1. A steel bar is subjected to the loads shown in the figure. Determine the total deformation in the bar (E=210 GPa, A=50 mm²) . (Point A is fixed support) BC mm CA mm C AB mm |A B D CB mm E АB KN AC kN ВС KN CB kN

1. A steel bar is subjected to the loads shown in the figure. Determine the total deformation in the bar (E=210 GPa, A=50 mm²) . (Point A is fixed support) BC mm CA mm C AB mm |A B D CB mm E АB KN AC kN ВС KN CB kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Draw a free body diagram of rigid bar ABD, and determine the magnitude of the vertical reaction force at pin D.Answer:D = kN
The steel truss shown carries a downward vertical load of 14 kN at joint B. The diagonal members of the truss have an area equivalent to 250 mm^2, and the horizontal members are 300 mm^2. With the given conditions calculate the: a) Horizontal Deflection at E in mm b) Vertical Deflection at D in mm Esteel = 200 GPa
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
Find. (1) Maximum bending stress at point B (2). Calculate deflection at point B.
2.Determine the vertical displacement of joint A (a) if members AB and BC experience a temperature increase of ΔT = 200°F. Take A = 2 in^2 and E = 29(10^3) ksi. Also, a = 6.60 (10^-6)/°F. (b) if member AE is fabricated 0.5 in. too short. Include the effect of external forces in both cases.
Question 1) F=20 kN single load, M=23 kN.m moment and w=19 kN/m distributed load are acting on the beam whose loading condition is given in the figure . The length L is also given as L=5 m . The cross-sectional properties of the beam are; body height y g =248 mm , body thickness x g =12 mm , flange width x f = 196 mm , flange height y f = 20 mm . Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question1-A ) Find the normal force (N C ) at point C. ( Write your result in kN .) Question1-B ) Find the shear force (V C ) at point C. ( Write your result in kN .) Question1-C ) Find the bending moment ( MC) at point C. ( Write your result in kN.m. )
A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Determine the internal force and the change in length of section (1) of axial member CDE. Tension and elongation are positive. Compression is negative.Answer:F1 = kNδ1 = mm
Determine the vertical displacement of joint D. Each A-36 steel member has a cross-sectional area of 400 mm2.
Determine thy vertical displacement (mm) of joint B. Support A is roller and support D is hinge. A=2500 mm2 E=200 GPa
A cantilever beam supports the loads shown. The cross-sectional dimensions of the shape are also shown. Assume a = 0.6 m, PA = 2.5 kN, PB = 7.0 kN, PC = 4.0 kN, d = 100 mm, bf = 110 mm, tf = 10 mm, tw = 7 mm. Determine(a) the maximum vertical shear stress.(b) the maximum compression bending stress.(c) the maximum tension bending stress. See the coordinate system for the beam in the problem figure with the origin of the x axis at the fixed support. Consider four points along the beam’s axis:Point A at x = 1.8 mPoint B at x = 1.2 mPoint C at x = 0.6 mPoint D at x = 0Break the beam into three segments: AB, BC, and CD. Enter the shear force in each segment with its correct sign based on the coordinate system in the problem figure and the sign convention for shear forces in Chapter 7.Answers: VAB = kN VBC = kN VCD = kN Enter the maximum shear force magnitude in the beam. Since this is a magnitude, enter a positive value.Answer: Vmax = kN Enter the…
A part of slab is given in the figure. The slab is supported by secondary beams AB, CD and EF which are placed with a 50cm spacing. The secondary beams transfer the load they carry to the main beams.In the figure, AE and FB are the visible part of the main beams. Finally, main beams are supported by the columns at both ends. The slab is under uniformly distributed load q=4.5 kN/m2. The span length L is 3,5 m. Determine the dimendions of rectengular cross-sections of timber beams CD and the main beam which has a length of 4 m.
A cantilever beam AB with a circular crosssection and length L = 750 mm supports a loadP = 800 N acting at the free end (see figure). Thebeam is made of steel with an allowable bendingstress of 120 MPa.(a) Determine the required diameter dmin (figurepart a) of the beam, considering the effect of thebeam’s own weight.(b) Repeat part (a) if the beam is hollow with wallthickness t =d /8 (figure part b); compare thecross-sectional areas of the two designs.