The heights is on the second picture. 40N150KN4m4mBmSmC.II 1. Determine the force in bars BD, CD, and DE of the nacelle truss shown in the figure belowby method of joints. (check it for method of section) provide 2 solutions. Answer will be 2decimal point.150KN120시150 시4e7m4m

Answered: Image /qna-images/answer/4ce66467-0a03-4179-90df-a5b8d6bfc422.jpg

Answered: 1. Determine the force in bars BD, CD,…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
36 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, By=? a) 0B) 48C) 24D) NoneE) 14
The length of the 3/32 in.diameter steel wire CD has been adjusted so that with no load applied, a gap of 1/16 in. exists between the end B of the rigid beam ACB and a contact point E. Knowing that E=29 X 10⁶ psi, determine where a 50-lb block should be placed on the beam in order to cause contact between B and E.
Determine for in the member AD And BC using method of joints. (Theta=30 degree)
.15 2.16 The three forces acting on the beam can be replaced with a single equivalent force R. Determine the angle θ and R. 25kN P2 60 kN P3 80 kN 40° 50° 4 m 6 Figure P2.16 COMPANY
The bent bar shown is subjected to 3 forces shown. Replace these forces with an equivalent couple M and single force F at point A. Show solution to answers M = 21.8 kN-m, cw Fv = 12.03 kN, D FH = 1.60 kN, R
31 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, the shear force at point E T=? a) 2B) 4C) 14D) 0E) 6
Q2 Fos the bearn shown: (a) Use the stiffness method to determine all fhe resctions at supports, (b) Dras the quantitative free-body diagram of member, (€ Draw the quantitative shear diageam, bending moment disgram and qualitative deflected shape. Take J = 200(10°) mar and £ = 200 GPa.and suppon & settlement 10 mm a £ 14, - 10 &m dm dm
The electric power transmission tower supports two wires that apply 18 kN verticalforces, and the 36 kN horizontal force crudely models wind loading during astorm. Use the method of sections to determine the force in members IF, IM andBD.
W=1317 kN/mUsing Three Moment Equation, determine all reactions at supports also, determine shear andbending moments with complete labels. Use 1= 1/12 bh^3 and E = 2.15x10^7 KPa
(G) Using these results (δ1=0.1097 in. , δ2=0.1265 in. , δ3=0.0548 in.) determine the deflections of Joint B and Point D. ANSWERS in inch (H) On a piece of paper, sketch a free body diagram (FBD) cut through rod (3) and also a FBD of the rigid bar. Using these, find a relationship between the force in rod 1 (F1) and the applied load, P, a relationship between the force in rod 2 (F2) and the applied load, P, and also a relationship between the force in rod 3 (F3) and the applied load, P. (I) Based on the allowable stress for the bronze, calculate the maximum allowable force that can be supported by rod (1), and the corresponding maximum value for the applied load P. IN KIPS (J) Based on the allowable stress for the aluminum, calculate the maximum allowable force that can be supported by rod (2) and rod 3, and the corresponding maximum value for the applied load P. IN KIPS (K) Using the results from Part 8, determine the deflections of Joint B and Point D. IN INCH NOTE: These are the…

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

1. Determine the force in bars BD, CD, and DE of the nacelle truss shown in the figure below by method of joints. (check it for method of section) provide 2 solutions. Answer will be 2 decimal point. 150KN 120시 15o 시 4