1. Design a Hydraulic circuit for the excavator earth moving equipment used in construction sites.

Q: I Review Part A- Transmitted power Learning Goal: To determine the maximum possible power…

A:

Q: Suppose that you have designed a portable compressed-air supply system, as shown in the figure…

A: Given: To find: Fault tree

Q: n ammonia compressor has a clearance of 5 percent and a pressure ratio of 5. determine. volumetric…

A: To determine the volumetric efficiency of the compressor.

Q: Explain in detail the commonly used logic functions in Electro-Hydraulics

A: Following are the different types of logic function are- AND Logic - In this logic function the…

Q: Draw the diagram of float sensor and bellows and capsules explain its operation in detai

A:

Q: . What is the energy stored in the spring if the spring iscompressed 0.5 m?

A: Given data mass = 40 kgspring constant = 3000 N/mCompressed length = 0.5 mWe have to find the energy…

Q: la) If a 35 tonne block is raised to 110m and then falls to ground level (in generating mode) in 3…

A: 1a) Given         Mass, m = 35 ton = 31751 kg       Height, h = 110 m          Time, t = 3 min…

Q: State the common dimensional units for the input and output of generator of electricity.

A: Concept: 1) Generator is a machine which converts mechanical energy into electric energy.  2) Input…

Q: (a) Complete the given hydraulic schematic diagram in Figure 2 for meter-in circuit. litar…

A:

Q: The hydraulic system is Less precise than open system O Both hydraulic and pneumatic systems are…

A: Hydraulic system: It is a energy transfer technology from one place to another place by using fluid.…

Q: A water motor is supplied from horizontal 30cm pipe and uses 220liters/s, Discharge take place…

A:

Q: The pendulum of a wall clock has a time period of 2 seconds. Thus, the 'effective length' of a…

A:

Q: 20kym 30KN/m Fi GOKN Sonw Find Fi, f, and f3 To stóbilize the system

A: For UVL; point load = 45 KN at 2 m from the left-hand side. For UDL; point load = 40 KN at 6 m from…

Q: External Force Damper mass m Smooth Surface No Friction Spring eMechanica.com

A: Given data, From the Dalembert's principle the equation of motion can be given as –

Q: 1- Advantage & disadvantage fiber optics. 2- RAM&ROM 3- ADC&DAC

A: Correspondence through optical fibre cable may be seen of as a method of delivering light pulses…

Q: Example 8.8 Figure 8.11 shows the arrangement of differential bellows to measure absolute pressure.…

A: Given Data: ∆P = 12kN/mm2 = 12 x 103 N/mm2A = 1000 mm2Ks = 3 N/mmKb = 1 N/mm→change in pressure ∆P…

Q: A pipe with a 2 m diameter carries water having a velocity of 4 m/s. What is the discharge in cubic…

A: Given      Diameter, d = 2 m        Velocity, v = 4 m/s Find   Discharge, Q

Q: 1) The pendulum, in a wall clock, is a "seconds pendulum", i.e. it has a time period of 2 seconds.…

A:

Q: Exercise: 1. Design a hydraulic circuit to operate the shear as in part B as well as ensuring that…

A: A shuttle valve, also known as a double-check valve, allows pressure in a line to be obtained from…

Q: Explain the following terminologies in Simple Harmonic Motion (SHM)-Amplitude, Frequency, and…

A: The amplitude is essentially the maximum displacement of the object from the harmony position. So,…

Q: An LSA is needed to deliver a pulling force of 60 Newtons as part of a larger machine. The…

A:

Q: Illustrate the comparison between Electro-Pneumatic and Electro-Hydraulic Power system with…

A: A hydraulic power system is used the fluid pressure to transmit power. This system carries a high…

Q: Benzene flows through a 100 mm diameter pipe at a mean velocity of 3 m/s. Find discharge in liter…

A: Find the discharge in liter/sec.

Q: 3/ Design the hydraulic circuit for any one hydraulic system application with working and neat…

A:

Q: 1. Compare and contrast between hydraulic, pneumatic and electro mechanical power system

A:

Q: State the various components of any hydraulic circuits. Give details of each component with its use…

A: Components of hydraulic system::: the various components of a typical hydraulic system. A fluid…

Q: a. Explain how the output power of a turbine-generator operating in a constant frequency system is…

A: Isochronous Operation Examples Consider an islanding electrical power system with one…

Q: P:- Solve the System of Linear algebroie EXuation G.E-H. X- y +7-2 W = -1 - 2K+2y-7+2w = 3 3X -3y…

A:

Q: Through appropriate sketching, determine the types of grippers or tools, which is most suitable for…

A: 1) Vacuum Grippers Compacted air-type grippers produce somewhere in the range of four and multiple…

Q: 15. If a hydraulic motor with a displacement of 1.65 in./rev receives fluid at 20 gal/min, what…

A: Soln :- displacement = 1.65 in^3/rev. Q =20 gal/min As we know Q = displacement × N 20 gal/min =…

Q: Problem 6.1 Consider the sinusoidal voltage v(t) = 25 cos(400nt + 60°) V. %3D a.) What is the…

A:

Q: a) Perform the comparison between model for system electrical, mechanical and electromechanical

A: SYSTEM  Systems Engineering is an interdisciplinary discipline of engineering and engineering…

Q: cylinder has to move a certain load through a certain distance in 1 s at a pressure of 140 bar. An…

A: Given data as per questionHydraulic cylinder move a certain load to distance in 1 s at  pressure=140…

Q: 1. Describe the circumstances that would make the impounding of a reservoir across a stream…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 2- Figure below provides a pneumatic circuit diagram for a pneumatic system. Obtain the step diagram…

A: Signal 1.2:  This is the start signal. Signal 1.3:  Limit Switch for 2nd Cylinder Extended Position.…

Q: L Reviev Learning Goal: To determine the angle of twist for a circular shaft that is composed of…

A: Solution - Given data - P =220.0 hp              ω =1800 rpma =7.750 in               b=12.00inc…

Q: Derive this equation of cables under distributed loads

A:

Q: 1.5 m/s 1.5 m/s 1.5 m/s 1.5 m/s 2) A 7.5 m/s 6 m'/s C 4.5 m'/s 3 m/s -10 m *10 m 10 m 10 m- A.C.…

A:

Q: Vertical configuration for hydraulic power units are usually used for applications which require…

A: The given statement is True.

Q: 4.19. An arrow leaves a bow at 25 m/s. (a) What is its maximum range? (b) At what two angles can it…

A: We are suppose to solve only one question. Please post other question as a separate question. Given…

Q: A 80-mm diameter plunger is being pushed at 14 mm/sec into a tank filled with oil having sp. gr. of…

A: The oil that is being forced out is 0.3383 N/s.

Q: For the clamping network, the magnitude of must be chosen to ensure that the voltage across the…

A: Option a is correct.

Q: Write the SI units of linear impulse.

A: Given Data> Linear impulse

Q: Q1) Consider the type one servo system given by:

A: To determine controllability & observability of the system

Q: If a spring has solid length of 10 cm, maximum compression deflection of 1 cm and clearance between…

A: Given Data⇒ Compression spring Solid length=10 cm Compression deflection=1 cm Clearance between…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.