1. From the given figure below, determine the following: a. reactions at A & B. b. shear and moment at C & D. c. draw the shear and moment diagram of the given beam. 5|KN 20, KN 25 KN/m 10 KN B A C 1.5 m 1 m 1 m 0.5m |0.5m

1. From the given figure below, determine the following: a. reactions at A & B. b. shear and moment at C & D. c. draw the shear and moment diagram of the given beam. 5|KN 20, KN 25 KN/m 10 KN B A C 1.5 m 1 m 1 m 0.5m |0.5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 60 KN 60 kN 50 kN 30 kN/m 20 kN/m B H. 1.6m 1.6m 1.5m le5m 2m 1.4m 1.2m 0.6m

A: Solution: Considering the Diagram Free Body Diagram Part…

Q: 10 kN/m 50 kN OD 5 m B. 5 m 5 m. 5 m

A: To calculate the shear force and bending moment values first calculate reactions at supports and for…

Q: Determine the vertical reaction at A in the beam shown below? 50 kN/m 90 kN 60 kN 20 kN/m 70 kN 30°…

A: using equilibrium equations

Q: and moment. 60 kN 12 kN/m 200 kN - m B C A Esm– -10 m-

Q: 3.) DETERMINE THE MAGNITUDE OF FORCE F SO THAT THE RESULTANT FR OF THE THREE FORCES IS AS SMALL AS…

Q: 4 kN/m 5 kN 1m 2 kN.m 2m 2m 2m 2m

Q: b) For the beam shown Figure Q1b Calculate the value and directions of the reactions Calculate and…

A: Given data: Hinge at C.

Q: look for and show complete solution: a. Reactions b. Shear and Moment Diagram c. Maximum Moment d.…

A: For the beam shown below, the reactions, SFD, BMD, maximum moment and equations have to be…

Q: Determine the vertical reaction at B for the beam shown. 66.75 KN 53.4 kN 106.8 kN O a. By 160 kN ↑…

A: Given data Find vertical reaction at B (By)

Q: Q2: Determine the reactions and check stability of Frame structure. E 120 KN 10 KN/m 6 KN/m 1.75 120…

A: Note:- I'm solving here question 2 only, for Q.3 please resubmit the question. Condition for the…

Q: Problem 2: For the shown beam: a. Calculate the Equivalent Concentrated force FR for F the shown…

A: A uniform distributed load is a force delivered uniformly over the length of support. When a load is…

Q: 2. Draw the shear and moment diagram of the loaded beam shown in the figure. Determine the Vmax and…

Q: Determine the vertical reaction at A for the simply supported beam shown below? 80 kN/m 80 kN 20…

A: Support Reactions : ∑Fy = 0RA + RD = 80cos45o + 12×80×3 + 20×4 = 256.56 kN ............(1)∑Fx =…

Q: 3: Determine the magnitude of the Maximum shear force in the beam Vmax = 7.5 kNO Vmax = 50 kNO Vmax…

Q: (a) Derive the shear force and bending moment equations for the overhang beam. (b) Draw the shear…

Q: Question I: Determine the reactions and draw the shear and bending moment diagrams for the two-span…

Q: From the figure below, determine the fallowing a) reaction at A and B. b.) Shear and Moment at C and…

Q: Q.2) (a) Find the support reactions of the beam shown below. (b) Sketch the shear-force and bending…

A: Given:- A beam is given with different loadings The magnitude of the uniformly distributed load =…

Q: 1. Draw the shear and moment diagram. Determine the maximum shear and moment. 50 KN 150 kN - m' 15…

A: Firstly the support reactions in the beam should be calculated. Support reactions are shown in below…

Q: Problem IlI. A beam shown in Figure 1 is subjected to loads as shown. 59 kN 38 kN/m B 120 kN.m 68 kN…

Q: Use the graphical method to construct the bending-moment diagram and identify the magnitude of the…

A: Given Data:M=12 kN-mAy=3.37 kNDy=32.60 kN Required- To construct the bending-moment diagram and…

Q: For the beam shown, determine the following: a. Maximum Positive Shear b. Maximum Negative Moment c.…

A: Given data:

Q: What will be the value of the shear force at the fixed end A, at free end Band at point C for the…

A: Shear force at any section is resultant intertransverse force, which is equal to the algebraic sum…

Q: 10 kN/m B 20 KN 4 m 2 m 2 m a. Draw the shear diagram of the beam. b. Draw the moment diagram of the…

A: as per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: 70 kN/m y 25 kN/m A В C D 2.5 m 4.0 m 1.5 m

Q: 1. From the given beam, compute the following: a. reactions at A & B. b. shear and moment at D. c.…

A: Given data:

Q: Calculate the magnitude of the shear force (kN) V at a cross-section just to the right of the 6.0 kN…

A: Solution

Q: PART II. (BEAMS AND FRAMES : SHEAR AND BENDING MOMENT) DIRECTION : Answer the following questions.…

Q: Problem #4 Y N/m B A Am Cm 12. What is the total resultant vertical load in the beam AB? (N) 13. At…

Q: 3) The reaction force for the continuous beam with two hinge joints C and D as shown in Figure 3 has…

A: A continuous beam is generally a beam that has more than two supports, is statically indeterminate.…

Q: If the resultant force of the two tugboats is 3 kN,directed along the positive x axis, determine the…

A: Given: If the resultant force of the two tugboats is 3 kN, directed along the positive x axis,…

Q: QUESTION 2 Draw the free body diagram (FBD) for the overhanging beam. Determine support reactions.…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: Determine the reactions for the continuous beam shown by the three-moment equation. Draw the shear…

Q: Draw the shear and moment diagram of the following structures. 40 kN 8 kN/m 2. 20 kN 20 kN pin 6 kN…

A: Neglecting wh as we have tDs = 3m + r -3j - ehinge= 3×4 + 4 - 3×5 - 1×2-1Ds = 0Given structure is…

Q: A compound beam is subjected to three concentrated loads, as shown in Figure 2b. Using influence…

Q: 25 kN/m A В 50 kN-m 6 m

Q: A cantilever beam ABCD is shown in Figure QB2. (a) Determine the reaction force and reaction bending…

Q: A beam is loaded as shown in the given figure. 1. Which of the following gives the max. shear? a.…

A: to answer given questions based on given beam and loading.

