1). For the following aqueous solution, please arrange the expected solubility CuBr from lowest to the highest solubility? A). water B). 0.010 M AgNO3 D). 0.04 M CUNO3 C). 0.01 M CaBr2 E). 0.01 M Ca(NO3)2

Some barium chloride is added to a solution that contains both K2SO4 (0.050 M) and Na3PO4 (0.020 M). (a) Which begins to precipitate first: the barium sulfate or the barium phosphate? (b) The concentration of the first anion species to precipitate, either the sulfate or phosphate, decreases as the precipitate forms. What is the concentration of the first species when the second begins to precipitate?

Calculate the solubility (in grams per liter) of magnesium hydroxide in the following. (a) pure water (b) 0.041 M Ba(OH)2 (c) 0.0050 M MgCl2

A solution contains 0.00740 M calcium ion. A concentrated sodium fluoride solution is added dropwise to precipitate calcium fluoride (assume no volume change). a At what concentration of F does precipitate start to form? b When [F] = 9.5 104 M, what is the calcium-ion concentration? What percentage of the calcium ion has precipitated?

. Under what circumstances can we compare the solubilities of two salts by directly comparing the values of their solubility products?

. The solubility product of iron(III) hydroxide is very small: Ksp=41038at 25 °C. A classical method of analysis for unknown samples containing iron is to add NaOH or NH3. This precipitates Fe(OH)3, which can then be filtered and weighed. To demonstrate that the concentration of iron remaining in solution in such a sample is very small, calculate the solubility of Fe(OH)3in moles per liter and in grams per liter.

Which of the following will affect the total amount of solute that can dissolve in a given amount of solvent? a. The solution is stirred. b. The solute is ground to fine particles before dissolving. c. The temperature changes.

How would the solubility of calcium fluoride be affected by the presence of fluoride ion from another source? What is the solubility of calcium fluoride in a saturated solution of barium fluoride? How does this compare with the value of the solubility of calcium fluoride found in Example 17.4? Is this what you expect?

Solubility and Solubility Product You put 0.10-mol samples of KNO3, (NH4)2S, K2S, MnS, AgCl, and BaSO4 into separate flasks and add 1.0 L of water to each one. Then you stir the solutions for 5 minutes at room temperature. Assume that you have 1.0 L of solution in each case. a Are there any beakers where you would observe solid still present? How do you know? b Can you calculate the potassium ion concentration, K+, for the solutions of KNO3 and K2S? If so, do the calculations, and then compare these K+ concentrations. c For the solutions of (NH4)2S, K2S, and MnS, how do the concentrations of sulfide ion, S2, compare? (You dont need to calculate an answer at this point; just provide a rough comparison.) Be sure to justify your answer. d Are there any cases where you need more information to calculate the sulfide-ion concentration for the solutions of (NH4)2S, K2S, and MnS from part c? If so, what additional information do you need? e Consider all of the solutions listed at the beginning of this problem. For which ones do you need more information than is given in the question to determine the concentrations of the ions present? Where can you find this information? f How is the solubility of an ionic compound related to the concentrations of the ions of the dissolved compound in solution?

To a beaker with 500 mL of water are added 95 mg of Ba(NO3)2, 95 mg of Ca(NO3)2, and 100.0 mg of Na2CO3. After equilibrium is established, will there be • no precipitate? • a precipitate of BaCO3 only? • a precipitate of CaCO3 only? • a precipitate of both CaCO3 and BaCO3? Assume that the volume of the solution is still 500.0 mL after the addition of the salts.