1. A uniformly thick control gate in a 2 m wide fresh water channel is hinged at A as shown. Determine theweight, W, of the gate so that it will just open when the water reaches a depth of 1.2 m.2. 81.2mo.8mस ्3

A uniformly thick control gate is there whose width is 2 m we need to determine the weight, W of…

1. A uniformly thick control gate in a 2 m wide fresh water channel is hinged at A as shown. De weight, W, of the gate so that it will just open when the water reaches a depth of 1.2 m. 2.8w 1.2m o.8m

1. A uniformly thick control gate in a 2 m wide fresh water channel is hinged at A as shown. De weight, W, of the gate so that it will just open when the water reaches a depth of 1.2 m. 2.8w 1.2m o.8m

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.18P: For the data given in this problem, determine the magnitude of the active thrust on the wall...

See similar textbooks

Related questions

Q: if the pavementis with 6 inclination, what will be the braking distance (in meter) of the car going…

Q: NO. 30 KN/m DATE Hinge 1.6m 200 KN 10.4 m K-6m米一 Which of the following gives the vertical reaction…

A: Three Hinged Arch is Determinate structure having one equilbrium equation at the crown where bending…

Q: identify Wastewater standards, Advanced biological treatment systems and its processes

A: Introduction- Wastewater treatment system- This system is used to treat the wastewater from…

Q: The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD…

A: TAB=800N-mTBC=2400N-mTCD=2400N-m

Q: Calculate the maximum force that a 2.5mm thick and 50mm wide nickel strip, having a yield strength…

Q: A Simple Curve has a Central Angle of 60 deg and a Degree of Cu a. Find the nearest distance from…

A: A sample curve has a central angle is given and the degree of curve is also given we need to find…

Q: A spillway 38.9 ft long releases flood run-off from a reservoir 46,000 m² in area. The initial head…

Q: 3 2 -1 Rank of the following matrix is A = | 4 2 7 4 5

A: Convert the matrix into upper triangular matrix and number of non zero rows will give the rank of…

Q: Example 4.5 4.8 m. The member is to be used in a transmission line tower and is as shown ends are…

Q: An intersection approach has a saturation flow rate of 1500 veh/h, and vehicles arrive at the…

Q: 30. Without using the Table of Concrete Proportion, for eight (8) cum of Class B concrete mix…

Q: isk? A weakness in a system Any potential danger that is associated with the exploitation of a…

A: this question is asking about best definition security risk.

Q: The braking distance of a car from 90 km/h is 40 m assuming the pavement is level. (a) if the…

Q: 1. A 200mm x 300mm beam has a simple span of 8 meters. It is necessary to place a support at midspan…

Q: Problem 4: Members AB and BC can each support a maximum compressive force of 750 lb, and members AD,…

Q: Determine the acceleration of each body and the tension in the cord supporting block A. Coeff…

Q: A soil sample has a maximum void ratio of 0.95 and minimum void ratio of 0.55. It was also found out…

Q: The floor of a structure is to support 40psf live load and 10psf dead load. The supports will be 2x…

A: Given data The joist are given.

Q: 5. The beam shown is resting on two moveable supports. It carries a uniform love load of 120 N/m and…

Q: 8.11 It takes a certain length of time for the liquid level in a tank of diameter D to drop from…

A: tank of diameter D liquid is nonviscous

Q: A property line VY intersects a simple curve at point W whose radius is 120 m long. The property…

A: Solution (a) Distance VX ∠VXZ = 3600 -2200 -600 = 800 ∠ZVX = 1900 -1800 + 600 = 700 ∠VZX = 1800…

Q: Determine the member force on member IJ.

Q: A burglar's car had a start with an acceleration of 2 m/s. A police vigilant party came after 5…

Q: to E

Q: Calculate "P" in KN considering tension failure on net area Two A36 16mm Thick Steel Plates Are…

Q: 4. A compound lever shown in Fig. 3.22 is required to lift a load of 9 kN with an effort P. A F1 D…

A: The problem can be solved using equilibrium equations. Draw free body diagram in parts then summing…

Q: The tangents of a sag curve connects at the point of intersection having Station 18+427.14 and…

A: Sag Curve: Sag Curve is the vertical curve that generally connects the descending curve. Sag…

Q: identify drinking water standards, Overview of typical processes used for contaminant removal,…

A: Brief concept introduction- Preliminary treatment processes- Preliminary treatment is the process of…

Q: 1. Find the skin friction capacity of pile if frictional constant is 0.76. a. 1360.2 kN b. 1723.68…

Q: The time derivates of the equation that related the velocities of the particles yields a similar…

Q: Solve for TA, aA, aB, and aC

A: Free body diagram (FBD): - It is a diagram in which one can see all the forces acting on an object…

Q: 3. Two beams are supported as shown in the diagram below, each 150mm x 200mm x 4 meters. Beam CD is…

Q: The second floor of a light manufacturing building is constructed from a 125 mm thick stone concrete…

Q: The force vs. elongation relationship for a given body is dependent on the body's geometry as well…

Q: rectangular weir contracted both ends installed across a rectangular channel 10.27 m wide. If the…

A: Given. Discharge Q 3 m3/ sec Width 10.27 m Coefficient of discharge for rectangular weir contracted…