Q: 5) An equivalent force-couple system: Three forces F1 = 100 N, F2 = 50 N, and F3 = 30 N act on a…

Q: Page | 4 QUESTION 4: Determine the reactions at A and B for the beam with an overhang and a…

Q: 1000 kN 500 kN.m 50KN/m 4 m 4 m 4 m 6m

Q: X N/m В В m Am 17. What is the total resultant vertical load in the beam AB? (N) 18. At what…

Q: (i) Calculate the reaction forces (ii) Draw shear force diagram (SFD) and bending moment diagram…

A: Calculating the reaction forces: Applying equilibrium conditions: Taking moment about point A:

Q: Given w=823 kN/m, find: (1) reaction forces at support A and B. (2) the internal forces 4m to the…

A: A UDL of 823 kN/m for 6 m. A point load of 100 kN acting downward. To determine support reactions…

Q: Problem #4 X N/m B В m Am 17. What is the total resultant vertical load in the beam AB? (N) 18. At…

Q: Q1 4 kN 14 kN 4 kN m 2 kN - m For the beam and loading shown in figure, answer the following…

A: given beam:

Q: Problem 5: (a) Replace the loading acting on the beam by an equivalent resultant force FR and couple…

A: From varignon's theorem can replace the the loading of beam into single force

Q: For the given beanm, the shear force diagram is illustrated as follows. Determine the maximum value…

A: Given data:

Q: Situation: For the beam shown in figure 4, Find the maximum shear force. a. 100 KN b. 60 kN C. 40 kN…

A: Given data Question-1 and 2 Find maximum shear force and maximum moment in beam. Question-3…

Q: 40.0 kN y 7.0 kN/m B 3 m 12 m 65.60 kN 58.40 kN 65.60 65.60 25,60 @x=6.66 m its: kN

Question

please answer correctly

1. From the given figure below, determine the following:
a. reactions at A & B.
b. shear and moment at C & D.
c. draw the shear and moment diagram of the given beam.
5|KN
20, KN
25 KN/m
10 KN
A
1.5 m
1 m
1 m
0.5m 0.5m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Interior finishes for wood light frame construction

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 4.8 ft, b = 3.5 ft, P = 30 kips, and w = 2.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Determine the reaction forces R1 and R2 and show the shear and bending moment diagram. Data: Point load (left-most) = 90.126 N RL1 (80mm to 160mm) = 65 N RL2 (160mm to 180mm) = 130 N RL3 (180mm to 260mm) = 65 N
Given the loaded beam below, calculate the reaction and draw the shear and moment diagram. M1= 20kN.m q1= 15 kN/m P1= 8kN
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
(i) A tie bar is 2.5 m long, has a circular cross section of 50 mm in diameter and is subjected to a force of 250 kN. Given that Young’s Modulus E = 209 kN/mm2 and Poisson’s Ratio ν = 0.3 calculate the change in volume of the bar when loaded. (ii) Draw the shear force and bending moment diagrams for the cantilever beam shown in the image attahced clearly indicating all significant points.
Use the graphical method to construct the bending-moment diagram and identify the magnitude of the largest moment (consider both positive and negative). The ground reactions and the shear-force diagram are provided. M = 12 kN-m Ay = 3.37 kN Dy = 32.63 kN
For the beam shown in figure below, draw the shear and moment diagrams: 1- Due to applied loads (without support settlement). 2- Due to support settlement of 60 mm downward at support B (without loads). Take the stiffness El as 12000 kN.m?. 50 kN SKN/m
In the figure on the right where there is a single load of 50 N at point B of the given rod system, (between AB: 4m / BC: 1m) a) Calculate the support reactions? b) Immediately after support A, just before point B and immediately after and just before the C-bracket Find the cross section effects by cutting? c) Draw the cross section effect diagrams?
For the beam presented below:a) What is the degree of indeterminacy; b) Determine the moment reactions at the supports and draw the shear and momentdiagrams. (Solve by expressing the internal moment in terms of vertical reactionsat A and B, EI is constant). c) What would the shear diagram look like if a transverse load P was applied right atthe middle of the beam (Make a sketch of the new shear diagram). W (30kN/m) , L (1.9m)
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Note that: a = 3.7 m b = 31.0 kN/m c = 35 kN Find the ff. A. Vertical reaction at B in kN. B. Moment reaction at A in kN-m. C. Deflection at point C in mm. D. Deflection at midspan of AB in mm.
look for and show complete solution: a. Reactions b. Shear and Moment Diagramc. Maximum Momentd. Equations w=022 Kn/m
(a) Figure Q2 shows a frame with tie rod at joint B and C. The beam carries a concentratedload 300kN at span BC. Analysis and sketch the shear force and bending-momentdiagram for the entire frame.