1. In a parallel communication, each bit requires a transmitter and receiver.a) Trueb) False2. What is the cable that carries the information in parallel transmissioncalled?a) Parallel lineb) Data busc) Data lined) Data link3. Which of the following is a false reason for parallel lines not being used forlong distances?a) Cost factorb) Signal Attenuationc) Number of transmission channelsd) Low speed4. Why higher speed communications in parallel transmission require shorterlength?a) Costb) Resistancec) Inductive and capacitance effectsd) Noise5. Which bit is transmitted first in a serial communication?a) Least significant bitb) Most significantc) All the bits simultaneouslyd) Not in any specific order6. In serial communication, if the time interval to transmit one bit is 10us.What is the time to transmit an 8-bit word?a ) 8μsb) 80µsc) 0.8µsd) 0.008µs

Note : As per bartleby guidelines we are allowed to solve first question only.

1. In a parallel communication, each bit requires a transmitter and receiver. a) True b) False 2. What is the cable that carries the information in parallel transmission called? a) Parallel line b) Data bus c) Data line d) Data link

1. In a parallel communication, each bit requires a transmitter and receiver. a) True b) False 2. What is the cable that carries the information in parallel transmission called? a) Parallel line b) Data bus c) Data line d) Data link

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 2RP

See similar textbooks

Related questions

Q: 22: In PSK system the bit rate of NRZ stream is 20 Mbps and carrier frequency is 2GHZ. Find the…

A: Answer is given below-

Q: Draw the corresponding encoding of the digital data given below.

A: ANSWER: As presented in past area, the 9 images in Huffman code can be addressed with paired…

Q: 6) You are trying to calculate what the theoretical maximum throughput is on a given communication…

A: A music signal is characterized by a rms voltage of 2 V and a bandwidth B of 15 kHz. A noise process…

Q: 1. A line has a signal-to-noise ratio of 1000 and a bandwidth of 4000 KHz. What is the maximum data…

A: The answer as given below:

Q: Bit or symbol transmission time: Based on the maximum gross bit rate (the transmission rate) R in…

A: Bit rate is the transmission of a number of bits per second. The Baud rate is defined as the number…

Q: d. Assume that the data is transferred using a 4B5B bit synchronization and error detection code (4…

A: In telecommunication, 4B5B is a form of data communications line code. 4B5B maps groups of 4 bits of…

Q: Can I have a detailed, step-by-step explanation for the following question? Thank you very much!…

A: We have 4 channels that are multiplexed using TDM. If each channel sends 100 bytes/second and we…

Q: A serial transmission T1 uses 8 information bits, 2 start bits, 1 stop bit and 1 parity bit for each…

A: Introduction serial transmission T1 info bits 8 Start bit 2 Stop bot 1 Parity bit 1 synchronous…

Q: Why does the time interval between bytes in asynchronous transmission vary?

A: The gap time between bytes is "variable" in asynchronous transmission. Explanation: Asynchronous…

Q: For a ______ channel, the Nyquist bit rate formula defines the theoretical maximum bit rate. a.…

A: Answer :- ( b ). noiseless

Q: Exercise (1): A line has a Signal-to-Noise ratio 35dB and a bandwidth of 4000HZ, what is the maximum…

A: Data rate governs the speed of data transmission. A very important consideration in data…

Q: Q3. A signal is carrying data in which one data element is encoded as one signal element (r = 1). If…

A: Note: As per Bartleby's answering guidelines, only one question can be answered at a time. Hence, Q3…

Q: 7. We want to transmit 5000 characters with each character encoded as 8 bits. Find the number of…

A: Asynchronous and Synchronous transmission.

Q: In asynchronous transmission, why does the gap time between bytes differ?

A: Introduction: Because Transmission is asynchronous, the time interval between bytes is "variable."

Q: Explain the difference between transmission delay and throughput.

A: Below are the differences between Transmission delay and Throughput.

Q: a- Explain the Stop-and-Wait protocol

A: Answering first part as per the guidelines. The problem is based on the basics of computer…

Q: The physical layer is responsible for a. line coding b. channel coding c. modulation d. all of the…

A: The physical layer is one of the layers in the OSI network model that mainly deals with the physical…

Q: 2. (a) Suppose a radio channel occupies a bandwidth of 11 kHz. We need to multiplex 14 radio…

A: a) Bandwidth occupied by radio channel =11 KHzNeed to multiplex 14 radio channels with guard binds…

Q: 9. Assume we have three channels, two with bit rates of 100 kbps and another with a bit rate of 200…

A: The question is on solving Q9 related to Time Division Multiplexing.

