1.) Given the following properties of a rectangular concrete beam: b = 280mm, d = 480 mm, f'c = 21 MPa, fy = 414 MPa. The beam is reinforced for tension only. Determine the design strength under the following conditions. %3D %D a.) When the beam is reinforced with three 25 mm diameter bars. b.) When the beam is reinforced with four 25 mm diameter bars. c.) When the beam is reinforced with seven 25 mm diameter bars.

1.) Given the following properties of a rectangular concrete beam: b = 280mm, d = 480 mm, f'c = 21 MPa, fy = 414 MPa. The beam is reinforced for tension only. Determine the design strength under the following conditions. %3D %D a.) When the beam is reinforced with three 25 mm diameter bars. b.) When the beam is reinforced with four 25 mm diameter bars. c.) When the beam is reinforced with seven 25 mm diameter bars.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Principles of Reinforced and Prestressed Concrete If assumptions are made, verify if assumptions are correct. A reinforced rectangular beam with a with of 275 mm and effective depth of 440 mm has 4 16mm bars placed in 1 layer at the tension side. The beam has a stirrup with diameter of 10mm. Use fc'=28MPa and fy=420MPa, L=3.85m, w0=19.25kN/m and wl=24.75kN/m. Calculate the strength reduction factor of the beam.
A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 400 mm. Concrete strength is f’c = 28 MPa and steel yield strength is fy = 280 MPa. a. What is the distance of the neutral axis from the top of the beam so that the strain in the concrete 0.003 will be attained at the same time with the yield strain of steel? b. What is the total compressive force on concrete? c. What is the balanced steel ratio?
A simply supported beam 6.5m long, 350mmx500mm, prestressed with a straight tendon located 150mm below the neutral axis with effective prestressing force, Pe, of 300kN. Total load carried by the beam is 20kN/m. A. Determine the area of the concrete, mm2.B. Determine the section modulus of the concrete in x10^3 mm^3C. Determine the compressive stress caused by the tendon alone if Pe is at the centroid, MPa
A rectangular concrete beam has a width of 400 mm and an effective depth of 700 mm. It is reinforced with five 28-mm diameter bars for tension only. Concrete strength is f's = 21 MPa and steel yield strength is fy = 275 MPa. Which of the following most nearly gives the distance of the neutral axis from the extreme compression concrete? A. 139.51 mm B. 151.93 mm C. 118.58 mm D. 188.15 mm
Three high-strength concrete poles, with an effective cross- sectional area of 40, 000m * m ^ 2 and a length of 2 m, support a stiff steel plate. The center post is 1 mm shorter than the others before the load P is applied. If the concrete's allowed compressive stress is 20 MPa, calculate the maximum load that can be carried. E = 30GPa for concrete
A rectangular beam has a width of 260 mm and an overall depth of 470 mm. concrete cover is 60 mm from the centroid of bars. Concrete compressive strength f’c = 21 MPa. Steel yield strength fy = 415 MPa for longitudinal bars and 275 MPa for hoops. Determine the shear strength (in N) provided by concrete using the simplified calculation (a) if the beam is subjected to shear and flexure only. _______ (b) if the beam is subjected to axial compression force of 80 KN. ________
A pretensioned prestressed beam has a rectangular cross section of 6 in. width and 20 in. total depth. It is built using normal-density concrete with a specified strength f = 4000 psi and a strength at transfer of f' = 3000 psi. Stress limits are as follows: fi = 164 psi, f. = -1800 psi, f. = 474 psi, and fes = -1800 psi. The effectiveness ratio R may be assumed equal to 0.80. For these conditions, find the initial prestress force P, and eccentricity e to maximize the superimposed load moment My + M, that can be carried without exceeding the stress limits. What uniformly distributed load can be carried on a 30 ft simple span? What tendon profile would you recommend?
plz, solve all the parts of this problem. Use ACI code and Solve what you have been asked. Reinforced Concrete Design-1 A fixed ended beam with span length of 24′ and cross-section of 15ʺ x 24ʺ is subjected to uniformly distributed load is shown in figure 1. Unform service dead load is 1k/ft and uniform service live load is 1.4 k/ft. Taking ?c = 3?si and ?y = 40???, a) Analyze the beam for flexure only. b) Calculate the amount of reinforcement for the given demand and check for ductility requirements. c) Detail the reinforcement using #6 bar only, and also curtail the steel ensuring development length requirements. d) Show all your calculations in the form of neat and clean drafting. Note: Your drafting must include dimensional details, reinforcement details in both longitudinal and sectional views, and cut off locations of steel.
A rectangular beam has dimensions of 290 mm by 710 mm with an effective depth of 652 mm and is reinforced with 3- 20 mm ø. Concrete cover is 58 mm. The concrete cylinder strength f’c = 30.8 MPa and the tensile strength in bending is the modulus of rupture. The yield point of the steel is 414.2 MPa. The beam carries a bending moment of 66 kN-m. Use transformed section method to answer the following: (1) Compute the concrete compression stress at the top, (2) Compute the concrete tension stress at the bottom, (3) Compute the stress in the steel. (4) Assess the adequacy of the beam design.
If the elastic sag of the concrete member was 3 cm for the corresponding continuous load, what is the final total sag in consideration of additional long-term sag due to creep and dry contraction? (However, the load loading period is 10 years, and the compression reinforcement ratio p′=0.005)
Draw the correct Free Body Diagram (FBD). A concrete beam of 150 mm by 200mm and a length of 2 m has the density (mass/volume) of 3.85 Mg/m3, determine the weight of the beam in Newtons
A prestressed rectangular beam 0.50m x 0.75m has a simple span of 10m and is loaded with a uniform load of 45 kN/m including its own weight. The prestressing tendon is 0.225 m from the bottom and produces an effective prestress of 1600 kN. Compute the fiber stress distribution in the concrete at midspan (bottom fiber) due to axial and transverse loading. Select one: a. 3.26 MPa b. 1.96 MPa c. 2.61 MPa d. 4.08 MPa A prestressed rectangular beam 0.50m x 0.75m has a simple span of 10m and is loaded with a uniform load of 45 kN/m including its own weight. The prestressing tendon is 0.225 m from the bottom and produces an effective prestress of 1600 kN. Compute the fiber stress distribution in the concrete at midspan due to transverse load. Select one: a. 15 MPa b. 9 MPa c. 12 MPa d. 7 MPa