1. Clear All in the simulation. Add a positive and negative charge as shown in the diagram below. Plot equipotential lines in 10 V increments. Note: For this exercise the potential do not need to be precise; the patterns will still be evident if you are within +/- 0.5 V plot [clear equipotential O V voltage Are the equipotential lines evenly spaced (this would suggest a linear relationship) or exponential?

1. Clear All in the simulation. Add a positive and negative charge as shown in the diagram below. Plot equipotential lines in 10 V increments. Note: For this exercise the potential do not need to be precise; the patterns will still be evident if you are within +/- 0.5 V plot [clear equipotential O V voltage Are the equipotential lines evenly spaced (this would suggest a linear relationship) or exponential?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

H:10) Connect a battery to a solenoidA cylindrical solenoid 40 cm long with a radius of 2 mm has 300 tightly-wound turns of wire uniformly distributed along its length (see the figure). Around the middle of the solenoid is a two-turn rectangular loop 3 cm by 2 cm made of resistive wire having a resistance of 195 ohms. One microsecond after connecting the loose wire to the battery to form a series circuit with the battery and a 20 resistor, what is the magnitude of the current in the rectangular loop and its direction (clockwise or counter-clockwise in the diagram)? (The battery has an emf of 9 V.) ................A clockwise counter clockwise
a rod of semiconducting meterial of length L = 2 m and cross-sectioanal area A=5mm2 lies along the x axis between x=0 and x=L. the meterial obeys Ohm's law, and its resistivity varies along the rod according to p=p0 (1-(x2/L2)) where p0=4,5 * 10-4 ohm*m. the end of the rod at x=0 is at a potential V0= 30 V greater than the end at x = L. a)what is the total resistance, in units of ohm, of the rod ? b)what is the current, in units of miliamperes in the rod? c)what is the electric potential, in units of Volt in the rod at x=L/2 ? d)what is the electric field magnitude E, in units of V/m, in the rod at x=L/2 ?
Since there is a charge density of 100 nc / m on the 2 m radius quadrant in the second region, the differential charge taken from a random point and the corresponding ground vector have been correctly defined. Define additionally the location (R) of the point whose potential is desired to be found and the amount of differential change dV in the voltage that will occur due to the differential load you selected. A. R'=2ar ;dq=10-83dφ'dr'; R=zaz ;dv=9109dq/(9+z2)0.5 B. R'=r'ar ;dq=10-8r'dφ'; R=zaz ;dv=9109dq/(9+z2)0.5 C. R'=r'ar ;dq=10-8r'dφ'; R=zaz ;dv=270dφ';/(9+z2)0.5 D. R'=2ar ;dq=10-73dφ'; R=zaz ;dv=9109dq/(9+z2)1.5 E. NONE
7. What can you conclude about the sum of potential differences in a circuit loop? 8. What is the current in the loop? ____A?
Based on the definition of ∆V and current density J⃗ = σE⃗ , discuss the consequence of having a pinched wire running current to some device like the light in the last problem. (By pinched, expect that the cross section is decreased at one spot.)
Discussions:Voltage Distribution and String Efficiency of a Model Suspension Insulator 1- Comment on the results obtained.2- Give reasons for unequal potential distribution over the string.3- What is the effect of this un equality on the insulators?4- Can value of the string efficiency being equal to 100%. Explain your answer.5- Outline methods used to equalize the potential across the units.6- Why an insulator is represented as a capacitor C? What are the assumptionmodes?
4- Can value of the string efficiency being equal to 100%. Explain your answer.5- Outline methods used to equalize the potential across the units.6- Why an insulator is represented as a capacitor C? What are the assumptionmodes?
A 30-volt electromotive force is applied to an ??-series circuit in which the inductance is 0.1 henry and the resistance is 50 ohms. Find the current ?(?) if ?(0) = 0. Determine the current as ? → ∞.
A current I is uniformly distributed over a wire of circular cross section, with radius a as shown is the figure. Find the volume current density.. Answer follow image. Don,t copy from anywhere.Show all calculation and all step.
5. What can you say about the currents? 6. Write an equation for the currents that pass thru point a?
task 2 A. The average surface temperature on Mars is -63 °C, so temperature control is used to drive a heatingelement, or a heater, inside the Martian home. You decided to use an electric heater placed in the middle of the home as your heat source. To measure the temperature, you decided to put athermocouple above the door entrance:1. In order to guarantee that the Martian people will live, you decided to make a closed-loopcontrol system. Based on the exact scenario given, clarify the following:a. Which part resembles the feedback path.b. What is the set value.c. What are the controlling and the controlled variables.d. When you build the Martian dome for the first time, the temperature is -63 C, calculate the absolute error.e. If your thermo-couple measures the values from is -200 to 1500,calculate the error as a percentage. 2. Consider the case when an astronaut comes from the Martian surface into the home.Temperature is expected to drop due to the exposure to the Martian cold wind.…
A. Now suppose the switches are both changed to position B, such that the capacitors and the identical light bulbs are connected. Which light bulb will turn off first? Explain.Hint: consider that the resistances of LB1 and LB2 are identical. B. How much charge will each of the capacitors have in the end?