1. An air-standard Diesel cycle has a compression ratio of 15 and a cutoff ratio of 1,4. At the beginning the compression process, air is at 97 kPa and 17°C. Accounting for the variation of specific heats wi temperature, determine, a. the temperature after the heat-addition process, b. the thermal efficiency, and MEP c. the entropy generation of the engine

1. An air-standard Diesel cycle has a compression ratio of 15 and a cutoff ratio of 1,4. At the beginning the compression process, air is at 97 kPa and 17°C. Accounting for the variation of specific heats wi temperature, determine, a. the temperature after the heat-addition process, b. the thermal efficiency, and MEP c. the entropy generation of the engine

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an air standard dual cycle two –thirds of the total heat supply occurs at constant volume. The state at the beginning of the compression process is 90kPa and 20°C and the compression ratio is 9. if the total heat supply is 2100kJ/kg, Determine the maximum pressure of the cycle and maximum temperature of the cycle.
2. The compression ratio of an air-standard Otto cycle is 9.5. Prior to the isentropic compressionprocess, the air is at 100 kPa, 35°C, and 600 cm3. The temperature at the end of the isentropicexpansion process is 800 K. Using specific heat values at room temperature, determine (a) thehighest temperature and pressure in the cycle; (b) the amount of heat transferred in, in kJ; (c)the thermal efficiency; and (d) the mean effective pressure.
Consider a Diesel cycle with cold-air-standard assumptions, and compression ratio of 21. The temperature and pressure at the beginning of the compression process are 320K and 120kPa respectively. The cutoff ratio for this cycle is 1.8. The isentropic efficiency of the compression and expansion process are 85%. Determine the temperature and pressure at the end of each process of the cycle, the heat transfer per unit mass in and out of the air; qin and qout, thermal efficiency of the cycle, and the mean effective pressure of the cycle.
An air-standard Diesel cycle has a compression ratio of 16 and a cutoff ratio of 2. At the beginning of the compression process, air is at 95 kPa and 27°C. Accounting for the variation of specific heats with temperature, determine the temperature (in K) after the heat-addition process. Note: @T = 300K, u = 214.07kJ/kg, v = 621.2.
An ideal Diesel cycle has a compression ratio of 18. Air is at 27°C and 100 kPa at the beginning of the compression process and at 1800 K at the end of the heat addition process. Determine the cutoff ratio, determine the heat rejection per unit mass, in kJ/kg, determine the thermal efficiency of the cycle. (Apply air-standard assumptions: variable specific heat)
The compression ratio of an air-standard Otto cycle is 9.5. Prior to the isentropic compression process, the air is at 100 kPa, 35°C, and 600 cm³. The temperature at the end of the isentropic expansion process is 800 K. Using specific heat values at room temperature, determine the mean effective pressure.
An air-standard Diesel cycle has a compression ratio of 16 and a cutoff ratio of 2.5. At the beginning of the compression process, air is at 95 kPa and 27°C. Accounting for the variation of specific heats with temperature, plot the cycle on P-v and T-s diagrams and then determine:- (a) the temperature after the heat-addition process, (b) the thermal efficiency, and (c) the mean effective pressure.
An air-standard Diesel cycle has a compression ratio of 18.2. Air is at 120F and 14.7 psia at the beginning of the compression process and at 3200 R at the end of the heataddition process. Accounting for the variation of specific heats with temperature, determine (a) the cutoff ratio, (b) the heat rejection per unit mass, and (c) the thermal efficiency.
Air enters the compressor of a gas turbine at 100 kPa and 25°C. pressure ratio 5 and For a maximum temperature of 850°C, the back work rate and thermal efficiency of the Brayton cycle Please specify.
In diesel cycle at the beginning of the compression process, air is 95 kPa and 690 K. The ideal Diesel cycle has a cutoff ratio of 1.3 and the maximum temperature and peak pressure of 2000K and 6000kPa, respectively. Taking into account the variation of specific heats with temperature, determine a)The compression ratio b) rate of heat addition c) the work cycle d) thermal efficiency in %
An air-standard Diesel cycle has a compression ratio of 17 and a cutoff ratio of 2. At the beginning of the compression process, air is at 95 kPa and 27°C. Take c, = 0.716 kJ/kg K, C, = 1.0 kJ/kg K. Determine the: 1. temperature after the heat-addition process. 2. thermal efficiency. 3. mean effective pressure. 4. temperature after compression. 5. pressure after compression
An air-standard Diesel cycle has a compression ratio of 16 and a cutoff ratio of 2. At the beginning of the compression process, air is at 95 kPa and 27°C. Accounting for the variation of specific heats with temperature, determine the mean effective pressure (in kPa). Note: @T = 300K, u = 214.07kJ/kg, v = 621.2.