Question

Hi, can you please help me with all these questions.

Thank you

1. Convert binary number 1011101 to a decimal number.
Expand
Transcribed Image Text

1. Convert binary number 1011101 to a decimal number.

Expert Answer

1 Rating

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Electrical Engineering

Digital Electronics

Related Electrical Engineering Q&A

Find answers to questions asked by students like you.

Q: V:19)

A: Given values are - Ampere hour rating=100AhRest voltageSOCE=11.5VoltDischarge rate=C5Load voltageVL=...

Q: If 50 Hz input ac signal is applied at the input of a half wave rectifier, then what will be the out...

A: Given, 50 Hz input ac signal is applied at the input of a half wave rectifier. Waveform of Half wave...

Q: Answer the following questions: i. If a 3-input XOR gate has eight input possibilities, how many of ...

A: (i) 3 input X-OR gate symbol present as, Where output, w=x⊕y⊕z  

Q: a 220-v dc motor is running at a full load speed of 800 rpm and draws 100 A. calculate at what speed...

A:   We’ll answer the first question since the exact one wasn’t specified. Please submit a new question...

Q: a continuous time signal x(t) = cos(400*pi*t) is sampled at Ts = 1/300s. a) draw the continuous time...

A: As per our policy, i have attempted 3 parts. Given  xt=cos400πtω0=400πTs=1300s a) Calculating x(n) x...

Q: What should be the minimum forward voltage applied to a silicon diode to get significant amount of c...

A: In this case, the minimum amount of forward voltage which must be applied to a silicon pn junction d...

Q: With the transfer functions given below: (a) Find the functions maximum overshoot, Mp (b) Find the f...

A: We are authorized to answer three subparts at a time, since you have not mentioned which one you are...

Q: 1. Compare the output waveform for Half-Wave Rectifier with and without capacitor. Compare the outp...

A: Note:  As per our honor code, we are authorized to answer only one question at the moment. If you wa...

Q: R1 is connected in series with R2 and R3. R2 and R3 are in parallel. what is the value of current fl...

A: For this problem, we have to use two formulas. One is ohms law  I=V/R, another one is current divisi...

Q: 3.8 Use a Y-to-A transformation to find the voltage v in the circuit shown. Answer: 35 V. 28 N 20 Ω ...

A: Click to see the answer

Q: M:09)

A: Click to see the answer

Q: In the circuit given below, R = 70 Ω. Calculate v1 and v2.    The value of v1 in the circuit is ____...

A: Click to see the answer

Q: Consider the circuit shown in Figure 1. Vcc= +12 V (DC), R1 = 100KΩ, R2 = 10 KΩ, RE = 1KΩ and RL = 2...

A: To find all the circuit parameters given the circuit can be modified as From the figure we have 

Q: In a welding process, a current of 400 A flows through the arc when the voltage is 35 V. The length ...

A: Click to see the answer

Q: The network in the Figure below operates at 60 Hz. Compute the energy stored in the mutually coupled...

A: Click to see the answer

Q: consider the periodic function defined over one wavelength by  f(x) = sinkx  (0 <kx < pi)     ...

A: Click to see the answer

Q: Find the value of C (in uF in the network in the figure below such that the total load has a power f...

A: According to question: Load rating in MW is calculated as PL=SL×pf⇒PL=20×0.707⇒PL=14.14MW Now power ...

Q: Vdd value is 12V. Figure 1 Problem 2: Determine the following for the network of figure 2 given that...

A: Click to see the answer

Q: This question from Measurements instrumentation course

A: Non linearity is define as the time or situation at which particular device or element does not meet...

Q: Give output function, transition table and State diagram by analyzing the Sequential circuit shown i...

A: The given circuit is designed using SR flip-flop. First draw the state table for SR flip-flop: S ...

Q: what do you call an equipment that changes the voltage higher or lower without changing the frequenc...

A: =>  Capacitor  bank :- It is used to improve the power factor of the system.  =>  Switchgear :...

Q: Here I attached questions

A: (a) Consider the function is, Q=KL Consider K=2, L=2 Then, the production is, Q=2×2=2 Hence, the out...

Q: 2. Calculate the power delivered (or consumed) by each element in the given circuit. Is the power ba...

A: Click to see the answer

Q: 4.12 Use the mesh-current method to find the power dissipated in the 1 N resistor in the cir- cuit s...

A: Click to see the answer

Q: In the circuit given below, R = 9 Ω. Find the value of i using mesh analysis.     The equation for l...

A: Click to see the answer

Q: In the circuit given below, V = 174 V. The variable resistor is adjusted until it absorbs maximum po...

A: As per maximum power transfer theorem, maximum power absorbed by load resistor if the load resistanc...

Q: For the circuit in Figure 1,  and the 9 V source supplies a current of 7.6 A (that is, a current of ...

A: Here we will apply Nodal analysis to find out the unknown parameters.  => In nodal analysis we co...

Q: Use the node-voltage method to find v in the circuit shown. 4.5 Answer: 8 V. ix 2.5 N 1Ω 4.8 A(1) 37...

A: To find the node voltage v

Q: In the figure, SCR semiconductor switched rectifier to a 220 Vrms ac source at 50 Hz, at load Vdc = ...

A: we have to find (a) the total power absorbed by the load. (b) If the inductance value is 30 mH, the ...

Q: This question from Measurements Instrumetation course

A: Given: Rθ=αeβθ At  θ1=273.15 K,   R1=9 kΩθ2=373.15 K,   R2=0.5 kΩ  

Q: Explain the principle behind SP log and gamma ray log?

A: Click to see the answer

Q: The depletion region consists of (a) nothing but minority carriers (b) positive and negative ions

A: The depletion region exists on both sides of the junction and it covers some area near the junction ...

Q: Transmission and Distribution of Electric Power Answer the Following Question Please: Q) Three-phase...

A: Click to see the answer

Q: Please answer the following, what identifies a circuit as a diode digital logic AND gate? as a diode...

A: 1. Diode digital logic AND gate The logic circuit of AND gate will be Truth table A B D1 D2 Y ...