The arm that joins gears A and B rotates anti-clockwise with 24 rad/s. At the same time, gear A rotates at 4.8 rad/s also anti-clockwise, determine by IC the angular velocity of gear B and speed VB

Q: Given the following translational mechanical system, find the transfer function G(s): -x, (t)…

A:

Q: Q3/B/ List the properties required for heat exchanger. Discuss the heat exchanger i forhaber

A:

Q: Determine the pressure difference between points A and B in Fig. 21cm 9cm Kerosene Air cm THE 110 cm

A: Assumptions: The specific weight of the fluids is not given. Hence, the following standard values…

Q: Liquid flowing at high speed in a wide, horizontal open channel under some conditions can undergo a…

A:

Q: 2) An idealized free-body diagram of a door handle is shown below. To simplify, member X-Y is only…

A: Given: Let us consider the given data, M=1500×0.100=150 NmT=1500×0.2=300 Nmdiameter,d=20 mm=bσ= 3MPa

Q: 7.14 In a 1:40 model of the flow over the crest of a spillway the velocity at a particular point is…

A:

Q: Water flows over a waterfall 328 Ft in height. Take 2.204 lb of the water as the syste and assume…

A: given : h = 328 ft h= 328/3.281 m h = 100m       m = 2.204 lb m= 2.204/2.205 kg m=0.9997 kg

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A: Given:F1=15 kipsF2=34 kipsσallow=21 ksi

Q: The thrust of a shaft is taken by a collar bearing filled with a forced lubrication system which…

A: Given data: thickness, t = 0.3 mm = 0.0003 m Outer diameter of the collar, do = 156 mm = 0.156 m…

Q: The resultant force acting of the uniformly distributed loading dependson the distance between the…

A: Given statement is true

Q: fair is such that the s 310 m/s, a press tunnel is used

A:

Q: For a steel alloy it has been determined that a carburizing heat treatment of 10-hour duration will…

A: given : x1 = 2.5mm x2 = 5mm t1 = 10 hr

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A:

Q: uniform diameter d= 1.75 in. Segment (1) is an aluminum = 10000 ksi L₁ = 90 in. Segment (2) is a…

A: Solution - Given data - d= 1.75 in                       E1 = 10000 ksi    L1 = 90 in…

Q: If the eyebolt is made of a material having a fail stress of o= 180 MPa, determine the minimum…

A:

Q: The angular acceleration of a body which is rotating about a fixed axis is given by a = -kw², where…

A:

Q: Ball B is being suspended by a 1000mm long elastic cord from a wooden ceiling. The ball’s mass is…

A:

Q: A 300 mm x 150 mm venturimeter is provided in a vertical pipeline carrying oil of specific gravity…

A: Venturimeter is a device used for measuring the velocity of flow of fluid through the pipe.…

Q: (b) A block weighing 2000 N is on a rough inclined plane that makes angle of 15° with horizontal.…

A: Given:W=2000 Nθ=15°F=800 N

Q: Determine the magnitude of the resultant force. The magnitude of the Resultant force is nearly O 40"…

A:

Q: When energy in the form of heat is added to a body, it is stored as heat. True

A: When the energy in the from of heat is added to the body, then this energy increases the internal…

Q: Q4(a) Explain laws of static friction.

A:

Q: A manufacturer is carrying out a vehicle performance analysis and subjects to a road test. The…

A:

Q: The key to profitable operation for project cost control is: O O To keep the project cost equal to…

A:

Q: If a block is stationary, the friction will always be f = µN, where is the coefficient of static…

A: If a block is stationary, the friction will always be f=μN, where μ is the coefficient of static…

Q: 5-stage c must be

A: Given: N=5 ρ1=ρs=100kρa T1=200C=293Kn=1.4 isotropic ρd=900kρa W=?QR=?

Q: Q1/ The gauge pressure of the air in the tank shown in (Fig.1) are measured to be 80 kPa. Determine…

A: The differential height of the mercury column: h = 0.582 m

Q: Consider the system shown in figure. Block A weighs 45.0 N and block B weighs 25.0 N. Once block B…

A: Whenever the surfaces of two bodies are in contact there will be limited amount of resistance to…

Q: The losses per unit length pipe^h/l in turbulent flow through small pipe depend upon Velocity,…

A: Introduction: Head loss is the energy wasted in a fluid system due to friction along the length of a…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A:

Q: A ladder AB is leaning against a smooth vertical wall at A and is resting on a horizontal floor at…

A:

Q: stion 2 Determine the force at Joint C (للشكل الموضح احسب القوة في العقدة C) hand written plz B D 30…

A:

Q: P = 15 Kips. Neglect the weight of the beam. The reaction at A Is Kips. A 3 ft - 6 ft- 6 kips B 2 ft…

A: Given data: P = 15 Kips We have to find the reaction at A.

Q: Section A (An Q1(a) Explain types of pin jointed frames with examples.

A: given; explain type of pine joined frames with examples.

Q: Find the eigenvalues and eigenvectors of the matrix -4.0 4.0 A -1.6 1.2

A:

Q: Problem 8.1 Water at 20 °C flows through the pump impeller shown in the figure below, where the…

A:

Q: The input piston and output plunger of a hydraulic car lift are at the same level, as shown in the…

A:

Q: Q2/ In Fig. 2 both the tank and the tube are open to the atmosphere. If L = 2.13 m, what is the…

A:

Q: A spherical gas-storage tank with an inside diameter of 32 ft is being constructed to store gas…

A:

Q: pastai Problems 10-16 Information: Jose' pushes a wheelbarrow consisting of a wheel (mass mw = 3 kg,…

A:

Q: A vertical rectangular plane surface is submerged in water such that its top and bottom surfaces are…

A:

Q: Show in Figure 1 is the water flow system. The velocity head difference is .  Volume flow rate is .…

A:

Q: If the body is lowered against a resisting force equal to its weight, the work done by the body is…

A: Concept: 1) Consider a body of weight 'W'.  2) Resistant force is F.  3) Given that , W=F. And also…

Q: jack screw

A: For screw(Cast iron)d=2.5 inTPI=2.25μt=.15For collardi=1.5 indo=3 inμc=.25W=2 tons Pitch of screw in…

Q: Thermodynamics that takes place at a constant temperature is called Heat Capacity Enthalpy…

A: Given data To select the correct option.

Q: estion 2 Determine the force at Joint C (للشكل الموضح احسب القوة في العقدة C) hand written plz -m B…

A:

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: Given:P=395 NL=700 mmd=42 mm

Q: 7. Calculate the minimum radius of curvature in the steady turn for a single-engined jet aircraft,…

A: Write the expression of minimum radius of curvature in the steady turn for a single-engined jet…

Q: What is the difference between mobility and mobility ratio in enhanced oil recovery.

A: Given question : What is the difference between mobility and mobility ratio in enhanced oil…

Q: : Aluminum rod stock with a starting diameter = 0.50 in is drawn through a draw die with an entrance…

A: Given data: Initial Diameter, Di = 0.5 in final diameter, Df = 0.15 in angle, A = 13 degrees…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.