1. If K = 2.2 GPa is the bulk modulus of elasticity for water, what pressure is required to reduce a volume by 0.6 percent? 2. A liquid is compressed. The change in pressure is 1000 psi. The change in density is 0.02%. What is the bulk modulus in psi? 3. The temperature of liquid water decreases from 80°C to 20°C. The percent change in absolute viscosity is

Q: 2. The force (not just its magnitude) due to a solid body being compressed/stretched in the…

A: The force due to a solid body being compressed/stretched in the x-direction is given by…

Q: Darcy' Law A fluid's viscosity and unit weight are reduced to 60% and 80%, due to increase in…

A: Due to an increase in temperature, a fluid's viscosity and unit weight are reduced to 60% and 80%.

Q: What pressure is required to reduce the volume of water by 0.6 percent? Bulk modulus of elasticity…

A:

Q: The force per unit length is the unit of (a) surface tension (b) compressibility (c) capillarity (d)…

A: Number of multiple choice questions have been given and it has been asked to choose suitable answer.…

Q: A liquid has an absolute viscosity of 3.2 × 10^-4 Ib-sec/ft?. It weighs 56 Ib/ft³. What are its…

A: kinematic viscosity is ν=μρν=3.2×10-4lb-secft56lbft3ν=5.7143×10-6ft2sec

Q: 12) What pressure is required to reduce the volume of water by 0.6 percent? Bulk modulus of…

A: Given data: Reduce the volume of water=0.6% Bulk modulus of elasticity=2.2 GPa

Q: For any given velocity of flow, the friction factor "f" O will decrease as the diameter of the pipe…

A:

Q: 3. An amount of glycerin has a volume of 1.0 m3 when the pressure is 120 kPa. If the pressure is…

A: Hello dear this is the solution of your problem Please refer to the attachment, thanks

Q: By increasing the pressure of a liquid from 70 N/ cm² to 130 N/cm², its volume decreases by 0.15 per…

A: Given that: Initial pressure, P1=70 N/cm2Final Pressure, P2=130 N/cm2Volume decrease= 0.15%

Q: The excess of pressure in a soap bubble of diameter 10 mm, when the surface tension is 0.04 N/m is…

A:

Q: Ships and sailing vessels often carry lead ballast in various forms, such as bricks, to keep the…

A:

Q: A material has a dry mass of 115 g, volume in natural state is 55cm3, volume in absolute compact…

A: The values given in the question are as follows Dry mass(md)=115 g Volume in natural state(Vn)=55…

Q: When we were defining the bulk modulus of compressibility we said that as the pressure is increased,…

A: Solution:  Bulk modulus is the measurement of decrease in the value of volume with an increase in…

Q: The unit weight of a fluid is given by: y=mg/V. Prove that this equation is dimensionally…

A: An equation is said to be dimensionally homogeneous if all the terms on both sides of the equation…

Q: 1. What is the unit of coefficient of viscosity? a) kgsm2 b) kgms2 c) Nms 2 d) Nsm 2

A:

Q: The bulk modulus of water is 2.0 x 10° N/m². The pressure required to increase the density of water…

A: Bulk Modulus of water =2×109 N/m2

Q: The bulk modulus of water is 210x10 kN/m². What pressure is required to reduce the volume of water…

A:

Q: When a pressure of 20.7 MN/m is applied to 100 litres of a liquid its volume decreases by I litre.…

A: Given data : Initial volume (V)=100 litre Decrease in volume (dV)=1 litre Pressure applied (dP)=20.7…

Q: Find the change in volume of 10.00000 ft^3 of water at 80 deg.F. when subjected to a pressure…

A:

Q: 80 cm Ø water Wtank+water = 500 kg Wempty = 60 kg 200 cm

A:

Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…

A: Given data:Internal pressure, p=15 MPa or 15 N/mm2Inside diameter, d=20 mmWall thickness, t=10…

Q: A tri-metallic bar is uniformly compressed by an axial force P = 40 kN applied through a rigid end…

A:

Q: A solid brass sphere of volume 0.305 m3 is dropped in an ocean, where water pressure is 2 x 107 N/m2…

A:

Q: 2. A solid ball 300 cm in diameter is submerged in a lake of such depth that exerted by water is 9.8…

A: Diameter of ball d= 300 cm So, radius of ball ,r = d/2 = 150 cm Pressure applied ,P = 9.8 x 104 N/m2…

Q: Q2: -Determine the center of the mass of the solid block shown in figure below. The density are…

