Plz 1 , 2 and 3 Part (2): Assume a crankshaft is at determined instantons angle and positions as shown Figure.4,200 mm50 mm300 RPM450Figure.4: Instantons positions of piston in crankshaft mechanismBy make use of trigonometric methodology, you are requiredfind the following parameters of the planarmechanisms:1. Find the tangential velocity (VA)o2. Construct diagrams to show, the rotational motion (tangential velocity vector OA) of link OA,combined rotational and translational motions (relative tangential velocity AB) of link AB, and thepure translational motion of Piston B.3. On the previous velocity vector diagram, use sine and cosine rules to find the necessary angels andvector magnitudes.Find the tangential velocity (Vn and then find the angular velocity of link AB, awAB5. Find the translation velocity of the piston, (VB)o4.

1. Find the tangential velocity (VA)o 2. Construct diagrams to show, the rotational motion (tangential velocity vector OA) of IIAK combined rotational and translational motions (relative tangential velocity AB) of link AB, and the pure translational motion of Piston B. 3. On the previous velocity vector diagram, use sine and cosine rules to find the necessary angels and

1. Find the tangential velocity (VA)o 2. Construct diagrams to show, the rotational motion (tangential velocity vector OA) of IIAK combined rotational and translational motions (relative tangential velocity AB) of link AB, and the pure translational motion of Piston B. 3. On the previous velocity vector diagram, use sine and cosine rules to find the necessary angels and

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the manipulator linear and angular velocity for the 3-DOF articulated armusing Jacobian modelling
A mono-cylinder engine has r = 0.3 m, l = 0.9 m, It has: crank mass m2 = 4.5 kg , crank rG2 = 0.4r, conrod mass m3 = 12 kg ,conrod rG3 = 0.3l from A, and piston m4 = 5 kg. The crank is rotating at constant speed ω =3000 rpm. The following equation is an approximation of the gas force over 180° of crank angle with Fgmax = 3000 N and β = 15º. we need to find the gas force, gas torque, and inertia force . Use approximate expressions in your calculation
Kinematics question. Solve using Instantaneous centre of Velocity.
problem 15.75 this is a dynamics problem
Specifically a dynamics problem. Question in pic below. Answer: omega = 3.75 rad/s
an airplane turbofan compressor blade is 3.0 m long and is rotating at 12350 rmp. Calculate the following- angular speed, w_____________rad/s linear spped at the tip of the blade, v=_________m/s angular and linear displacement after 3.3s, 0= ___________rad s______________m
Crank 2 of the push-link mechanism shown in the figure is driven at w2=60 rad/s cw. Find the velocities of point B and C.|AO2|=150 mm, |BA|=800 mm, |O4O2|= 75 mm, |BO4|= 300 mm, |DA|=150 mm, |CD|=100 mm. (Using Complex Algebraic approach do the Position Analysis; Velocity Analysis and Acceleration Analysis then solve the problem please)
Using the image on the Moment of Inertia Tab, where the following criteria are considered:Assign the values to “Apply torque” = 2 Nm, “Brake force” fr = 0.2 N. “Platform Mass” m= 0.25 kg.Use"radians" for angle units. Write down the values that appear in the graphs of torque, a moment of inertia, and angular acceleration. Then, obtain the other physical quantities by applying the equations of rotational dynamics that correspond to:Time:4.5Applied torque:2 N-mBrake torque:Net torque:Angular impulse:Moment of inertia:Angular acceleration:Initial angular velocity:Final angular velocity:
Please include explanation. A 6-MW offshore wind turbine has a capacity factor of 40%. It has a height of 120 m, and 107-m long blades. The angular acceleration is 1.388 rad/s2. Assume that the distance from the center of the turbine to the connection with the blade is negligible, and that the turbine starts from rest. At ? = 12 s, calculate the velocity and the acceleration for points (a) at half the length and (b) at the tip of the blade.
Solve the dynamics problem asap
mt 8-A) For the adjacent figure: a) Develop the exact and linearized equation of motion by either Newtons Method or Lagrange
Problem 15.72 2 images This is a dynamics problem concerning motion