1. A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 kN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteei = 200 GPa. %3! %3D

1. A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 kN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteei = 200 GPa. %3! %3D

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.11P

See similar textbooks

Similar questions

a tank with its contents weighs a 5000kg. It will be supported by four concrete posts equally spaced and with outer edges flushes with the perimeter of the tank. The compressive strength of the concrete posts is 1000 psi and a factor of safety of 4 is required. calculate the diameter of each post in cm.
A rectangular concrete beam 320 mm wide and 449 mm deep is simply supported over a span of 11.75 m. the beam is reinforced with straight tendons situated 56 mm above the bottom of the beam under a prestressing force of 631 kN. Concrete weighs 23.12 kN/m3 with modulus of elasticity Ec=21,212.29 MPa. Assuming tension concrete does not crack, what is the midspan deflection due to the given loads.
Calculate the corresponding depth of uniform stress block in a reinforced concrete beam 40*10 deep reinforced with the bars 20mm in diameter enclosed with 10mm diameter stirrups when the tensile steel strain is 0.008 and concrete strain is 0.003. f'c = 22MPa.
The reinforced concrete beam has the cross-sectional area shown in the figure with b =12 in., d=16 in., ? steel= 1.571 in.2, determine the largest bending moment that may be applied safely. Takethe elastic moduli ?steel=29(10^3) ksi and ?concrete= 3.6(10^3) ksi. The working stresses are2.39ksi for concrete and 22.145ksi for steel.
Calculate the corresponding depth of uniform stress block in a reinforced concrete beam 47*10 deep reinforced with bars 20-mm in diameter enclosed with 10-mm-da stirrups when the tensile steel strain is 0.008 and concrete compression strain is 0.003. f'c= 23 MPa. Express your answer in 2 decimal places only in mm.
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit) What is the actual shearing stress of the beam in MPa? (use two decimal places, no need for unit)
The floor system of a residential building consists of 125mm thick concrete slab (unit weight = 23.6 KN/m^3) resting on the three 8 m spanned RC floor beams spaced at 1.7 meters on center. Size of RC beam is 200mm x 450mm. NSCP 2015 load Factors: 1.2DL & 1.6LL. Assume simple supports. Calculate the unfactored slab in KN/m? Express your answer in 1 decimal places.
If possible, answer in 3 decimal places, thank you. For the wood beam shown in Figure A, assume L=1.5 m and P=8 kN. The beam cross section shown in Figure B has dimensions of b=47 mm and d=232 mm. (a) Determine the maximum horizontal shear stress in the beam. (b) If the allowable shear stress for the wood is 800 kPa, what is the minimum width b that is acceptable for this beam? Calculate the reaction forces By and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown for the forces By and Dy on the free-body diagram below. (Note: Since Dx=0, it has been omitted from the free-body diagram.) By= kN Dy= kN Determine the shear forces VA⁢B, VB⁢C, and VC⁢D acting in segments AB, BC, and CD, respectively. Note that the shear force is constant in each of these segments. When entering your answers, use the shear force sign convention. VA⁢B= kN VB⁢C= kN VC⁢D= kN…
calculate the corresponding depth of uniform stress block in a reinforced concrete beam 45x10 deep reinforced with bars 20mm in diameter enclosed with 10-mm-dia stirrups when the tensile steel strain is 0.008 and concrete compression strain is 0.003 f’c=27MPa
The figure shows the cross section of a circular steel tube that is filled with concrete and topped with a rigid cap. Calculate the stresses in the steel and in the concrete caused by the 200-kip axial load. Use Est = 29 x 106 psi and Eco = 3.5 x 106 psi.
1.A steel column supports an axial compressive load of 400 kn. Determine the inside diameter of the column if its outside diameter is 250mm and the allowable compressive stress is 68 MPa
1. A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 KN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteel = 200 GPa.