Q: Please

Q: A trapezoidal flume of most efficient proportion has base width of 1.5 m. Its full discharge is 3…

Q: Given four vectors: 16 newtons 20 degrees north of west; 25 newtons due south; 10 newtons due east;…

Q: The variation of the total volume ( V ) of a specimen of a fine soil with its water content ( w) is…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: NEED ASAP SOLUTION. PLOT CURVE A vertical summit curve is having tangents which intersects at point…

A: PVCSTATION=PVISTA-L212500.65=12609.84-L2L=218.38mPVCELV=PVIELV-g1L2115.52=139.82-g1×218.382g1=22.254…

Q: lap splicing

A: A lap splice is when two pieces of rebar overlap to form a continuous reinforcement. This helps…

Q: A small town has been divided into three trafficzones. An origin-destination survey was conducted…

Q: In the system of connected blocks in the figure, the coefficient of kinetic friction is 0.20 under…

Q: Q3. Draw bending moment diagrams for the following rigid frame structure shown in the figures by…

Q: The results of a plate-load test in a clay soil are shown below. The size of the plate is 0.41m x…

A: Clayey soil Plate size .41m * .41 m Foundation size 3*3 m Load 2700kn Settlement of foundation ?

Q: Explain LAP SPLICING. Illustrate a sample figure about it.

Q: Determine the member force in AB? 10 kN 6 m 3m 3 m D 60 kN

A: To Find :- Force in member AB.

Q: A concrete spillway which is used to control a reservoir area of 4 hectares has a permanent crest…

Q: 4m 6m 10m 5m 15m D B 40KN 60KN

Q: The figure as shown below is a rigid bar which is supported by two rods and a pin support. If the…

Question

1. A uniformly thick control gate in a 2 m wide fresh water channel is hinged at A as shown. Determine the
weight, W, of the gate so that it will just open when the water reaches a depth of 1.2 m.
2. 8
1.2m
o.8m
स ्
3

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2:Calculation

VIEW

Step 3:Further calculation

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A vertical, trapezoidal gate in the face of a dike is subjected to sea water pressure (s =1.3) on one side. The upper edge is in the water surface and is 1.567 meters long. Twoedges are vertical and measured 2.67 meters and 3.76 meters each. Determine the totalpressure on the gate and the location of the center of pressure.
A gate slanted 60 degrees from the horizontal with width = 1.6 m and height = 2.4 m is submerged by a depth of 1.8 m, determine the pressure at the top of the gate in Pa.
A wall footing 1 m wide carries a uniform load of 300 kN/m of wall length. Soil weights 16 kN/m^3.Using the influence chart, compute the total vertical increment of the loads at a depth of 3 m from the edge of the strip in kN/m. a. 48 b. 60 c. 156 d. 108
When the tide water A subsides, the tide gate automatically swings open to drain the marsh B. For the condition of high tide shown, determine the horizontal reactions developed at the hinge C and stop block D. The length of the gate is 6 m and its height is 4 m. ρw = 1.0 Mg/m3.
1. A trapezoidal channel has a bottom width of 6 m and side slopes of 2H:1V. If thedepth of flow is 1.2 m and the flow is 20.40 m3/s,a. Compute the specific energy b. Compute the slope of channel if n = 0.014 c. Compute the average shearing stress at the boundary
A verical gate 1.6m wide and 2m high has water on side and is inclined 45° with the horizontal. Water is 1.50m above the top of the gate. With the gate hinged at B. Determine the hydrostatic force acting on the gate
A circular door having a diam. of 3m closes a horizontal duct from a small diam. as shown. The center of the door is 4.5m below the dam’s water level. Assuming the unit weight of water is 9.79 kN/m3. Compute the hydrostatic force acting on the door.
A vertical gate 1.50 m wide and 2.0 m high has water on one side and is inclined 45° with the horizontal. Water is 1.60 m above the top of the gate where the hinge support is located. a. Compute the hydrostatic force acting on the gate b. Compute the location of the center of pressure from the bottom.
A gate slanted 60 degrees from the horizontal with width = 1.6 m and height = 2.4 m is submerged by a depth of 1.8 m, determine the pressure at the top of the gate in Pa. Use whole number.
A concrete gravity dam has the following data: Maximum water level = 300.00 m Bed level = 220.00 m R.L top of dam = 304.00 m %3D The d/s slope of 0.67:1 starts at RL of 295.00 m U/s face is vertical. Center line of the drainage gallery = 8.0 m from u/s face. Consider only weight of dam, water pressure and uplift pressure. Calculate only the normal stresses at the toe and heel of the dam, assuming 100% uplift pressure at the h eel and 50% at the gallery and zero at the toe.
The figure shows the section of weir, the base of which is 1.5m below the ground. The necessary flow net has also been drawn. a) Find the uplift pressure at Point A. b) Compute the uplift pressure at Point B. c) Determine the total uplift force per meter width under the weird
Water flows through the 2-in-diameter pipe at 0.2 ??^3/s as shown in Fig. 5-19a. If the pressure at A is 30 psi, determine the pressure at C, and draw the energy and hydraulic grade lines from A to B. Neglect friction losses and take ?? = 62.4 ??/ft^3