1. An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. - Steel A = 500mm2 Aluminum Bronze A = 400mm2 A = 200mm? 40KN 10KN 20KN 1.5m 2.5m 2,5m

1. An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. - Steel A = 500mm2 Aluminum Bronze A = 400mm2 A = 200mm? 40KN 10KN 20KN 1.5m 2.5m 2,5m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A 55-mm-diameter solid circular shaft as shown in the figure is made up of an aluminum material. The...

A: Given; d= 55 mmτ= 75 MPaG = 29 GPaθA/C=0.065 rad

Q: A 12-mm thick steel tire has a width of 110 mm and internal diameter of 800 mm. It is heated and tru...

Q: What is the ratio of the average velocity to maximum velocity for water flowing in a 1” schedule 40 ...

A: The ratio of average velocity to maximum Velocity is to be identified for laminar flow of water thr...

Q: e dynamic and kinematic viscosities of wate

A: Given:Temperature of water, T=327 K

Q: A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional...

A: By steadly flow energy equation : h1+ V^2 /2 +g Z1+q = h2 + v^2/2+gZ2 +W Nozzle is given :- W= 0 ( n...

Q: Consider the thin plate in the form of an equilateral triangle. At the instant shown, point A has an...

Q: The maximum radial load it can sustain

A: Given; The dynamic laod capacity of 6306 bearing Load=20kNThe maximum radial load?Rotation=650 rev/m...

Q: 4. Exams in the LTO are given as a true or false type. If there are 10 questions given, in how many ...

A: As the exams are given only as true or false. the questions can be answered only in two ways either ...

Q: Find the time required for one full cut on a work piece of 350mm long and 20 mm in diameter. The cu...

Q: An orificemeter with orifice diameter 10 cm is inserted in a pipe of 20 cm diameter. The pressure ga...

A: To Find: Discharge of water through pipe, Q Given that, d0=10 cm=0.1 m(orifice),d1=20 cm=0.2 m (pipe...

Q: 3. Find the reactions at the supports A and B for the beam given below. The length of the beam is 12...

Q: By applying a force F, a saline solution is ejected from the 10-mm-diameter syringe through a 0.4-mm...

Q: 4.123 A rigid, insulated tank having a volume of 40 ft° initially contains a two-phase liquid-vapor ...

Q: Explain the "burst potatoes in the boiling water" with thermodynamic viewpoint.

A: Whenever potatoes are boiled in the water, there is heat transfer from the hot water to the potato. ...

Q: The cross-sectional area of each member of the truss is 42 cm. B D 6m 100 kN 300 kN Determine the fo...

Q: 8 F-5 Fighter airplane has q caing area of 170 ft?. The wing gener ateo a lift of 18000 16. For 9 Bl...

Q: Dwing composition on a mole basis: 60% N2 and = analysis of the mixture, and its gas constant.

Q: A uniform bar of length equal to 6 m and weighing 225 N has its one end resting on a rough horizonta...

Q: .........TheGaugePressure 0f the air in an aut0m0bile tire is 25psi, and assuming the ambient atm0sp...

Q: give at least five (5) units of strength of materials based on International System and five (5) uni...

A: units of strength of materials based on International System and units of strength of materials bas...

Q: All dimensions, applied loads P and reactions at A and I are known. Determine the following statemen...

A: It is required to choose correct answer

Q: A pump has a brake horsepower of 39 hp with an efficiency of 81%. Neglecting frictional losses, calc...

Q: Superheated steam at 7.585 MPa (1100 psia) and 616.3 K (650 F) enters the high-pressure turbine of a...

A: At state 1 : Saturated water and P1=7kPa h1=163.3655 kJ/kg v1=.0010075 m3/kg Wp1=h2-h1=v1∆P h2-163.3...

Q: A flat rectangular plate 1 m wide and 2 m long is immersed in water. The shorter side parallel to wa...

A: Width of the flat rectangular plate, B= 1 m Length of the flat rectangular plate, L= 2 m With horizo...

Q: C3/(c) the moment about point A is: 300 cm A 450 200 N

Q: he hydroelectric facility that has been proposed will consist of a turbine with an efficiency of 89....

A: Given:Efficicnecy of turbine=η=89.2%=0.892vertical depth of 14.8 m below the riverbedHydraulic diame...

Q: added 100 kJ of heat. Compute for the heat transferred, change of internal energy, and change of ent...

A: Need to find heat transferred ,change of internal energy & change of entropy.

Q: 2.4 m D 1.8 m 1.35 m 1.8 m 0.9 m B. a. Which of the following is the most stressed leg(s)? b. If the...

A: Draw the given diagram.

Q: what is a simple closed surface that consists of four or more planes?

A: Simple Closed Surface : A simple closed surface is defined as a surface with exactly one interior,...

Q: 5.19 Consider the piping system shown in the following diagram. The pump operates at 1750 rpm. El 14...

Q: 1. Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine th...

A: Find the maximum permissible value of torque

Q: H.W.. Prove that : 02 1 Oy, +

A: We have to proove:→σ1σyt+σ2σyc=1 where: →σ1 and σ2 are principle stresses→σyt and σyc are the tensil...

