1. If the spring is compressed a distance 6 and the coefficient of static friction between the tapered stub S and the slider A is UsA, determine the horizontal force P needed to move the slider forward.The stub is free to move without friction within the fixed collar C. The coefficient of static friction between A and surface B is HAB. Neglect the weights of the slider and stub. Given: 8 = 60 mm HsA = 0.5 HAB = 0.4 N k = 300 e = 30 deg

1. If the spring is compressed a distance 6 and the coefficient of static friction between the tapered stub S and the slider A is UsA, determine the horizontal force P needed to move the slider forward.The stub is free to move without friction within the fixed collar C. The coefficient of static friction between A and surface B is HAB. Neglect the weights of the slider and stub. Given: 8 = 60 mm HsA = 0.5 HAB = 0.4 N k = 300 e = 30 deg

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.8P: The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of...

See similar textbooks

Similar questions

The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The two uniform sheets of plywood, each of length L and weight W, are propped as shown. If the coefficient of static friction is 0.5 at all three contact surfaces, determine whether the sheets will remain at rest.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The panel of weight W with its center of gravity at G is placed between vertical guides and released. Determine the largest height h for which the panel will not slide down due to binding at corners A and B. The coefficient of static friction between the panel and the guides is 0.5.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The 120-kg block A is suspended from a rope that runs around the fixed pegs B and C. The coefficient of static friction between the pegs and the rope is 0.25. Determine the range of the force P for which the system is in equilibrium.
The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
Find the largest value of b/h at which the folding table is in equilibrium. The coefficients of static friction are 0.5 at A and 0.3 at C. Neglect the weight of the table.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
roll of paper has a uniform weight of 2kN and is suspended from the wire hanger so that it rests against the wall. If the hanger has a negligible weight and the bearing at O can be considered frictionless, determine the force P needed to start turning the roll if = 30°. The coefficient of static friction between the wall ܬܐ and the paper is µ = 0.3.