Q: 2. Determine the correct answer. d) In binary 0 is received, or a binary 0 is transmitted and a…

A: AS PER OUR POLICY “Since you have posted a question with multiple sub-parts, we will solve the first…

Q: 254. In OOOVBOVB, V stands for violation and B stands for a. Bit b. Baud c. Bandwidth d. Bipolm

A: Given that, In OOOVBOVB, V stands for violation and B stands for a. Bit b. Baud c. Bandwidth d.…

Q: Define the width of a bit, W, to be its length on the transmission medium in meters per bit. Let S…

A: Transmission delay = packet size/bandwidth It's the total amount of time required to put data onto…

Q: 5. Assume that there are five 1 kbps connections to be multiplexed together. A unit is 1 bit. Find…

A: Ques 5). Before Solving the question we need to know that "what is multiplexing?". "It is the set…

Q: asynchronous

A: Clocks of the beneficiary and transmitter , independent unsynchronized, however of same…

Q: 3) What is the key advantages of a serial data transfer? What are the drawbacks to a serial data…

A: Below is the answer to above questions. I hope this will meet your requirement..

Q: 194. What is the usual number of bits transmitted simultaneously in parallel data transmission used…

A: Given:- What is the usual number of bits transmitted simultaneously in parallel data transmission…

Q: What causes the time interval between bytes in asynchronous transmission to vary?

A: Answer is given below -

Q: 5. The cheapest modems can transmit a. 100 bits per second b. 300 bits per second c. 600 bits per…

A: Lets see the solution.

Q: Discuss the advantages and disadvantages of both Byte Count and Byte Stuffing framing techniques of…

A: Advantages of byte stuffing framing technique of data link layer are : End and start can be easily…

Q: What is meant by "asynchronous" in the topic of Asynchronous Communications? O No clock is…

A: 1) Serial data transfer can be grouped into two types: Synchronous: Both the sender and receiver…

Q: The physical layer is concerned with the movement of over the physical medium. Select one: a.…

A: For question 1 The physical layer is concerned with the movement of Bits over the physical medium.…

Q: 5.c How many bytes would it take to store original message? How many bytes does it take to store the…

Q: What is the maximum number of characters (7 bits + parity ) that can be transmitted in asecond on a…

A: There is always a start bit and stop bit present in asynchronous transmission mode. Therefore here…

Q: In 8 bit data transmission system the transmitted data X, Y and Z after adding an EVEN Parity. The…

A: Given 8 bit transmission system the transmitted data X,Y,Z after adding an EVEN parity and we need…

Q: Which of the two data transmission methods do you think is better? Parallel or serial? Why?

A: We are going to understand which data transmission methods - Parallel or serial is better and why.

Q: 7. Two channels, one with a bit rate of 190 kbps and another with a bit rate of 180 kbps, are to be…

A: Answer

Q: A common measure of transmission digital data is the baud rate, defined as the number of bits…

Q: In digital transmission, the receiver clock is 0.2 percent slower than the sender clock. Answer the…

Q: True or false, and briefly explain your response to the following questions. The alternating-bit…

A: SR: It is a selective repeat protocol utilized in the data link layer of the OSI model to achieve…

Q: We want to transmit 600 characters/s, where each character is represented by its 6-bit ASCII…

A: Effective transmission rate is the rate at which information is processed by a transmission…

Q: c) One of the challenges in time-division multiplexing is how to handle a disparity in the input…

A: Given The answer is given below.

Q: Question 3-]: {500,600,700,800} to: Apply the FHSS using 2 bits and the frequencies 1- Write the…

Q: Assume that the data is transferred using a 4B5B bit synchronization and error detection code (4 net…

A: Block: Block secret writing helps in error detection and re-transmission of the signal. it's…

Q: The physical layer is responsible for

A: The physical layer is responsible for

Q: 6) You are trying to calculate what the theoretical maximum throughput is on a given communication…

A: Given Bandwidth (B) = 15kHz = 15000 Hz Number of signal levels (M) = 2 Theoretical Maximum…

Q: 3- Which is the last bit transmitted in a serial communication? a) Least significant bit b) All the…

A: The answer to the given question is in next step.

Q: Bit or symbol transmission time: Based on the maximum gross bit rate (the transmission rate) R in…

A: Answer is given below .

Concept explainers

Types Of Protocols

A network protocol is a collection of rules that governs the exchange of data between devices connected to the same network. In other words, network protocols are rules that specify how devices communicate or transfer data over a network. The sender and receiver systems must obey the standards to facilitate communication between them.

