1. For surface grinding a 2 x 3 inch surface using 1 in thick disc. What is the time required to finished a cut when the depth of cut is 0.01 inch and the feed rate 0.05 inch/rev, RPM is 60.

Q: At 27 °C the reading on a manometer filled * with mercury is 90.6 cm. To what pressure does this…

A: The density of mercury at 27 degrees celsius is nearly 13.5*1000 kg/m3.

Q: A system contains water at temperature T = 700 °C, and specific enthalpy h=3462.15 kJ/kg. Determine…

A: Given data, Water is the working fluid T = 700°C = 973.15 K h = 3462.15 kJ/kg Find specific entropy…

Q: What would be the lead of a ¾ inch diameter drill with an include angle of 118 degrees

A:

Q: The angular velocity of the disk is defined by w = (5t2 + 2) rad/s, where t is in seconds.…

A:

Q: The arm that joins gears A and B rotates anti-clockwise with 24 rad/s. At the same time, gear A…

A:

Q: The velocity distribution within the fluid flowing over plate is given by (u-3/4 Y-Y 2) as shown in…

A:

Q: For the given cross-section, if the width b = 6.6 in., the height h = 8.4 in., and the internal…

A:

Q: The resultant loading force is 2.5 kN/m 3 m KN. 0.5 kN/m B 1 m 1.5 kN

A: The resultant loading force: R = 6 kN

Q: A 15 mm diameter cylindrical nuclear fuel rod is housed in a hollow ceramic cylinder concentric to…

A: Given   Radius, r1 = 7.5 mm                r2 = 17.5 mm                r3 = 55 mm Heat transfer…

Q: Read the question carefully before answering. Show complete solution with proper derivatives /…

A:

Q: An Otto cycle has an initial temperature of 27oC and 102 Kpa air. The compression ratio is 10 and…

A:

Q: The pressure................. the depth of .the liquid increases Decreases. O Increases. O O None…

A:

Q: Joul In English unit Ft Ihf

A: Given convert Joule to britsh/english unit

Q: A certain SSSF turbine (irreversible and adiabatic) operates on air with the following conditions,…

A:

Q: Sind y at 2 m from the left hand 7111 سحله ولي dx

A: Concept: The integration of the load intensity is the shear force. The integration of the shear…

Q: There are two turbine stages with a reheater in between, as shown below and the following conditions…

A: Given:P1=1200 KPa T1=1200 KP2=350 KPaP3=350 KPaT3=1200 KP4=100 KPa

Q: There are two carnot engines A and B operating in two different temperature regions. For engine A…

A: Given data: Reservoir temperatures of Engine A : 150°C and 100°C Reservoir temperatures of Engine B…

Q: 2. Dip-coating process is one of the methods for electrode surface modification.

A: given; dip-coating process is the one of the method for electrode surface modification.

Q: A single square thread power screw is to raise a load of 70kN. The screw has a major diameter of…

A:

Q: Figure 1 shows a simple system to lift a heavy load. The dimensions a = 3.6 m and b = 1.2 m. The…

A: given : W = 20000 g = 20kg CW = 45000 g = 45 kg

Q: Pressure is expressed as the equivalent height of a fluid column.

A: Given: Let us consider the given statement, "Pressure is expressed as the equivalent height of a…

Q: .Make a checklist of the properties and characteristics of engineering materials that need to…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: Q4: The pump shown in figure (2) adds 25 kW to the water and causes a flow rate of 0.04 m³/s.…

A:

Q: 4. A given beam, of L-3m and El-6000kN.m², is subjected to a uniformly distributed load (w). The…

A: Given

Q: The figure shows truss. It is supported with a pin at A and a roller at B. There are three pointed…

A: (a) Draw the free-body diagram of the truss.

Q: 5. Atwood's Machine. A 15.0-kg load of bricks hangs from one end of a rope that passes over a small,…

A: Given:mass of counterweight=28 Kgmass of bricks=15 Kg

Q: An example of a performance with two phases is the bench press; in the down phase the lifter lowers…

A: The preparation phase and the movement phase of the bench press exercise can be separated.…

Q: Pressure is expressed as the equivalent height of a fluid column. True False

A: Correct answer: True

Q: Two thin-walled aluminum tubes will be used to support a torque and they have same cross- section…

A: Introduction: When a shaft is torqued or twisted, shearing tension is created in the shaft. The…

Q: 0 A (1/5) scale of a vehicle is to be tested, One in a wind tunel, second in a water tunnel,…

A: Given    Length ratio = 5        Speed, vp = 120 km/h Find   Velocity, vm

Q: A. Statics 8. Which of the following A. motion and mass B. Dynamics C. Kinetics property of an…

A:

Q: The Carnot cycle is composed of four reversible processes two isothermal and two adiabatic and it…

A: carnot cycle was developed by physicist Sai carnot. Carnot cycle only exist in ideal case , it…

Q: 158 158 258 350 The crate weight is 270 lb. The minimum force p for tipping is lb

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: Oil at 500K is to be cooled at 5000K in a counter current exchanger using cold water available at…

A:

Q: Is expressed as the equivalent height of a fluid column. None of the these Force Work O Tension…

A: To find :- Correct option

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The…

A:

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given: Let us consider the given data,  d=0.75P=56 kipsn=5 Where, d=Diameter P=Applied load n=Bolt…

Q: A couple is a free vector. O true O false If a system is in equilibrium, the sum of all forces…

A: subject : classical mechanics

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

A: Given data: d=516 inτ=32 ksi Need to determine the maximum allowable load that can apply.

Q: A system contains water at pressure P = 30 kPa and specific entropy, s = 7.6198 kJ/(°K * kg).…

A: Given data, Water is the working fluid P= 30 kPa s = 7.6198 kJ/kg.K Find specific enthalpy = h

Q: Determine the force in members AB and AG. Indicate if the members are in tension or compression -…

A:

Q: Q2: As shown in figure (2), when the pump develops (7.5m) of head, and the velocity of flow through…

A:

Q: A fixed-mass system contains mass, m = 1.0 kg of air. A thermodynamic process occurs from state one…

A: It is very basic question of thermodynamics. Used concept is entropy change of air . Air modeled as…

Q: When the system is completely isolated from its surroundings so that there is no heat transfer, this…

A: Explaining, In which process, when the system is completely isolated from its surroundings there is…

Q: * The height of the free surface above :any point is none as None of the above O Static head. O…

A: Given Statement:-  The height of the free surface above any point is known as:-  Options Available:-…

Q: Question 1 Aluminum rod E = 10400 ksi Allowable axial deformation= 0.3 in. Tension in the rod= 2300…

A:

Q: In the metric engineering system a common unit is the kilojoul force per square centimeter. True O…

A: To find :- True or false

Q: Determine the pressure difference between points A and B in Fig. 21cm 9cm Kerosene Air cm THE 110 cm

A: Assumptions: The specific weight of the fluids is not given. Hence, the following standard values…

Q: If load P = 17.3 kips, determine the normal force in bar (1). A 6 ft O 36.5 kips O 28.8 kips O 17.7…

A:

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.