1. Determine the internal stresses developed in bars JH and HY when bar JH experiences a change in temperature of -250•C. Bar JH is made of aluminum, while bar HY is made of steel. Both bars have the same cross-sectional area. Note: Pin H is connected to a wheel that is restricted to move along the inclined slope. 450 H 1 m 250 Y 2 m Material a (/ °C) E (GPa) Steel 11.9 x 10-6 200 Aluminum 22.5 x 106 70

1. Determine the internal stresses developed in bars JH and HY when bar JH experiences a change in temperature of -250•C. Bar JH is made of aluminum, while bar HY is made of steel. Both bars have the same cross-sectional area. Note: Pin H is connected to a wheel that is restricted to move along the inclined slope. 450 H 1 m 250 Y 2 m Material a (/ °C) E (GPa) Steel 11.9 x 10-6 200 Aluminum 22.5 x 106 70

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.27P: -27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile...

See similar textbooks

Similar questions

-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A hollow metal tube with an inside diameter of 145 centimeters must carry a tensile load of 670 kilo newton. Determine the outside diameter of the tube, in meters, if the stress is limited to147 Mpa.
mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
41.) A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa. Towhat value may the internal pressure be increased if the stress in the steelis limited to 100 MPa?
A steel pipe 1.5m in diameter is required to carry an internal pressure of 750 KPa. If the allowable tensile stress of steel is 140 MPa, determine the required thickness of the pipe in mm.
A thick cylinder internal diameter 240mm external diameter240mm internal diameter ‘D’ is subject to external pressure of 50MPa. Determinethe diameter ‘D’ if the minimum hoop stress in the cylinder is not to exceed200MPa.
1. A circular cylinder with inside diameter of 10 cm which carries a compressive force equivalent to 400,000 N. What will be the outisde diameter of this cylinder if the allowable stress is 120 megaPascal. 2. Maximum M occurs when the _______________ is ______________.
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
1.A cylindrical pressure vessel is 500 mm in diameter and has a wall thickness of 22 mm. If it is subjected to an internal pressure of 5 MPa, determine the tangential and longitudinal stresses developed in the cylinder.