Question

1. In a parallel communication, each bit requires a transmitter and receiver.
a) True
b) False
2. What is the cable that carries the information in parallel transmission
called?
a) Parallel line
b) Data bus
c) Data line
d) Data link
3. Which of the following is a false reason for parallel lines not being used for
long distances?
a) Cost factor
b) Signal Attenuation
c) Number of transmission channels
d) Low speed
4. Why higher speed communications in parallel transmission require shorter
length?
a) Cost
b) Resistance
c) Inductive and capacitance effects
d) Noise
5. Which bit is transmitted first in a serial communication?
a) Least significant bit
b) Most significant
c) All the bits simultaneously
d) Not in any specific order
6. In serial communication, if the time interval to transmit one bit is 10us.
What is the time to transmit an 8-bit word?
a ) 8μs
b) 80µs
c) 0.8µs
d) 0.008µs

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Suppose that a sender and a receiver exchange data via UART with followingconfiguration:Baud rate = 115200 bits/s 1 start bit, 2 stop bits, 8 data bits, 1 parity bit 16 clock periods used for sampling 1 bit Answer the following questions please and thank you(a) What is the required clock frequency?(b) Suppose a 48 MHz clock. What is a suitable division factor to generate the neededclock in sub-question (a)?(c) How long does it take to transfer 10 MBytes of data?
a. Assume there are one million books in your campus library. Approximate (to the nearest order of magnitude) how many bytes of data there are if all these books were stored online and accessible across a computer network. b. How long does it take to transfer the entire collection of books if the data rate of the transmission medium is 10 Mbps, the speed of the original Ethernet? How long does it take if we have a line with a speed of 1 Gbps? (This value represents the time needed to download your entire campus library.)
Assume that the data is transferred using a 4B5B bit synchronization and error detection code(4 net bits transferred using 5 bits). what is the physical layer gross bit rate? Show all calculations
Q. 2. (b) Suppose Robi has 32 voice channels, each of 60 Mbps. They use synchronous TDM to multiplex these channels. If two characters at a time is multiplexed (two characters in each output slot), answer the following questions: i) What is the size of an output frame in bits? ii) What is the output frame rate? iii) What is the duration of an output frame? iv) What is the output data rate? v) Input bit duration?
1. In a data link layer-level communication, sender wants to send following data in bits 1100111101110101110010101001 using n-bit Parity Check where n is equal to 7. Hence, total size of data block would be _____ bits. 2. Calculate the data block mentioned in the 1st question.
Computer Science Suppose that you had more than 4GByte of data to send and could only afford one memory stick but you had plenty of pigeons available (Winston’s extended family). You reason that you can send the data stick back, load it with the next 4GByte of data. What would the throughput of this channel be now?
5. Consider the CDMA technique and assume that users A and B have spreading codes 01010101 and 01011010, respectively. Denote bit 0 as -1 and bit 1 as +1. (a) How can one determine if these two spreading codes are orthogonal? (b) What is the compound signal content if A sends a data bit 0 and B sends a data bit 1? (c) What data bit is transmitted by users A and B, respectively, if the compound signal content is (0, 0, 0, 0, -2, 2, -2, 2)? (d) How can a user know that the received signal content does not contain relevant data bits to
Assume we need to download text documents at the rate of 500 pages per second (each page is 24 lines with 80 characters per line (8 bits per character)). What is the required bit rate of the channel?
Suppose we want to download text documents at the rate of 100 pages per second. Assume that a page consists of an average of 24 lines with 80 characters in each line. What is the required bit rate of the channel?
1. Name the advantages of optical fiber over twisted-pair and coaxial cable. 2. Compare and contrast (major points) between a circuit-switched network and a packet-switched network. 3. The two types of networks, datagram and virtual-circuit, need a routing or switching table to find the output port from which the information belonging to a destination should be sent out, but a circuit-switched network has no need for such a table. Give the reason for this difference. 4. What is the Hamming distance for each of the following codewords: a. d (10000, 00100)b. d (00101, 10000) 5. Find the minimum Hamming distance for the following…
2. Twelve sources, eight with a bit rate of 250 kbps and four with a bit rate of 500 kbps are to be combined using multilevel TDM with no synchronizing bits. Answer the following questions about the final stage of the multiplexing: a. Compute the size of a frame in bits? b. Compute the frame rate? c. Compute the duration of a frame? d. Compute the data rate?
Explain the concept of bandwidth and its importance in the context of transmission media. How does it relate to data transfer rates?