1. An engine operating on the air diesel cycle with k-1.3 has thermal efficiency of 63% and a cut-offratio of 1.9. If the pressure atthe end of isentropic expansion is 2.6 bar and bore & stroke of the engine are 105 mm and 130 mm respectively. Determine The maximum pressure of the cycle • The compression ratio The cut off volume

1. An engine operating on the air diesel cycle with k-1.3 has thermal efficiency of 63% and a cut-offratio of 1.9. If the pressure atthe end of isentropic expansion is 2.6 bar and bore & stroke of the engine are 105 mm and 130 mm respectively. Determine The maximum pressure of the cycle • The compression ratio The cut off volume

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 20RQ: Welded ______sealed compressors are normally used in household refrigerators.

See similar textbooks

Similar questions

In an ideal diesel cycle the pressure and temperature at the beginning of the adiabatic compression are 98.5kN/m squared and 60 degrees c respectively.The maximum pressure attained during the cycle is 4.5MN/m squared and the heat received during the cycle is 580kJ/kg gas.Determine ,for the cycle, (a) the volume ratio of compression (b) the temperature at the end of compression (c) the temperature at the end of heat reception (d)the temperature at the end od adiabatic expansion
In an ideal Otto engine, 350 Btu are added during the constant volume process. During the compression process, the initial volume is 6 cu. ft., the initial pressure is 14 psia and the initial temperature is 110 deg. F. If k = 1.34 and the compression ratio is 8, determine (a) percent clearance; (b) highest temperature; (c) highest pressure; (d) the thermal efficiency; and (e) the mean effective pressure.
Prove that the efficiency of the carnot cycle in terms of compression ratio is derived through e = 1 - [1/(rkk-1)]
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 1950 K. Determine the thermal efficiency of the cycle in %.
A Diesel engine has an inlet temperature and pressure of 16 0C and 96 kPa respectively. The compression ratio is 16:1 while the maximum temperature of the cycle is 1260 0C.Illustrate the cycle with the aid of a P-V-diagram, and determine:(a). The cutoff ratio,(b). The specific heat received and rejected during the cycle,(c). The thermal efficiency of the cycle
answer Part 2,3 and 4 only, thanks. An air-standard Carnot cyclewith a pressure and temperature at the beginning of isothermal expansion of 1.2MPa and 380 oC, respectively. The cycle operates with isothermalexpansion ratio of 6 and adiabatic expansion ratio of 3. If the cycle utilizes0.5 kg/s of air, determine: The heat added The heat rejected The thermal efficiency The mean effective pressure
The initial pressure and temperature of air in an Otto cycle engine during compression are 90 kPa and 12°C. Determine the maximum pressure occurring in the cycle if the initial and final temperature during heat addition process are 350°C and 1250°C, and the compression ratio is 6. Please complete the answer for good feedback.?
A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure& temperature is found to be 14.7psi & 546R. The axial flow compressor provides apressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of airinside the engine is 133 lbm/s. Determine the following:a. T-S diagramb. Pressure & temperature at each statec. Thrust force (lbf)d. Propulsive power developed (BTU/min)e. Propulsive Efficiency
A gas-turbine engine with regeneration operates with two stages of compression and two stages of expansion. The pressure ratio across each stage of the compressor and the turbine is 3.5. The air enters each stage of the compressor at 300 K and each stage of the turbine at 1250 K. The compressor and the turbine efficiencies are 80% and 82%, respectively, and the effectiveness of the regenerator is 74%. Assuming variable specific heats for air; show the process in a T-s diagram; calculate the back work ratio; and determine the thermal efficiency of the cycle.
A steady-flow system operating on the ideal Ericsson cycle can achieve the Carnot efficiency. One of the salient features of this cycle is the isothermal expansion through a heated turbine, as shown in Fig. a. Heat is added to the turbine such that the outlet temperature is equal to the inlet temperature, i.e. T₁=T₂, and the overall pressure ratio for this process is rₚ=P₁/P₂. However, an isothermal expansion through a heated turbine is very difficult to achieve in practical engineering applications. An alternate approach is two use a multi-stage expansion process with reheating. In this approach, the gas expansion process is carried out in multiple stages with reheating in between each stage. Consider the two-stage turbine expansion with reheating shown in Fig. b. The gas enters the first stage of the turbine at state A1, is expanded isentropically to an intermediate pressure Pₐ₂, is reheated at constant pressure to state B1, and is expanded in the second stage isentropically to the…
A steady-flow system operating on the ideal Ericsson cycle can achieve the Carnot efficiency. One of the salient features of this cycle is the isothermal expansion through a heated turbine, as shown in Fig. a. Heat is added to the turbine such that the outlet temperature is equal to the inlet temperature, i.e. T₁=T₂, and the overall pressure ratio for this process is rₚ=P₁/P₂. However, an isothermal expansion through a heated turbine is very difficult to achieve in practical engineering applications. An alternate approach is two use a multi-stage expansion process with reheating. In this approach, the gas expansion process is carried out in multiple stages with reheating in between each stage. Consider the two-stage turbine expansion with reheating shown in Fig. b. The gas enters the first stage of the turbine at state A1, is expanded isentropically to an intermediate pressure Pₐ₂, is reheated at constant pressure to state B1, and is expanded in the second stage isentropically to the…
In an air standard gas turbine cycle, air at 14.5 psia and 70 F is first compressed to 80 psia in a compressor of 82 percent efficiency. The hot air leaving the combustion chamber at 1250 F is expanded back to 14.5 psia in a turbine of 85 percent efficiency. If a regenerator is inserted into the cycle to heat the air leaving the compressor to 650 F. (a) determine the thermal efficiency of the cycle. (b) determine the effectiveness of the regenerator. Show complete solution on a paper.