called as the…

Q: h В h h В t P+ 45° 45° B-B section

A: In the shown diagram below, the curved out bar has an axis that is circular (with mean radius r =…

Q: = 900 mm L, = 400 mm 1.27 Consider the stepped bar made with a linear elastic material and subjected…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: A hollow cast-iron pole has an outside diameter of 450mm and an inside diameter of 350mm. It is…

A: The given data is shown below: Outside diameter=450 mmInside diameter=350 mmCompressive force=1000…

Q: (c). A bar of length 1000 mm and diameter 30 mm is centrally bored for 400 mm, the bore diameter…

Q: Q. No .1 A solid 20-mm-diameter shaft is subjected to an axial load P. The shaft is made of aluminum…

A: Data given: Diameter of shaft (d) = 20 mm Modulus of elasticity (E) = 70 GPa Poison's ratio ν = 0.33…

Q: A solid 0.78-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A: Diameter of shaft = 0.78 in Determine the shear stress in shaft 3 =?

Q: A steel tape is 100m long at a standard pull of 65N. Compute the pull correction in mm if during…

A: Given : Length of Steel Tape (L)=100m Standard Pull (PS )=65N Applied Pull (PA) = 40N Cross Section…

Q: H.W find longitudinal and hoop tensile stresses in the Wall of vessel Shown in figure, if the…

A: Pressure=0.9MPa Thickness=6.4mm Diameter = 1.2m

Q: Q: 1: Write short notes on the following; I. Derive an expression for depth of Whitney's stress…

A: In the 1930s, Whitney (1937) proposed the use of a rectangular compressive stress distribution to…

Q: As in the given figure, a hole is to be punched out of a plate having a shearing strength of 40 ksi.…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Concept explainers

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.

Question

Determine poisson ratio

1. A metal rod 20 mm diameter and 2 m tong is subjected to a tensile force of 60
kN, it showed and elongation of 2 mm and reduction of diameter by 0.006 mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular steel rod of diameter d is subjected to a tensile force P = 3.5kN The allowable stress in tension and shear are 190.6 MPa and 70.3MPa, respectively. What is the minimum permissible diameter dmin of the rod (in mm)?
A 2500 lb horizontal bar is supported by three 3/16-inch diameter wires as shown. The wires are symmetrically spaced and 20 feet long. The two outer wires are steel and the middle wire is brass. Calculate: a) Stresses in the wires
The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the wood makes a 30.3º angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 20.2 MPa. Round off the final answer to four decimal places.
A steel flat 10 cm wide and 2 cm thick is bent into a circular arc of 50m radius.Find the maximum intensity of stress induced. Take E = 2.05 * 10 ^ 5 N/mm².
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The plate shown is fastened to the fixed member by eight 16-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 80 MPa. If P = 8200 N, what is the maximum and minimum shearing stress developed in the rivet.
Determine normal stress across plane passing through 50 degree to the plane 100 N/mm2
Calculate the value of the net tension area in square millimeters. NSCP 2015.
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
QUESTION: The distributed load on the T-section beam shown below and moment affects. A is the fixed joint and B is the sliding joint. This beam is made of a ductile material with a yield stress (σak) of 1000 MPa. The thickness (depth) of the beam profile is t=6 mm. A) As a mechanical engineer, check the strength of this beam (in terms of Normal and Shear Stress) ? B) In order for the existing beam to run smoothly, two 100x25 mm plates made of the same material are planned to be welded to this beam. The mechanical engineer working in the factory told the welder to weld this piece under the beam (where the B point is). But the welder, regardless of what the mechanical engineer said, welded this plate to both sides of the existing T-section beam as shown below, thinking that it wouldn't matter anyway. As a mechanical engineer : 1) After welding these plates on both sides of the beam, as the welder did, find out whether the new beam will work smoothly or not by making the necessary…
A 4.8ft-long steel wire of 1/4in-diameter is subjected to a 750lb-Tensile load. Knowing that E=29x10^6psi, determine (a) the elongation of the wire, and (b) the corresponding normal stress.
Determine the average normal stress in each rod if T2=400∘F Calculate the new length of the aluminum segment.
Calculate the bending stress and shear stress values and draw the stress diagrams next to the section. T=10tons,M=-14tm,b=45mm,h=880mm,t=60mm