1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, mass flow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following: (a) ideal turbine work (b) ideal pump work (c) theoretical thermal efficiency

1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, mass flow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following: (a) ideal turbine work (b) ideal pump work (c) theoretical thermal efficiency

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 540 degree celsius, condenser pressureis 0.034 bar, mass flow rate of steam is 12 kg/sec. Draw the T-S and Schematic diagram of cycle and determine the following: a. Ideal turbine work b. Ideal pump work c. Theoretical thermal efficiency d. The steam rates e. Heat rate of the cycle f. Pump Work g. Turbine Work
Q#1. A gas-turbine plant operates on the regenerative Brayton cycle, the schematic diagram of whichis shown in Fig. Q 1, with two stages of reheating and two-stages of intercooling between the pressure limits of100 and1200 kPa . The working fluid is air. The air enters the first and the second stages of the compressor at 300 K and 350 K , respectively, and the first and the second stages of the turbine at 1400 K and 1300 K , respectively. Assuming both the compressor and the turbine have an isentropic efficiency of 80%. The regenerator has an effectiveness ofεregen=75% . Assume variable specific heats (i.e., use the concept of relative pressures) and the intermediate pressuresof intercooling and reheating is the square root of the product of inlet and exit pressures for intercooling and reheating. Make other the necessary assumptions and determine(a) the back work ratio,β , and the net work output,, wnet(b) the thermal efficiency (that is the first-law efficiency,ηi ) and(c) the…
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. Determine the enthalpy of steam entering the reheater.
An ideal Rankine cycle operates between the pressure limits of 15,000 kPa in the boiler and 15 kPa in the condenser. If the turbine inlet temperature is 500 deg C and the cycle produces 2500 kW of net work, determine the mass flow rate of the steam in kg/s. Refer to the tables below. a. 1.993 b. 2.122 c. 1.856 d. 2.016
The mass flow rate of steam is 5 kg/s for a Rankine Cycle. For the actual cycle, the turbine efficiency is 86%, turbine brake efficiency is 80%, and generator efficiency=90%. The inlet conditions of the turbine are 3MPa and 400⁰C while the condensing pressure is 50kPa. a. Sketch the P-v, T-s and h-s diagram of the Cycle b. Calculate for the ideal and actual steam rates and heat rates of the Rankine Cycle and Rankine Engine, respectively. c. Determine the energy chargeable and combine thermal efficiencies for the Rankine Cycle and Rankine engine, respectively
Steam enters the high-pressure turbine of an ideal reheat Rankine cycle at 10 MPa and 500°C. The low-pressure turbine inlet admits steam at 1 Mpa. Assume that the pump inlet is a saturated liquid at 10 kPa and that 80 MW of power is produced overall. 1. Report the overall thermal efficiency of the cycle as a percentage (number between 0 and 100) to one decimal place using rounding. 2. Report the mass flow rate, in kg/s, to one decimal place using rounding.
1. In a Rankine cycle, steam enters the turbine at 2.5 MPa and condenser at 50 kPa, what is the thermal efficiency of the cycle?At 2.5 MPa: hg = 2803.1 kJ/kg sg = 6.2575 kJ/ kg – KAt 50 kPa: sf = 1.0910 sfg = 6.5029hf = 340.49 hfg = 2305.4vf = 0.0010300
27 - In the simple ideal Rankine cycle, the enthalpy of water at the turbine exit is 2300 kJ/kg. If the pressure at the turbine inlet is 8 MPa and the temperature is 550ºC, which of the following should the water flow rate be to obtain 110 MW power? a) 100kg/h B) 120kg/h NS) 110 kg/h D) 130kg/h TO) 90kg/h
Consider a simple Brayton cycle that uses air as the working fluid to operate a gas-turbine power plant between the pressure limits of 100kPa and 900kPa. Air enters the compressor at 298K and leaves at 610K at a mass flow rate of 1200kg/min. The maximum cycle temperature is 1380K. The net power output from the cycle is measured experimentally to be 55 MW. Assuming constant properties (Cv,Cp, R, and k) for air at 300K: a) Sketch a T-s diagram for the cycle b) Determine the isentropic efficiency of the turbine c) Determine the thermal efficiency
1.5An ideal Rankine cycle with reheat uses water as the working fluid. As shown in the figure below, the conditions at the inlet to the first turbine stage are 1600 lbf/in.2, 1200°F and the steam is reheated to a temperature of T3 = 800°F between the turbine stages at a pressure of p3 = p2 = 200 lbf/in.2 For a condenser pressure of p5 = p4 = 1 lbf/in.2, determine:(a) the quality of the steam at the second-stage turbine exit. h6≈h5+v5(p6−p5)h6≈h5+v5(p6-p5)Determine the quality of the steam at the second-stage turbine exit. x4 =(b) the cycle percent thermal efficiency.
35 - In the simple ideal Rankine cycle, the enthalpy of water at the pump outlet is 230 kJ/kg. If the pressure at the turbine inlet is 9 MPa and the temperature is 400ºC, which of the following should be supplied to the water at a flow rate of 50 kg/s? a) 225.5 MW B) 199.7 MW NS) 259.1 MW D) 224.8 MW TO) 144.4 MW
In an ideal Reheat cycle , the steam throttled condition is 7 Mpa and 460 C. The steam is then reheated to 1.5 MpA and 460 C . If turbine exhaust is 50 C ,determine the following: A.) Quality after turbine expansion B.) Turbine work C.) Heat added in the boiler D.) Heat rejected from the condenser E.) Pump work F.) Net work G.) Cycle efficiency