Q: . 5.20 Suppose you are designing a parachute with a drag coefficient of 0.5. What cross-sectional ar...

Q: Determine the nodal displacements the forces in each element and the reactions.Use the direct stiffn...

A: GivenE1=30×106PsiE2=15×106PsiA=5in2L2=L1=30in

Q: A pelton wheel is having a mean bucket diameter of 1m and running at 1000 rpm. The net head on pelto...

A: A pelton wheel with a mean bucket diameter of 1 m and a speed of 1000 rpm is known.On the pelton whe...

Q: Find the *value of P (Newtons) such that the moment at A of all the forces shown is 500 N-mm counter...

A: Note that there is an ambiguity in the question, for getting the correct answer , net moment about A...

Q: 19. The surface of a circular dartboard has a small center circle called the bull's eye and 20 pie-s...

Q: acceleration of link 1 ?

A: Given; Relative velocity of link 1 with respect to link 2: V1,2=13 m/sLink 2 rotates at constant sp...

Q: O Summing moments about an axis parallel to x, passing through A Summing moments about an axis paral...

Q: The cross-sectional area of the bar is 5 cm². L. Aluminum Steel Aluminum 80 kN - 70 kN | 20 kN - 30 ...

Q: of Disc check va

A: Stage 1 given; What the destroying and Assemble of stomach valve Also what is capacity of part than ...

Q: 6. A card is drawn from a pack of 52 cards. The card is drawn at random. What is the probability tha...

A: Probability=required /total In a pack of card no.of spade=13 no.of jack=13 Probability ( neither spa...

Q: Is it possible for a heat engine's thermal efficiency engine to reach 100% if all reversibilities ar...

Q: equilibrium mixture of CO₂, CO and O₂ at 3000 K, 5 atm. Determine the composition of equilibrium

Q: stop bleeding of capillary, which better tools material the one has higher thermal conductivity k o...

A: This question is based on the concept of tool material and it's properties.

Q: groove is of wi dth r. mine per unit sliding distance when, W = 0,2 mm, and H = 75 MPa.

A: To given that load (W)=50N Diameter (D)=5mm Width(r)=0.2mm Hardness (H)=...

Q: *Prob. 1.4-6. A portion of the boom of a crane at a construc- tion site is shown in Fig. P1.4-6. The...

Q: The temperature field of a flow in which V = 2yi + xj + tk is given by T(x, y, z) = 20xy°C. Determin...

A: Answer: The rate of change of the temperature of a fluid particle in the flow is 120 ℃/sec.

Q: the critical design load

A: In order to find critical design load we have to equate with reactive force per unit area:so that,Ch...

Q: A 10 m3 oxygen tank is at 15 °C and 800 kPa. The valve is opened, and some oxygen is released until ...

A: Given Data State 1: 10 m3,800 kPa, 15°C State 2: 600 kPa,15°C R = 260 J/kg.°K.

Concept explainers

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.

Question

Kindly answer it and show complete solution

1. An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied
at the positions indicated. Find the stress of each rod in MPa. -
- --
Steel
Aluminum
Bronze
A = 500mm?
A = 400mm2
A = 200mm?
40KN
10KN
20KN
2.5m
2.5m
1.5m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A load of P = 4900 N is acting on member AC. The length of AC is d = 300 mm. The cross-sectional area of AB is 375 mm2 while the cross-sectional area of C is 575 mm2 . Determine the magnitude (in N) of the force acting on rod AB if the compressive stress in the smooth support C is equal to the tensile stress in the rod AB. Round off the final answer to two decimal places.
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.
The boom AC is a 4-in. square steel tube with a wall thickness of 0.30 in. The boom is supported by the 0.65-in .-diameter pin at A, and the 0.45-in .-diameter cable BC. Neglecting the weight of the boom, determine the tensile stress in the cable (in psi) if P = 4490 lb. Round off the final answer to three decimal places.
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the frictionless pulley at D. Find the stress (in psi) in the cable if its diameter is d = 0.51 in and the weight of the bar is 5117 lb. Round off the final answer to three decimal places.
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 1 and rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
A thick cylinder internal diameter 240mm external diameter240mm internal diameter ‘D’ is subject to external pressure of 50MPa. Determinethe diameter ‘D’ if the minimum hoop stress in the cylinder is not to exceed200MPa.
Two solid cylindrical rods support a load of P = 27 kN as shown. Rod 1 has a diameter of 16 mm and the diameter of rod 2 is 12 mm. Ø A. Determine the axial normal stress in Rod 1 (MPa). Ø B. Determine the axial normal stress in Rod 2 in MPa.
Determine the largest weight W in N that can be supported by two wires shown in the figure.The stress in either wire is not to exceed 261 Mpa. The cross-sectional areas of wires AB and ACare 258 mm^2 and 320mm^2 respectively.
Determine the stress at the middle of rod BC in MPa for a given truss structure. If the diameter of rod BC is d=20 mm. P1= 12 kN ; P2= 18 kN ; a=3 (m); b=4 (m)
The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the frictionless pulley at D. Find the stress (in psi) in the cable if its diameter is d = 0.55 in and the weight of the bar is 5391 lb. Round off the final answer to 3 decimal places.
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.002L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of 2L, determine the elongation of the block.