A: Mass=Density×volumem=P×Vx¯=∑mixixi¯∑MiTriangle 1=P×12×1.8×1.5m1=P×1.35

Q: A tri-metallic bar is uniformly compressed by an axial force P = 40 kN applied through a rigid end…

A:

Q: . A piece of solid weighs 120 g in air, 80 g in and 60 g in a liquid. The relative density solid and…

A: Wt in air=120g Wt in water= 80g Wt in liquid=60g

Q: A liquid undergoes a pressure change of 6x10^4 N/m^2 and its volume decreased by 0.1 cm^3 resulting…

A: solution Change in pressure dP =6×104 Nm2=6 Ncm2volume decreased dV=-0.1cm3final volume…

Q: An aluminum cylinder (s.g3D2.7) 15 cm high and with diameter d%38.1 cm slides down inside a tube…

A: For calculating the terminal velocity , i.e. constant velocity assuming that the cylinder lies in…

Q: A liquid flowing from a reservoir thru a non-rigid 600 mm diameter pipe with a velocity of 2.5 m/s…

A: The formation of the water hammer effect in the water carrying pipes are governed by two different…

Q: Consider the following conditions: Condition I Condition 2 A wooden cube of size 2 m and the 20% of…

A: Given data, Condition - 1 Wooden cube size = 2 m Relative density = 0.5  Condition - 2 20% of the…

Q: 1. Eight kilometers below the surface of the ocean the pressure is 81.4 MPa. Determine the density…

A: Given: The ocean pressure is P8 km=81.4 MPa. The atmospheric pressure is Patm=0.101 MPa. The density…

Q: Absolute viscosity of a fluid varies w/ pressure and temperature and is defined as a function of:…

A: Correct answer is option b. Density, shear stress and angular deformation rate

Q: 1. The value of the viscosity of an ideal fluid is a) zero b) unity c) infinity d) more than that of…

A: Ideal fluid are those fluid which are non viscous in nature which means it has zero viscosity . The…

Q: 1) A liquid has an absolute viscosity of 2.4x10 N-s/m2. It weighs 7.85x103 N/m³. What is its…

A:

Q: An amount of glycerin has a volume of 1 m' when the pressure is 120 kpa. If the pressure is…

A:

Q: An air compressor used by a mechanic for filling air in tyre is cylindrical in shape which has…

A:

Q: r. Determine the ratio of force exerted by water to oil

A:

Q: 9. For liquid fluids will capillarity rise (or fall) increase or decrease with rise in temperature.…

A: Capillarity is a phenomenon of rise of liquid through a tube because of surface tension.

Q: 50 mm C 175 mm B. -225 mm -300 mm Bar ACB shown in the Figure is subjected to a uniform temperature…

A:

Q: The pressure of a liquid is increased from 60 N/cm^2 to 100 N/cm^2 and volume decreases by 0.2…

A: To determine the bulk modulus of elasticity of a liquid with given information.   The Bulk Modulus…

Q: A line was determined to be 2395.25 m. when measured with a 30-m steel tape supported throughout its…

A: Given standard length of tape,L=30m measured distance=2395.25m temperature at measurement,Tm=35°c…

Q: The Reynolds transport theorem provides a way to relate what is happening to the system and what is…

A: This question is from fluid mechanics Here we are asked to find out the first term of Reynolds…

Q: A liquid has a dynamic viscosity of 4.8x10* lb-s/ft² and weighs 54 lb/ft³. What is its kinematic…

A: Given:- Dynamic viscosity=4.8×10-4 lb-s/ft2Weight=54 lb/ft3 To find:- From the given question it is…

Q: A plastic cube of side L with Specific Gravity of 0.82 is vertically placed in water. Is the cube…

A:

Q: PROBLEM 3. If a pressure applied to 1 kg of water is 13.2 x 10^7 N/m^2 causes a percentage reduction…

A: Bulk modulus, B=ΔPΔVV ΔP = Change in pressure in N/m2 ΔV = Change in volume in m3 V = Actual volume…

Q: 1.3 A liquid at 20°C has a relative density of 0.80 and a kinematic viscosity of 2.3 centistoke.…

A:

Q: A liquid has an absolute viscosity of 2.231025 Ib-s/ft. It weighs 45 Ib/ft'. What is its kinematic…

A: solution Given absolute viscosity μ=2.231025 lb-sft21pas -sec =147.88  lb-sft2 so  μ=2.231025×47.88…

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.