The second floor of a light manufacturing building is constructed from a 125 mm thick stone concrete slab with an added 100 mm cinder concrete as shown. If the suspended ceiling of the first floor consists of metal lath and gypsum plaster, determine the dead load for design in kN per square meter of the floor area.

The second floor of a light manufacturing building is constructed from a 125 mm thick stone concrete slab with an added 100 mm cinder concrete as shown. If the suspended ceiling of the first floor consists of metal lath and gypsum plaster, determine the dead load for design in kN per square meter of the floor area.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The second floor of a light manufacturing building is constructed from a 5-in.-thick stone concrete slab with an added 4-in. cinder concrete fill as shown. If the suspended ceiling of the first floor consists of metal lath and gypsum plaster, determine the dead load for design in pounds per square foot of floor area.
The interior wall of a building is made from 2 x 4 wood studs, plastered on two sides. If the wall is 12 ft high, determine the load in lb/ft of length of wall that it exerts on the floor. Check the minimum design dead load table for the unit weight.
A floor of a heavy storage warehouse building is made of 150-mm thick stone concrete. The floor slab is 4.5 m in length by 3m wide. Determine the service dead load and liv
The floor of a heavy storage warehouse building is made of 6-in.-thick stone concrete. If the floor is a slab having a length of 15 ft and width of 10 ft, determine the resultant force caused by the dead load and the live load.
The floor of a heavy storage warehouse building is made of 6-in thick stone concrete. If the floor is a slab having a length of 15 ft and width of 10 ft. Determine the resultant force cause by the dead load and the live load.
Need to consider the live load reduction
A floor has a load of 150psf distributed to columns spaced at 24ft in one direction and 40ft in the other. Find the floor load on an EXTERIOR CORNER column.
A column in the upper story of a residential building is subjected to a compressive load from the following sources: dead load = 35 kN, occupancy live load = 4.8 kN, roof live load = 21 kN, and rain load = 22 kN. 1. If load and resistance factor design is used, compute the factored load to be used in the design of the column. Which NSCP load combination controls? a. ?.?(?+?) b. ?.?(? + ? + ?) + ?.?(? + ?) + ?.?(?? ?? ?) c. ?.?? + ?.?(?? ?? ?) + (??? ?? ?.??) d. ?.?? + ?.?? + ??? + ?.?(?? ?? ?) e. ?.?? + ?.?? + ??? f. ?.?? + ?.?? + ?.?? g. ?.?? + ?.?? + ?.?? 2. What is the value of the required design strength of the column in Item 1? 3. What is the required nominal strength of the column in Item 1 for a resistance factor of 0.90? 4. If allowable strength design is used, compute the required load capacity to be used in the design of the column. Which NSCP load combination controls? a. ? + ? b. ? + ? + ? + ? + ? c. ? + ? + ? + (?? ??…
the floor of a light storage warehouse is made of 15-mm thick lightweight plain concrete. if the floor is a slab having a lenght of 7m and the width of 3m. determine the resultant force cause by the dead and their live load
The precast floor beam is made from concrete having a specific weight of 23.6 kN/m3 . If it is to be used for a floor of an office building, calculate its dead and live loadings per foot length of beam.
The partial plan layout for the framed structure of a multistory building is shown below. The vertical structure consists of columns and the horizontal floor structure of a one-way deck and beam system. The uniformly ultimate (factored) distributed load for the one-way-spanning deck is equal to 0.14 kip/ft2. Ignore the own weights of beams and walls. L1 = 22 ft, L2 = 22 ft, L3 = 32 ft. Compute the load on column 1. Compute the value of distributed load on beam A. Compute the value of concentrated loads on beam C. Draw the shear and bending moment diagrams for beam C (with values) – Assume beam C as simply supported.
A 5m reinforced concrete beam, with dimensions 300 mm x 500 mm, has a superimposed dead load of 20kN/m and a live load of 10kN/m. If the unit weight of concrete used in the beam is 24 kN/m^3, what would be the total service load carried by the beam?