1. For the given converter shown in Fig. 1, Vg = 20V, L= 10 mH, C = 10 uF, R = 102, D = 0.5. %3D %3| D; 7. Figurel A. Assume that thediodw and the switch have a voltage drop of V Don and VTon during the conduction, respectively. Determine the voltage conversion ratio as function of VDon and VTon and D. B. Assume that VDon = 1V, and VTon =1V, plot the voltage and current of each device, for example switch, diode, inductor, and capacitor in steady state. Determine A¡, and Ar and include them on the graph show the magnitude and time information. C. Determine the efficiency of the converter under the condition of part B.

1. For the given converter shown in Fig. 1, Vg = 20V, L= 10 mH, C = 10 uF, R = 102, D = 0.5. %3D %3| D; 7. Figurel A. Assume that thediodw and the switch have a voltage drop of V Don and VTon during the conduction, respectively. Determine the voltage conversion ratio as function of VDon and VTon and D. B. Assume that VDon = 1V, and VTon =1V, plot the voltage and current of each device, for example switch, diode, inductor, and capacitor in steady state. Determine A¡, and Ar and include them on the graph show the magnitude and time information. C. Determine the efficiency of the converter under the condition of part B.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Create a circuit of the Combinational Networks of the combination of BJT and FET with AC and DC supply. Solve it and show complete solution.
In the circuit of the following Fig , RC = 300Ω; RE = 200Ω; R1 = 2 k Ω; R2 = 15 kΩ; VCC = 15 V, and β = 110 for the transistor. Assume that ICQ = IEQ and VCEsat = 0. Find the VCEQ
For the multi-stage amplifier shown below, given the following T1: K = 0.12 mAV ?, VGS (TH) = 5 V, IDQ = 6.7 mA, VGSO = 12.5 V, RD1 = 2.9 kQ, (Assume rd >> Rp) % 3D% 3D T2: Ipss = 6 mA, Vp = -3 V, Ipo = 2.9 mA, VGSQ = -0.95 V, RD2 = 2.4 kQ. (Assume rd >> Rp)% 3D T3: R1 = 48 kQ, R2 = 12 kQ, Rc = 2.2 kQ. ro = 25 kQ, and B = 140 Calculate Ay1. Ay2, Ay3, and the overall voltage gain Avt
A transistor has Tox = 40 nm, VTN = 1 V,μn = 500 cm2/V ·s, L = 2 μm, and W = 20 μm.What are Kn and the saturated value of iD for thistransistor if VGS = 4 V? (b) The technology isscaled down by a factor of 2. What are the newvalues of Tox, W, L, VTN , VGS, Kn, and iD?
(a) We would like to measure the voltage (V = V1 − V2) appearing across the 20-kΩ resistor shown with a voltmeter. What is the value of V? What is the common-mode voltage associated with V(VCM = (V1 +V2)/2)? What CMRR is required of the voltmeter if we are to measure V with an error of less than 0.01 percent? (b) Repeat if the 10-kΩ resistor is changed to 100 Ω.
the oarameteris for m1 mosfet için It is given as . It is used as C1 = 10 mikro F, C3 = 100 mikro F in the circuit. According to this; a) Find the power spent on ml MOSFET. b) Find the numerical value of Rin resistance by performing the necessary mathematical operations b) The following equation is provided for the frequency value created by the C2 capacity in the circuit. So what is the value of C2 capacity? fc2 = 10 * (fci + fc3)
In the circuit given in the picture, the emitter follower is connected to a non-ideal voltage source Vs with a source resistance Rs.These are the value: beta =100Vbe = 0.7VVce,sat = 0V.The sub questions for this problem are:a. If Rs = 0 and Vs = 3V, determine the value of Vo.b. If Rs = 5k Ohms and Vs = 3V, determine the value of Vo.c. If Rs = 5k Ohms , determine the value of Vs that will cause the BJT to start saturating.
For the Circuit shown, Let: VCC = 3.3V R1 = 85 kΩ RE = 500 Ω R2 = 35 k Ω RC = 4k Ω β = 150 Using approximation, determine the Q-point parameters: IBQ, ICQ, and VCEQ. Indicate the exact numerical values, following the given unit.
(a) What is the total input capacitance in the circuit as shown if Cπ = 20 pF, Cμ = 1 pF, IC = 5 mA, and RL = 1 kΩ? What is the fT of this transistor? (b) Repeat for IC = 4 mA and RL = 2 kΩ.
For the circuit below, let K n’∙W/L = 4mA/V^2.a) Find the value of I that causes the MOSFET to operate in saturation with anoverdrive voltage of 0.25V.b) What value of RD results in V D = 0V?c) Find the value of g m .d) Find the value of ro given V A = 25V (λ = 1/(25V)).e) If Rin = 1MΩ, find the value that RG must be.f) For Rsig = 1MΩ and RL = 40kΩ, find the value of the overall voltage gain vo/vsig
Given the transistor circuit with beta as 100, solve the ff:a. Q-ptPlease show your complete solution thanks
Consider the amplifier circuit below.Both transistors are saturated (no need forDC analysis). 1) Draw the amplifier equivalent circuit using the pi-model for both transistors.2) Find the amplifier voltage gain.3) Find the amplifier input resistance.4) Find the amplifier output resistance. R(x) = 1.3 k(ohm)g(M1) = g(M2) = 1.3 mA/V