SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b C Steel: A=900 mm² E=200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? 0.367 0.433 O 0.467 0.333

SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b C Steel: A=900 mm² E=200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? 0.367 0.433 O 0.467 0.333

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

As shown in figure, the allowable stress for tension is 200 MPa and the allowable stress for compression 250 MPa. Please find the largest couple M that can be applied. Please make your choice and explain the reason.
A cylindrical rod AB has a length ? = 80 cm and a diameterof ? = 2 cm. The modulus of elasticity is ? = 200 GPa andyield strength is ?? = 300 MPa. The stress-strain diagram ofthe rod is shown in the left figure. A force ? = 100 kN isapplied to the bar and then fully removed (right figure).Determine the permanent set in the rod.
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P is equal to 51kips)
Considering the steel rod at E, how long will its elongation be if it is hollow with an outside diameter of 25 mm and a thickness of 1.5 mm? Use E=200 GPa
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of the external diameter of 3.6 cm and an internal diameter of 2 cm. The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.5 cm from the neutral axis Solution: (i) The moment of inertia = Answer and unit for part 1 ii) The radius of curvature is Answer and unit for part 2 (iii) The maximum bending stress is Answer and unit for part 3 iv) The bending stress at the point 0.5 cm from the neutral axis is
A rigid block weighing 196.6 kN is attached as shown in the figure. Properties of materials are as follows: for steel A = 660 mm2, E = 200 GPa; for bronze A = 910 mm2, E = 83 GPa. The block is to remain horizontal with a = 0.8 m and b = 1.2 m. Calculate the tensile force in the steel rod in kN.
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. where P=25 .
1. The figure below shows a roof canopy beam which is supported by a φ20 mm hanger rod. The roof beam is a W200×19 steel beam with a cross-sectional area A = 2480 mm2, section modulus, Sx = 163×103 mm3 and a moment of inertia Ix = 16.6×106 mm4. The modulus of elasticity for steel is 200 000 MPa. 1) Determine the beam reactions at A and B. 2) Determine the axial stress in the 20 mm hanger rod and in the W200x19 beam. 3) Determine the shear force and bending moment at the midspan of the beam 4) Determine the bending stress in the beam at the mid-span of the beam.
Three uniform 1-meter bars weighing "W" each are welded together as shown. The bars are suspended by three vertical wires. Bars AB and BC lie in the horizontal x-y plane, and the third bar lies in a plane parallel to x-z plane. If the tension at B is 250 N, determine the value of w (in kg) and the tension in A and C.
A rod is composed of 3 segments shown in the figure and carries the axial loads, P1=120KN and P2=50KN. If the walls are rigid, determine the stress of bronze, aluminum, and steel in MPa.
The figure shows a single acting rivet connecting steel plates. Rivet diameter d = 22 mm,plate thicknesses are t1 = 20 mm, t2 = 12 mm, plate width b = 100 mm and e = 38 mm. The shear strength in the material is τem = 100 MPa, the safety stress in pressure and tension is σL = 280 MPa andSince σem = 140 MPa, determine the maximum force P that the joint can safely carry.
A bar of 30 mm diameter is tested in tension. It is observed that when a load of 80 kN is applied, the extension measured over a gauge length of 200 mm is 0.20 mm and contraction in diameter is 0.005 mm. Find Poisson’s ratio and elastic constants E, G, K.