1. A square-wave inverter has an R-L load with R 15 2 and L. 10 mH. The inverter output frequency is 400 Hz (a) Determine the value of the de source required to establish a load current which has a fundamental frequency component of 10 A rms. (b) Determine the THD of the load current. (c) Sketch the output and input currents.

1. A square-wave inverter has an R-L load with R 15 2 and L. 10 mH. The inverter output frequency is 400 Hz (a) Determine the value of the de source required to establish a load current which has a fundamental frequency component of 10 A rms. (b) Determine the THD of the load current. (c) Sketch the output and input currents.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a series inverter circuit for operation in the frequency range 50Hz to 90 Hz. The load resistance may vary from 20 Ohm to 80 Ohm. :Thepeak load current is limited to 4 A and the supply voltage is 120 V
The general procedure for inverter setup is to check? And current levels from the source (modules) to inverter closing disconnects as needed to accomplish this. A. ampacity B. wattage C. voltage D. conduction potential
Single-phase full-bridge inverter is connected between a 200 V d.c. source and a series connected R-L load with R = 20Ω and L = 50 mH. The inverter frequency is 50 Hz. Determine the values of the rms load current, the load power and the total harmonic distortion factor, up to the 9th harmonic.
A DC link inverter has an AC rms line input of 600 V, 50Hz. The inverter load is a balanced star connection of 195Ω resistors.Determine load current and power for a converter firing angle delay ofa) Determine load current, voltage and power for a converter firing angle delay of 12.5 degrees.b) Determine load current, voltage and power for a converter firing angle delay of 62 degrees.
1. A square-wave inverter has an R-L load with R=15 Ω and L=10 mH. The inverter output frequency is400 Hz (fundamental frequency).(a) Determine the values of the required to establish a load current which has a fundamentalfrequency component of 10 A rms with α = 0.(b) For a controlled full-bridge inverter, the dc source is 125 V and the switching frequency is60 Hz. Determine the value of α to produce an output with amplitude of 100 V at the fundamentalfrequency.
1. A single phase half-bridge inverter, connected to 230V dc source, feeds a resistive load of 10Ω. Determine (a) fundamental rms output voltage (b) total output power and fundamental frequency power (c) average and peak currents of switches (d) input pf. 2. Discuss 1200 mode of conduction for a 3ph-phase VSI. Also, derive the expression for the outputvoltage and draw waveforms for phase voltages, line voltages and voltage across one switch.
Q1) The square-wave inverter has a dc input of 150 V and supplies a series RL load with R-20 Ω and L = 40 mH.(a) Determine an expression for steady state load current.(b) Sketch the load current and indicate the time intervals when each switch component (Q1, D1:.. Q4, D4) is conducting.(c) Determine the peak current in each switch component.(d) What is the maximum voltage across each switch?
1 phase half bridge inverter having dc input voltage 300V , and purely resistive load R = 2.4 ohm , find :Vrms for the first harmonic fundamental load power: average supply current if the power delivered by each source is 3.8 kw :
1. In a full-bridge single-phase inverter with an input voltage of 200V and a switchingfrequency of 4kHz, the power of a 16Ω load is controlled by the method of a gappedsquare wave control. Ignoring the circuit losses, answer the following questions a. Draw the inverter circuit presented in the question b. Generate PWM signals for a duty ratio of ½. Draw the load voltage, load current. Drawthe current and the voltage of any of the semiconductors. Find the load voltage. Find theoutput voltage frequency c. Find the nominal (the maximum) power and current of the load d. Find the duty ratio to get half of the nominal voltage e. Find the duty ratio to get a quarter of the nominal power f. Find the average value and effective value of BJT current for the case of item-e
Redesign the resistive load inverter for operation at a power level of 0.30 mW withVDD = 3.3 V. Assume VT O = 0.7 V. Keep theother design parameters the same. What is the newsize of MS and the value of R? (b) What are thevalues for NMH and NML ?
For a single phase inverter has the following parameter ;Vdc = 80v , R = 8Ω , L = 20mH and F = 60Hz , Determine totalharmonic distortion for n = 5 then write expression for voltage
The single-phase half-bridge inverter has a resistive load of R = 2.4Ω and the DCinput voltage is 48V. Determine:1- the rms output voltage at the fundamental frequency2- fundamental displacement factor .3- fundamental power , drown from each source .4- fundamental load power .5- total power drown from each source .6- total load power .